Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Landoll Manuals
  4. Farm Equipment
  5. 2411
  6. Operator's manual

Landoll 2411 Operator's Manual

Weatherproofer
Hide thumbs

Advertisement

Quick Links

Download this manual
'
Model 2411
Weatherproofer
Operators Manual
LANDOLL COMPANY, LLC
1900 North Street
Marysville, Kansas 66508
(785) 562-5381
800-428-5655 ~ WWW.LANDOLL.COM
F-1130-2304

Advertisement

loading
Need help?

Need help?

Do you have a question about the 2411 and is the answer not in the manual?

Questions and answers

Related Manuals for Landoll 2411

Summary of Contents for Landoll 2411

  • Page 1 ‘ Model 2411 Weatherproofer Operators Manual LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-1130-2304...
  • Page 2 The identification plate, which lists the model number and serial number, is located on the front of the frame. SERIAL NUMBER The serial number is located on the identification plate. The Following information will help decode the 2411 Weatherproofer serial number 24H220000 = xxmyysssss QR CODE DECAL...
  • Page 3 DANGER DO NOT operate or perform any maintenance tasks on this equipment until you have completed the following: 1. Receive proper training to operate this equipment safely. 2. Read and understand the operator’s manual. 3. Be thoroughly trained on inspection and repair procedures. Failure to comply with this warning may result in serious injury or possibly death.
  • Page 5 Assembly Instructions Center Frame and Lift Assembly 2411-06 ......3-2 Center Frame and Lift Assembly 2411AFG-07-09 ....3-6 Center Frame and Lift Assembly 2411AFG-07-09 After 08/01/2022 .
  • Page 6 TABLE OF CONTENTS Leveling (Front-to-Rear)........4-6 Disc Blades .
  • Page 7 TABLE OF CONTENTS Introduction and Safety Information The Landoll Model 2411 Weatherproofer a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation.
  • Page 8 (decals) The safety statements contained in this manual relate to attached to the machine. This section explains their the operation of the Model 2411 Weatherproofer. meaning.  1. Examine safety decals and be sure you have the correct safety decals for the implement.
  • Page 9 TABLE OF CONTENTS Transporting Safety Maintenance Safety 1. Understand the procedure before doing the work. Use IMPORTANT proper tools and equipment. It is the responsibility of the owner/operator to 2. Make sure all moving parts have stopped. comply with all state and local laws. 3.
  • Page 10 TABLE OF CONTENTS Prepare for Emergencies Safety Chain 1. Keep a First Aid Kit and Fire Extinguisher handy. 1. Use a chain with a strength rating equal to or greater than the gross weight of towed machinery, which is 2. Keep emergency numbers for doctor, ambulance, 10,100 pounds minimum in accordance with ASAE hospital, and fire department near the phone.
  • Page 11 TABLE OF CONTENTS Safety Decals and Reflectors New safety signs may be ordered from your Landoll dealer. Refer to this section for parts and proper safety The 2411 Weatherproofer equipped with all safety signs sign placement. installed for safe operation.
  • Page 12 TABLE OF CONTENTS P/N 155523 Model 2411-06 Hose Identification Front of hitch, 2nd from left QTY. 1 P/N 155523 Model 2411AFG-07-09 Hose Identification Front of hitch, 3rd from left QTY. 1 P/N 207142 Model 2411-06 Danger: Stuck Shank Front of hitch, 3rd from left QTY.
  • Page 13 TABLE OF CONTENTS P/N 207142 Model 2411-06-07-09 Danger: Stuck Shank Left side, spring shank weldment QTY. 1 each P/N 2-573-010037 Model 2411AFG-07-09 Danger: Folding wing Front, side, front tube, center frame, both sides QTY. 4 P/N 2-573-010037 Model 2411AFG-07-09 Danger: Folding wing Rear, side, center frame, both sides QTY.
  • Page 14 TABLE OF CONTENTS P/N 144193 Model 2411AFG-07-09 SIS 20MPH Front side, front fold plate QTY. 2 P/N 528934 Model 2411-06 Yellow Reflector Left front, center frame, both sides QTY. 2 P/N 528934 Model 2411AFG-07-09 Yellow Reflector Left front, center and wing frame, both sides QTY.
  • Page 15 TABLE OF CONTENTS P/N 528934 Model 2411AFG-07-09 Yellow Reflector Left rear, center and wing frame, both sides QTY. 4 P/N 528934 Model 2411-06 Yellow Reflector Left center frame, middle, front light bracket, both sides QTY. 4 P/N 528934 Model 2411AFG-07-09...
  • Page 16 TABLE OF CONTENTS P/N 528938 Model 2411AFG-07-09 Orange Reflector Back side, rear fold plate, top QTY. 2 P/N 528938 Model 2411-06 Orange Reflector Back side, front, light bracket both sides, top, both sides QTY. 2 P/N 528938 Model 2411AFG-07-09 Orange Reflector Back side, front, light bracket both sides, top, both sides QTY.
  • Page 17 TABLE OF CONTENTS P/N 528933 Model 2411AFG-07-09 Red Reflector Back side, rear fold plate, bottom QTY. 2 P/N 528933 Model 2411-06 Red Reflector Back side, front, light bracket both sides, bottom, both sides P/N 528933 Model 2411AFG-07-09 Red Reflector Back side, front, light bracket both sides, bottom, both sides QTY.
