1. Manuals
  2. Brands
  3. Landoll Manuals
  4. Farm Equipment
  5. 2131
  6. Operator's manual

Landoll 2131 Operator's Manual

Wing coulter chisel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Model 2131
Wing Coulter Chisel
Operator's Manual
LANDOLL CORPORATION
1900 North Street
Marysville, Kansas 66508
(785) 562-5381
800-428-5655 ~ WWW.LANDOLL.COM
F-721-0513

Advertisement

Table of Contents
loading

Related Manuals for Landoll 2131

Summary of Contents for Landoll 2131

  • Page 1 Model 2131 Wing Coulter Chisel Operator’s Manual LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-721-0513...

  • Page 3: Table Of Contents

    Table of Contents Introduction Understanding Safety Statements ..........1-2 Standard Specifications Model Specifications .
  • Page 4 Hydraulic Lift System ............4-2 Hydraulic Fold System .

  • Page 5: Introduction

    Chapter 1 Introduction The Landoll Model 2131 Wing Coulter Chisel is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation CHAPTER 1 gives basic instructions on the use of this manual.

  • Page 6: Understanding Safety Statements

    Make sure you read and understand the information contained in this manual and on the machine signs (decals) before you attempt to operate or maintain this vehicle. The safety statements contained in this manual relate to the operation of the Model 2131 Wing Coulter Chisel. F-721-0513...

  • Page 7: Standard Specifications

    Chapter 2 Standard Specifications Model Specifications 2131 Series Wing Coulter W/Auto Reset Shanks Model Number 2131-17 2131-19 2131-21 2131-23 2131-25 Working Width 21'-3” 23'-9” 26'-3” 28'-9” 31'-3” Transport Width 16'-1” 16'-1” 15'-6” 15'-6” 15'-6” Transport Height 11'-1” 11'-7” 13'-5” 13'-11”...
  • Page 8 STANDARD SPECIFICATIONS Tire Inflation Tire Size Tire Manufacturer Ply/Load Rating Inflation Pressure (Psi) (Max.) 12.5L x 15 Firestone 12 Ply/3860 lbs. 52 psi. 32/1550 x 16.5 Galaxy G Load 8000 lbs. @ 20 mph 115 psi. 380/55R-16.5 Goodyear Load Index 150A8/B7400 lbs. @ 30 mph 73 psi.

  • Page 9: General Torque Specifications (Rev. 4/97)

    STANDARD SPECIFICATIONS General Torque Specifications (rev. 4/97) TORQUE SPECIFIED IN FOOT POUNDS - This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).

  • Page 10: Hydraulic Fitting Torque Specifications

    STANDARD SPECIFICATIONS Hydraulic Fitting Torque Specifications TORQUE IS SPECIFIED IN FOOT POUNDS- 37 JIC, ORS, & ORB (REV. 10/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).
  • Page 11 STANDARD SPECIFICATIONS Table provided for general use. NOTES:...
  • Page 12 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 4-1/4” 4-1/4” 5” 5” 5” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 2130-17 shank-light placement Figure 2-1: Auto Reset Shank and Light Bracket Placement (2131-17) F-721-0513...
  • Page 13 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5-1/8” 4-1/4” 4-1/4” 5” 5” 5” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 2130-17_rsb shank-light placement Figure 2-2: Rigid Shear Shank and Light Bracket Placement (2131-17)
  • Page 14 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 4-1/4” 4-1/4” 5” 5” 5” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 4-7/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 4-7/8” 2130-19 shank-light placement Figure 2-3: Auto Reset Shank and Light Bracket Placement (2131-19) F-721-0513...
  • Page 15 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5-1/8” 4-1/4” 4-1/4” 5” 5” 5” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 4-7/8” 4-7/8” 2130-19_rsb shank-light placement Figure 2-4: Rigid Shear Shank and Light Bracket Placement (2131-19)
  • Page 16 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5” 4-1/4” 5-1/8” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 2130-21 shank-light placement p1 Figure 2-5: Auto Reset Shank and Light Bracket Placement (2131-21) 2-10 F-721-0513...
  • Page 17 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 4-1/4” 5-1/8” 5” 5-1/8” 5” 20-1/8” LT RT 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/2” 2130-21 shank-light placement p2 Figure 2-6: Auto Reset Shank and Light Bracket Placement (2131-21) 2-11...
  • Page 18 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5” 5-1/8” 5-1/8” 5-1/8” 4-1/4” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 2130-21_rsb shank-light placement p1 Figure 2-7: Rigid Shear Shank and Light Bracket Placement (2131-21) 2-12 F-721-0513...
  • Page 19 STANDARD SPECIFICATIONS NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5” 5-1/8” 5-1/8” 4-1/4” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/2” 2130-21 shank-light placement p2 Figure 2-8: Rigid Shear Shank and Light Bracket Placement (2131-21) 2-13...
  • Page 20 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5” 4-1/4” 5-1/8” 5” 20-1/8” 5-1/8” LT RT 5-1/8” 5-1/8” 5-1/8” 4-7/8” 5-1/8” 5-1/8” 5-1/8” 2130-23 shank-light placement p1 Figure 2-9: Auto Reset Shank and Light Bracket Placement (2131-23) 2-14 F-721-0513...
  • Page 21 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 4-1/4” 5-1/8” 5” 5-1/8” 5” 20-1/8” LT RT 5-1/8” 5-1/8” 5-1/8” 4-7/8” 5-1/8” 5-1/8” 5-1/2” 2130-23 shank-light placement p2 Figure 2-10: Auto Reset Shank and Light Bracket Placement (2131-23) 2-15...
  • Page 22 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5” 5-1/8” 5-1/8” 5-1/8” 4-1/4” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 4-7/8” 2130-23_rsb shank-light placement p1 Figure 2-11: Rigid Shear Shank and Light Bracket Placement (2131-23) 2-16 F-721-0513...
  • Page 23 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5” 5-1/8” 5-1/8” 4-1/4” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/2” 4-7/8” 2130-23 shank-light placement p2 Figure 2-12: Rigid Shear Shank and Light Bracket Placement (2131-23) 2-17...
  • Page 24 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5” 4-1/4” 5-1/8” 5-1/8” 4-3/4” 5” 5-1/8” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 4-7/