  • Page 18 TABLE OF CONTENTS P/N 528938 Model 2411AFG-07-09 SMV Emblem Back side, rear fold plate QTY. 1 P/N 224589 Model 2411-06 SIS 20 mile/h Back side, SIS decal mount QTY. 2 P/N 224589 Model 2411AFG-07-09 SIS 20 mile/h Back side, rear fold plate QTY.
  • Page 19 10 days of purchase or lease, in so as to be able to follow the suggestions made. Please order to be on file at Landoll and eligible for Warranty. take time to understand the proper maintenance schedule and SAFE operation of your equipment.
  • Page 20 1) subjected to or operated in a manner which, at any time, have exceeded the product design limits: 2) repaired or altered outside our factory in any way so as, in the judgment of Landoll Company, LLC , to affect its stability or reliability: 3) subject to misuse, negligence, accident, or has been operated in a manner expressly prohibited in the instructions;...
  • Page 21 This exclusive remedy shall not be deemed to have failed of its essential purpose so long as Landoll Company, LLC is willing and able to repair or replace defective parts in the prescribed manner.
  • Page 22 TABLE OF CONTENTS General Torque Specifications (rev. 4/97) TORQUE SPECIFIED IN FOOT POUNDS This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and cap-screws assembled without supplemental lubrication (as received condition).
  • Page 23 TABLE OF CONTENTS Hydraulic Fitting Torque Specifications TORQUE IS SPECIFIED IN FOOT POUNDS- 37 JIC, ORS, & ORB (REV. 10/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).
  • Page 24 TABLE OF CONTENTS Model Specifications 2411 Weatherproofer Model Number 2411-6-24 2411-7-24 2411-9-24 Working Width 12'-0” 14'-0” 18'-0” Transport Width 15'-4” 14'-6” 14'-6” Transport Height 12'-4” 13'-6” Number of Blades F/R 16/18 18/20 24/24 Number of Shanks Shank Spacing 24” 24”...
  • Page 25 TABLE OF CONTENTS Table provided for general use. NOTES:...
  • Page 26 TABLE OF CONTENTS Shank Placement 8-1/2" 8-1/2" 12-1/2" 12-1/2" 12-1/2" 7-1/2" 7-1/2" Figure 2-2: Shank Placement Assembly 2410-06 F-1130-2304...
  • Page 27 TABLE OF CONTENTS 7-7/8" 8" 8" 12-1/2" 12-1/2" 12" 12" Figure 2-3: Shank Placement Assembly 2410-07...
  • Page 28 TABLE OF CONTENTS 7-7/8" 10-3/4" 10-3/4" 8" 8" 12-1/2" 12-1/2" 12" 12" Figure 2-4: Shank Placement Assembly 2410-09 2-10 F-1130-2304...
  • Page 29 NOTE: LOCATION BULKHEAD FITTINGS OF HOSE CLAMPS 10-1/8" 10" NOTE: LOCATION OF HARROW ADJUSTMENT WRENCH’S 13" 13" 4 TINE HARROW 4 TINE HARROW ASSEMBLY LH ASSEMBLY RH REEL/GANGBAR REEL/GANGBAR ASSEMBLY 97” ASSEMBLY 97” Figure 2-5: 3BCT W/Hydraulic Chopper Placement 2411-06 2-11...
  • Page 30 NOTE: LOCATION OF HARROW ADJUSTMENT WRENCH’S 7-7/8" 7-7/8" 23-1/4" 3 TINE HARROW 3 TINE HARROW 3 TINE HARROW ASSEMBLY LH ASSEMBLY ASSEMBLY RH REEL/GANGBAR REEL/GANGBAR REEL/GANGBAR ASSEMBLY 64” ASSEMBLY 91” ASSEMBLY 64” Figure 2-6: 3BCT W/Hydraulic Chopper Placement 2411-07 2-12 F-1130-2304...
  • Page 31 NOTE: LOCATION OF HARROW ADJUSTMENT WRENCH’S 7-7/8" 7-7/8" 23-1/4" 4 TINE HARROW 3 TINE HARROW 4 TINE HARROW ASSEMBLY LH ASSEMBLY ASSEMBLY RH REEL/GANGBAR REEL/GANGBAR REEL/GANGBAR ASSEMBLY 91” ASSEMBLY 91” ASSEMBLY 91” Figure 2-7: 3BCT W/Hydraulic Chopper Placement 2411-09 2-13...
  • Page 32 ASSEMBLY ASSEMBLY ASSEMBLY ASSEMBLY DISC LIFT TUBE 75” DISC LIFT TUBE 75” DISC LEVELER ASSEMBLY DISC LEVELER ASSEMBLY MOUNT TUBE 92” MOUNT TUBE 92” REEL/GANGBAR REEL/GANGBAR ASSEMBLY 97” ASSEMBLY 97” Figure 2-8: Disc Lev/Hyd RL Layout Placement 2411-06 2-14 F-1130-2304...
  • Page 33 DISC LIFT TUBE 50-3/4” DISC LEVELER ASSEMBLY DISC LEVELER ASSEMBLY DISC LEVELER ASSEMBLY MOUNT TUBE 54-1/2” MOUNT TUBE 84” MOUNT TUBE 54-1/2” REEL/GANGBAR REEL/GANGBAR REEL/GANGBAR ASSEMBLY 75” ASSEMBLY 64” ASSEMBLY 75” Figure 2-9: Disc Lev/Hyd RL Layout Placement 2411-07 2-15...
  • Page 34 DISC LIFT TUBE 72-3/4” DISC LEVELER ASSEMBLY DISC LEVELER ASSEMBLY DISC LEVELER ASSEMBLY MOUNT TUBE 77-3/4” MOUNT TUBE 84” MOUNT TUBE 77-3/4” REEL/GANGBAR REEL/GANGBAR REEL/GANGBAR ASSEMBLY 97” ASSEMBLY 64” ASSEMBLY 97” Figure 2-10: Disc Lev/Hyd RL Layout Placement 2411-09 2-16 F-1130-2304...
  • Page 35 Chapter 3 TABLE OF CONTENTS Assembly Instructions It is very important that your new 2411 Weatherproofer WARNING be properly assembled, adjusted and lubricated before use. Illustrations to assist with the assembly process are Do not attempt to lift heavy parts (such as the provided in “Standard Specifications”...
  • Page 36 9. Slide the rear of the hose support tube into the hose tube support plate, secure the front of tube to the top 2411-06 of the DCV/hose mount plate using 1/2 x 3 square bolts and 1/2 lock nuts. Attach the hose clamps to the...
  • Page 37 FRONT BOLT PLATES, DCV/HOSE MOUNT PLATE, STAND LT LIGHT BRACKET 7/8 X 7 GR8 BOLTS, ASSEMBLY, 1/2 X 3-1/2 CENTER FRAME 7/8 FLAT WASHERS, BOLTS, 1/2 WASHERS, WELDMENT LT 7/8 LOCK NUTS 1/2 LOCK NUT FRONT Figure 3-1: Center Frame Assembly 2411-06...
  • Page 38 SLIDE PLATE, LIMIT VALVE, BEARING LIFT MOUNT, FRONT 5/16 X 5-1/2 BOLTS, 3/4 X 2 BOLT, 5/16 LOCK NUT 3/4 LOCK NUT NOTE: MOUNT LIMIT VALVE WITH PLUNGER FACING TO REAR OF MACHINE Figure 3-2: Center Frame Lift Assembly 2411-06 F-1130-2304...
  • Page 39 TABLE OF CONTENTS Table provided for general use. NOTES:...
  • Page 40 TABLE OF CONTENTS Center Frame and Lift Assembly NOTE 2411AFG-07-09 Be sure the 4, 1-5/8 x 1-1/4 x 1 bushings are installed in the lift plate mounts and center lift assembly mount plates See Figures 3-3. IMPORTANT 7. Install a 1-1/4 x 1 spacer in rod and base end cylinder Read all safety precautions at the front of the section clevis.
  • Page 41 TABLE OF CONTENTS REAR TOWER PLATE 1-1/4 X 1 SPACER, 1-5/8 X 1-1/4 X 1 BUSHINGS, ASSEMBLY 4-1/2 X 16 CYLINDERS, 1-1/4 X 7 PINS, 1-1/4 WASHERS, CENTER FRAME 5/16 X 2-1/2 SPRING PINS ASSEMBLY RT LIGHT BRACKET ASSEMBLY, 1/2 X 4-1/2 BOLTS, 1/2 WASHERS, 1/2 LOCK NUT WING STOP MOUNT...
  • Page 42 TABLE OF CONTENTS Center Frame and Lift Assembly 8. Install the transport locks to the light brackets with the l-pin and hairpin clip. 2411AFG-07-09 After 08/01/2022 9. Install hose clamp to center frame weldment LT assembly with 3/8 x 1-1/2 bolt, 3/8 flat washer and 3/8 lock nut.
  • Page 43 TABLE OF CONTENTS 17. Attach the front of the depth stop assembly to front of center frame assembly bracket with slide plate between bracket and depth stop assembly, depth stop guide on top, limit valve on bottom of bracket with plunger to rear of machine, secure with 5/16 x 5-1/2 bolts and 5/16 lock nuts.
  • Page 44 TABLE OF CONTENTS FRAME SUPPORT PLATE, 7/8 X 11 GR8 BOLTS, 7/8 FLAT WASHERS, 7/8 LOCK NUTS SHANK TUBE PLATE, 3/4 X 6-13/16 X 7-3/4 NOTE: REMOVE THE 3/4 LOCK NUTS U-BOLTS, FROM THE FACTORY INSTALLED 3/4 LOCK NUTS 3/4 X 9 BOLTS AND SHANK MOUNT PLATES SHANK TUBE MOUNT CENTER SHANK MOUNT ASSEMBLY,...
  • Page 45 TABLE OF CONTENTS 7/8 X 7 GR8 BOLTS, MANIFOLD CENTER, 7/8 FLAT WASHERS, 1/2 X 6 BOLTS, FRONT 7/8 LOCK NUTS .75 X .532 X 1.875 RD TUBE, 3/4 X 6-1/2 GR5 BOLTS, 1/2 LOCK NUTS 3/4 FLAT WASHERS, 3/4 LOCK NUTS REAR FOLD PLATES, WING STABILIZER WELDMENT, MANIFOLD REAR FOLD,...
  • Page 46 TABLE OF CONTENTS 1-1/4 X 1 SPACER, 1-5/8 X 1-1/4 X 1 BUSHINGS, 4-1/2 X 16 CYLINDERS, 1-1/4 X 7 PINS, 1-1/4 WASHERS, 5/16 X 2-1/2 SPRING PINS BUSHING, 4-1/2 X 16 CYLINDER SPRING/CLAMP SHANK ASSEMBLY BEARING CAP, 3/4 X 2-1/2 BOLT, DETAIL A 3/4 LOCK NUT DEPTH STOP...
  • Page 47 TABLE OF CONTENTS Table provided for general use. NOTES: 3-13...
  • Page 48 36” tall. 10. After the wings are installed, they will need to be 3. Model 2411-07, attach the LH & RH reel lift leveled to the center frame. The ends of the fold extensions, 3/4 x 8 GR8 bolts, 3/4 x 2-1/2 bolts and cylinders have wrench flats for any small adjustments 3/4 lock nuts.
  • Page 49 TABLE OF CONTENTS 2411-09, 2411-09, 1-1/4 X 7 PIN, 2411-09, LH REEL LIFT EXT, RH REEL LIFT EXT, 5/16 X 2-1/2 SPRING PIN BOLT ON EXT, CLAMP WELDMENT, 3/4 X 8 GR8 BOLTS, 1-1/4 WASHERS 3/4 X 8 GR8 BOLTS,...
  • Page 50 1/2 x 2-1/4 pin and 1 lock See Figure 3-9 for 2411AFG-07-09. See Figure 3-8 for 2411-06 or See Figure 3-9 6. Attach hose clamps to top side of wrench holder plate 2411AFG-07-09. with 3/8 x 3-1/2 bolt, 3/8 flat washer and 3/8 lock nut.
  • Page 51 1/4 LOCK NUT 3/8 FLAT WASHER, 1-1/4 X 9-1/2 GR8 BOLT, 3/8 LOCK NUT 1-1/4 LOCK WASHER, 1-1/4 LOCK NUT HOSE HOLDER BRACKET, 3/4 X 2 BOLT, 3/4 FLAT WASHER, 3/4 LOCK NUT JACK HITCH ASSEMBLY Figure 3-8: Hitch Assembly 2411-06 3-17...
  • Page 52 TABLE OF CONTENTS NOTE: ATTACH REAR OF LEVELER TO CENTER HOLE OF LIFT ASSEMBLY 30” TOWER ASSEMBLY, HITCH PIN, 1/2 X 2-1/4 PIN, 1 LOCK NUT LEVELER ASSEMBLY, DETAIL A HITCH PIN, 1/2 X 2-1/4 PIN, 1-1/2 X 10 GA BUSHINGS, 1 LOCK NUT NOTE: INSTALL BOTTOM OF 30”...
  • Page 53 TABLE OF CONTENTS Table provided for general use. NOTES: 3-19...
  • Page 54 Disc Gang to Wing Frame 1. Remove the 3/4 lock nuts from bottom of wing frame, the 3/4 x 10 bolts, flat washers and gang lift plates Assembly may be left on top side of frames, Model 2411-06 Figures 3-13, Models...
  • Page 55 TABLE OF CONTENTS 1-5/16” 5-5/16” Figure 3-11: Disc Gang Gauge Adjustment 2411-06 NOTE: TO INITIALLY SET GAUGE, ALIGN FRONT OF DEPTH GAUGE MOUNT TO CYLINDER ANCHOR CYLINDER ANCHOR DEPTH GAUGE MOUNT 6-1/4” Figure 3-12: Disc Gang Gauge Adjustment 2411AFG-07-09 3-21...
  • Page 56 RIGHT FRONT 3/4 LOCK NUTS DISC GANG ASSEMBLY GANG LIFT PLATE, 3/4 X 8 BOLT, 3/4 LOCK NUT LEFT REAR LEFT FRONT DISC GANG DISC GANG ASSEMBLY ASSEMBLY Figure 3-13: Disc Gang & Gauge to Frame Installation 2411-06 3-22 F-1130-2304...
  • Page 57 TABLE OF CONTENTS DEPTH GAUGE ARM MOUNT, LINK GAUGE, BUSHING, 1/2 X 1-1/2 BOLTS, 1/2 FLANGE LOCK NUT, 4.937 X 5 U-BOLT, 3/8 LOCK NUT, LEVEL INDICATOR DECAL GAUGE MOUNT, GAUGE MOUNT PLATE, 1/2 X 8-1/2 BOLTS, 1/2 LOCK NUTS GAUGE LEVEL INDICATOR, 1/2 X 1-3/4 SQUARE HEAD BOLT, 1/2 FLAT WASHERS,...
  • Page 58 TABLE OF CONTENTS Shank and Point Installation NOTE The shanks can be positioned in any of the three holes offered. For a maximum depth of 14” the bottom NOTE hole is needed. There is approximately 2” difference The clamp-shank assembly will shipped installed to between the holes.
  • Page 59 TABLE OF CONTENTS CLAMP-SHANK ASSEMBLY 3/4 X 4 BOLT, 3/4 LOCK NUT 5/8 X 3-1/2 GR8 BOLT, 5/8 LOCK NUT SHANK, 3/4 OD X 5/8 ID HARDENED BUSHING NOTE: TORQUE THE 1/2 X 2-3/4 BOLT, GATE CLAMP BOLTS 1/2 FLAT WASHER, TO 300-350 FT/LBS WEAR GUARD, 1/2 LOCK NUT...
  • Page 60 Model 2411-06. See Figure 3-27 for hydraulic disc gang lift assembly Model 2411AFG-07-09. 1. Model 2411-06 install the lift/gang 16 port manifold to the center shank mount plate using 1/2 x 3-1/2 bolts and 1/2 lock nuts See Figures 3-16.
  • Page 61 TABLE OF CONTENTS 4. Models 2411AFG-07-09 install the 8 port manifold to 8 PORT (DISC GANG) MANIFOLD FRONT the front side of the wing stop plate on the center ASSEMBLY, 1/2 X 6 BOLT, frame using 1/2 x 4 bolts, and 1/2 lock nuts .75 X .532 X 1.875 BUSHING, Figures...
  • Page 62 MANIFOLD ASSEMBLY 16 PORT 16 PORT MANIFOLD MANIFOLD ASSEMBLY ASSEMBLY #10 O-RING #10 O-RING X #10JIC ADAPTER X #10JIC ADAPTER .875-14 O-RING 45° ADAPTER 3/4-16 DETAIL A PLUG FRONT VIEW REAR VIEW Figure 3-21: Hydraulic Lift Installation 2411-06 3-28 F-1130-2304...
  • Page 63 TABLE OF CONTENTS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS NOTE: RUN HOSES NOTE: RUN HOSES THROUGH ALL HOSE THROUGH ALL HOSE CLAMPS AND LOOPS CLAMPS AND LOOPS Figure 3-22: Hydraulic Lift Layout 2411-06 3-29...
  • Page 64 TABLE OF CONTENTS 4-1/2 X 16 NOTE: HOSES CONNECT NOTE: HOSES CONNECT CYLINDER FROM SECOND FROM FROM BOTTOM PORT OF MANIFOLD BOTTOM PORT OF MANIFOLD TO ROD END OF TO BASE END OF LIFT CYLINDERS LIFT CYLINDERS 1/2” X 90” HOSE 1/2”...
  • Page 65 TABLE OF CONTENTS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS NOTE: RUN HOSES THROUGH ALL HOSE LOOPS Figure 3-24: Hydraulic Lift Layout 2411AFG-07-09 3-31...
  • Page 66 TABLE OF CONTENTS 3/8” X 31” NOTE: HOSE CONNECTS FROM HOSE TOP PORT OF 16 PORT MANIFOLD TO 3/8” X 33” ROD END OF FOLD LOCK CYLINDER HOSE 3/8” X 27” HOSE 3/8” X 31” NOTE: HOSES CONNECT FROM DETAIL C 1-1/2 X 1-1/2 HOSE TOP PORT OF ALL MANIFOLDS TO...
  • Page 67 TABLE OF CONTENTS NOTE: RUN HOSES NOTE: CYLINDER FITTINGS THROUGH ALL HOSE ARE ALL ON BOTTOM SIDE OF CLAMPS AND LOOPS TO FOLD CYLINDERS DETAIL A FRONT OF MACHINE DETAIL A REAR VIEW NOTE: HOSE ROUTING BETWEEN FRONT AND REAR FOLD TOWER PLATES DETAIL A REAR VIEW...
  • Page 68 FRONT OF MACHINE CYLINDER 16 PORT 16 PORT MANIFOLD MANIFOLD ASSEMBLY ASSEMBLY 3/4-16 PLUG 90° #8 ADAPTER 90° #8 ADAPTER 3/4-16 PLUG 45° #8 ADAPTER DETAIL A FRONT VIEW REAR VIEW Figure 3-27: Hydraulic Gang Lift Installation 2411-06 3-34 F-1130-2304...
  • Page 69 NOTE: LOCATION OF 90° 1/16 RESTRICTOR FITTING NOTE: LOCATION OF 3-3/4 X 8 CYLINDER NOTE: RUN HOSES NOTE: RUN HOSES THROUGH ALL HOSE THROUGH ALL HOSE CLAMPS AND LOOPS CLAMPS AND LOOPS Figure 3-28: Hydraulic Gang Lift Layout 2411-06 3-35...
  • Page 70 TABLE OF CONTENTS 90° 1/16 RESTRICTOR 3/8” X 267” ADAPTER HOSE 90° #8 ADAPTER 3/8” X 146” HOSE 3/8” X 146” HOSE DETAIL A 3/8” X 126” 3/8” X 306” 3-3/4 X 8 HOSE HOSE CYLINDER 3/8” X 126” 3/8” X 306” HOSE HOSE 3/8”...
  • Page 71 TABLE OF CONTENTS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS NOTE: 90° 1/16 RESTRICTOR ADAPTER NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS Figure 3-30: Hydraulic Gang Lift Layout 2411AFG-07-09 3-37...
  • Page 72 TABLE OF CONTENTS Table provided for general use. NOTES: 3-38 F-1130-2304...
  • Page 73 TABLE OF CONTENTS 7-PIN 4-PIN CIRCUIT WIRE COLOR CONN. TOWER GROUND WHITE – WORK LAMPS BLACK LEFT FLASHING YELLOW & TURN – STOP LAMPS RIGHT FLASHING GREEN & TURN TAIL LAMPS BROWN SWITCHED – BLUE POWER (12 V) MAIN WARNING LIGHT HARNESS - WIRING CHART RIGHT RIGHT LEFT...
  • Page 74 1/2 lock nuts See Figure 3-3 SIS DECAL Figure 3-4 after 08-01-2022. 3. Model 2411-06 attach the ag flasher control module to bottom of tail light mount with 1/4 x 1-1/2 bolts, 1/4 lock nuts See Figure 3-32. Attach the reflector mount to top side of the tail light mount, red ag lamp with 1/4 x 1-1/2 bolts 1/4 lock nuts.
  • Page 75 10. Two 34” harnesses are provided if needed for main harness to reach from ag flasher control module to the tractor See Figure 3-36 Model 2411-06 or Figure 3-9 Models 2411AFG-07-09, for location. 11. Insure that the harnesses are clear of any moving...
  • Page 76 FRONT WIRING HARNESS’S CLEAR OF MOVING PARTS NOTE: ROUTE MAIN HARNESS TO FRONT OF MACHINE WITH HYDRAULIC HOSES THROUGH ALL CLAMPS ON HITCH ASSEMBLY 7-PIN CONNECTOR TO TRACTOR STORE- A-WAY HARNESS Figure 3-36: Electrical Assembly W/LED Lights 2411-06 3-42 F-1130-2304...
  • Page 77 THROUGH HOLE AND THROUGH ARM TUBE THROUGH ARM TUBE LIGHT HARNESS LIGHT HARNESS 132” EXTENSION 132” EXTENSION REAR LIGHT MAIN LIGHT HARNESS HARNESS 9” 9” NOTE: AG FLASHER MODULE MOUNTS UNDER TAIL LIGHT MOUNT Figure 3-37: Electrical Layout W/LED Lights 2411-06 3-43...
  • Page 78 TABLE OF CONTENTS 34” HARNESS EXTENSIONS RED AG LAMP AG FLASHER 132” HARNESS CONTROL MODULE NOTE: ROUTE 132” MAIN HARNESS THROUGH HARNESS LIGHT ASSEMBLY BRACKET RT REAR HARNESS AMBER AG 132” HARNESS LAMP FRONT FOLD TOWER PLATE AMBER AG LAMP NOTE: ROUTE 132”...
  • Page 79 TABLE OF CONTENTS NOTE: SECURE LIGHT HARNESSES MAIN LIGHT HARNESS, WITH TIES STRAPS AS NEDDED 7-PIN CONNECTOR TO KEEP CLEAR OF ANY TO TRACTOR MOVING PARTS NOTE: ROUTE LIGHT HARNESS THROUGH ALL HOSE LOOPS AND CLAMPS ALONG HYDRAULIC HOSES NOTE: ROUTE 132” LIGHT HARNESS EXTENSION DOWN NOTE: ROUTE 132”...
  • Page 80 1/2 flat washer, 1/2 lock nut, the hose clamp attaches with 3/8 x 1-1/2 bolt, 3/8 flat washer, 3/8 lock nut. 9. Models 2411-06 install the 8 port manifold to rear of Figure 3-41: #8JIC Bulkhead 90° Adapter Installation manifold/smv mount assembly with 1/2 x 5-1/2 bolts,...
  • Page 81 TABLE OF CONTENTS 11. Models 2411AFG-07-09 install the 8 port manifold to 13. Install the mount plate to both inner combo harrow rear fold tower assembly with 1/2 x 10 bolts, 1/2 lock mount arm with 1/2 x 6 bolt, 1/2 flat washer and 1/2 nuts as shown See Figures 3-42.
  • Page 82 TABLE OF CONTENTS HARROW ADJ WRENCH, QUICK HITCH PIN MOUNT PLATE, HOSE CLAMP, 3/8 X 1-1/2 BOLT, BULKHEAD TEE, 1/2 X 6 BOLT, 3/8 FLAT WASHER, 3/8 LOCK NUT 1/2 FLAT WASHER 1/2 LOCK NUT HYD COMBO ARM LONG NOTE: WRENCH MOUNT ASSEMBLY USED ON LEFT CENTER FRAME ARM ASSEMBLY ONLY, HOSE MOUNT ASSEMBLY USED ON HYDRAULIC...
  • Page 83 TABLE OF CONTENTS Table provided for general use. NOTES: 3-49...
  • Page 84 CYLINDER HOSE NOTE: TOP SET OF HOSES GOES TO BASE END OF CYLINDERS 90° #8 ADAPTER #8 PLUG #6 BULKHEAD #6 BULKHEAD #6 X #8 ADAPTER DETAIL A DETAIL C DETAIL B Figure 3-45: 3BCT/Chopper Hydraulic Installation 2411-06 3-50 F-1130-2304...
  • Page 85 TABLE OF CONTENTS Figure 3-1: 3BCT/Chopper Hydraulic Layout 2411-06 3-51...
  • Page 86 TABLE OF CONTENTS FRONT OF MACHINE TO TRACTOR 3/4 O-RING ADAPTER 1/4 X 84 HOSE (2411-07) 1/4 X 112 HOSE (2411-09) RED HOSE WRAP 1/4 X 88 HOSE (2411-07) 1/4 X 116 HOSE (2411-09) 1/4 X 22 3/8 X 466...
  • Page 87 TABLE OF CONTENTS NOTE: RUN HOSES THROUGH HITCH HOSE LOOPS AND CLAMPS TO TRACTOR NOTE: RUN HOSES THROUGH NOTE: RUN HOSES SLOTTED HOLES OF ARMS THROUGH ALL HOSE TO CYLINDER FITTINGS CLAMPS AND LOOPS Figure 3-2: 3BCT/Chopper Hydraulic Layout 2411AFG-07-09 3-53...
  • Page 88 TABLE OF CONTENTS Disc Lev/Hyd Flat RL Installation #6 JIC HOSE CLAMP, 3/8 X 1-1/2 BOLT, BULKHEAD (Option) 3/8 FLAT WASHER, 3/8 LOCK NUT Refer to See Figures 2-8 through See Figures 2-10 disc lev/hyd flat rl placement. HOSE MOUNT PLATE, BULKHEAD HOSE MOUNT PLATE, NOTE...
  • Page 89 TABLE OF CONTENTS 16. Install the hose mount plate to both outer no/hyd arm NOTE with 1/2 x 8-1/2 bolt, 1/2 flat washer, 1/2 lock nut. Note locations of hose clamps, hose mount plates Attach hose clamp with the 3/8 x 1-1/2 bolt, the hose and bulkhead mount plates and bulkhead tees clamp with 3/8 x 1-1/2 bolt, 3/8 flat washer, 3/8 lock Figure 3-52...
  • Page 90 TABLE OF CONTENTS LEVELER MOUNT ASSEMBLY O-RING, DISC BLADE, 5/8 X 1-1/4 BOLTS, 3/4 X 8-1/2 BOLTS, 5/8 LOCK WASHER 3/4 FLAT WASHERS, 3/4 LOCK NUT BULKHEAD BULKHEAD MOUNT PLATE, 1/2 X 8-1/2 BOLT, 1/2 FLAT WASHER, 1/2 LOCK NUT 3-1/4 HYD ARM ASSEMBLY DISC LIFT TUBE...
  • Page 91 NOTE: DISC LEVELER HOSES CONNECT TO TOP 2 SET OF PORTS AND REEL BLACK HOSE WRAP STR #8 X #8 ASSEMBLIES CONNECT TO BOTTOM 1/4 X 98 HOSE (2411-07) 2 SET OF PORTS UNION 3/8 X 36 1/4 X 120 HOSE (2411-09)
  • Page 92 TABLE OF CONTENTS NOTE: ROUTE HOSES THROUGH LOOPS AND CLAMPS TO NOTE: ROUTE TRACTOR HOSES THROUGH NOTE: LOCATION LOOPS BETWEEN OF BLACK HOSE FOLD PLATES WRAPS NOTE: LOCATION OF 3-1/2 HYD ARM ASSEMBLY NOTE: LOCATION NOTE: LOCATION OF NOTE: LOCATION OF OF 3-1/4 HYD ARM NO/HYD ARM ASSEMBLY NO/HYD ARM ASSEMBLY...
  • Page 93 TABLE OF CONTENTS NOTE: LOCATION OF HOSE MOUNT PLATES NOTE: LOCATION OF BULKHEAD MOUNT PLATES NOTE: LOCATION NOTE: LOCATION AND BULKHEAD TEE FITTINGS OF 90° 1/16 OF 90° 1/16 RESTRICTOR ELBOW RESTRICTOR ELBOW NOTE: RUN HOSES THROUGH SLOTTED HOLES OF ARMS TO CYLINDER FITTINGS Figure 3-53: Disc Lev/Hyd RL Layout 2 2411AFG-07-09 3-59...
  • Page 94 “Hydraulic Fold System 2411AFG-2411-07-09” on page 4-4. 4. Connect lights to the tractor and verify operation. 5. Check tires for proper inflation 6. Level the Weatherproofer from front to rear as described “Leveling...
  • Page 95 DANGER DANGER DANGER DANGER Never allow anyone to ride on the 2411 When transporting the unit, place cylinder Weatherproofer at any time. Allowing a person to lockouts in the transport lock position after fully ride on the machine can inflict serious personal extending the cylinders.
  • Page 96 3. Clean all hydraulic couplings and attach to the tractor. 4. Fully extend the hydraulic lift wheel cylinders, and 1. Prior to operating the 2411 Weatherproofer, inspect it place the cylinder lockouts in the transport lock thoroughly for good operating condition.
  • Page 97 TABLE OF CONTENTS Hydraulic Lift System 2. The hydraulic system is not filled with oil and should be purged of air before transporting and field The Weatherproofer is equipped with a hydraulic lift operations. Carefully hitch the Weatherproofer to the system to raise and lower the unit in the field.
  • Page 98 5. The hydraulic fold system has an automatic wing lock cylinder in the system See Figure 4-4. This small 2411AFG-2411-07-09 cylinder is in the center of the machine and will work opposite of the wing fold cylinders. Verify that when 1. Models 2411AFG-07-09 Weatherproofer equipped the wing fold cylinders are retracting that this 1-1/2”...
  • Page 99 TABLE OF CONTENTS TRANSPORT LOCK HOOKS TRANSPORT LOCK PIN WING LOCK CYLINDER TRANSPORT LOCK PIN Figure 4-4: Automatic Wing Lock 2411AFG-07-09...
  • Page 100 TABLE OF CONTENTS General Operation Leveling (Front-to-Rear) 1. The horsepower requirements are typically 40-50 NOTE horsepower per shank. This will vary widely due to speed, depth, moisture, residue and types of soils. The Weatherproofer will have to be field leveled for Local dealers can help in making recommendations optimum performance.
  • Page 101 TABLE OF CONTENTS Disc Blades Depth Stop Adjustment 1. The 2411 Weatherproofer is equipped with 24" or 26” The operating depth of the Weatherproofer is controlled disc blades. by a single-point depth stop. The stop is located at the center front of the machine.
  • Page 102 1.5 times the BOTH SIDES SIS 20MPH DECAL tractor weight. Figure 4-9: SIS 20MPH Decal Front 2411-06 3. A safety chain is provided with the implement to insure safe transport. a.The safety chain should have a tensile strength equal to or greater than the gross weight of the implement.
  • Page 103 4-13. TRANSPORT LOCK STORED POSITION LIGHT BRACKET ASSEMBLY REAR SIS MOUNT SIS 20MPH DECAL Figure 4-11: SIS 20MPH Decal Rear 2411-06 L PIN, 1/8 HAIRPIN TRANSPORT LOCK INSTALLED POSITION REAR FOLD TOWER PLATE SIS 20MPH DECAL Figure 4-13: Transport Locks...
  • Page 104 5. Re-install the 1 x 7-5/16 pins, 3/16 dia pins through direct contact. aligned holes of harrow arm assemblies. 6. Reels are set to 21-1/2” from Landoll. To adjust the standard reel height, loosen the locking hex nut 3. The coil tine harrow should run level with the coulter...
  • Page 105 TABLE OF CONTENTS MORE LESS AGGRESSIVE AGGRESSIVE HARROW HEIGHT ANGLE JAM NUT ADJUSTMENT HOLES ADJUSTMENT SPRING PLATE ASSEMBLY HARROW ARM 21-1/2 ASSEMBLY HARROW 1 X 7-5/16 PIN, REEL ADJUSTMENT 3/16 DIA HAIR PIN ASSEMBLY 1/2 X 1-1/4 RD HEAD SQ NECK SCREW HARROW HEIGHT HARROW HEIGHT...
  • Page 106 TABLE OF CONTENTS Disc Lev/Hyd Flat RL Adjust- NOTE ments Model 2411-06 uses 1 set of 1P332 cylinder stops and Models 2411AFG-07-09 uses 2 sets. 1. The optional Disc Leveler/Hydraulic Flat Reel 5. Cylinder stops have been provided to maintain depth attachment consists of independent disc assemblies position.
  • Page 107 TABLE OF CONTENTS NOTE: LOCATION OF 1P332 CYLINDER STOP 2411-06 NOTE: LOCATION OF 1P332 CYLINDER STOP 2411AFG-07-09 Figure 4-16: Disc Lev/Hyd Flat RL Cylinder Stop Location 4-13...
  • Page 108 TABLE OF CONTENTS JAM NUT SPRING ASSEMBLY 21-1/2’ REEL ASSEMBLY SPRING ASSEMBLY REEL ASSEMBLY Figure 4-17: Disc Lev/Hyd Flat RL Adjustments 4-14 F-1130-2304...
  • Page 109 TABLE OF CONTENTS Chapter 5 Maintenance and Lubrication Wheel Bearing Maintenance -- 9. Tighten the slotted nut while rotating the hub until there is a slight resistance to wheel rotation. Then, Triple-Lip back the slotted nut off one notch, until the wheel rotates freely without end play.
  • Page 110 Table 5-1 specifies the lubrication points and intervals Regular lubrication will maintain a full grease cavity on the 2411. Proper maintenance of your machine and help purge any contaminants. Grease the will, under normal operating conditions, help to keep bearings before long periods of storage to prevent it operating at or near its peak performance for an moisture buildup within the bearing cavity.
  • Page 111 2. Store the unit in a shed or under a tarpaulin to protect it from the weather. The ground tools and tires should 1. The service life of the 2411 Weatherproofer will be rest on boards, or some other object, to keep them extended by proper off-season storage practices.
  • Page 112 TABLE OF CONTENTS Table provided for general use. NOTES: F-1130-2304...
  • Page 113 Chapter 6 Troubleshooting Guide The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 2411 Weatherproofer. Follow all safety precautions stated in the previous sections when making any adjustments to your machine. PROBLEM...
  • Page 114 TABLE OF CONTENTS Table provided for general use. NOTES: F-1130-2304...
  • Page 115 Document Control Revision Log: Date Form # Improvement(s): Description and Comments 03/24/2022 F-1130 New manual 06/17/2022 F-1130-0622 Initial release 04/21/2023 F-1130-2304 Added model 2411-06, added disc lev/hyd rl attachment, updated 2411AFG-07-09 center frame, updated shank assembly...
  • Page 116 Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Model 2411 Weatherproofer Operators Manual Re-order Part Number F-1130 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...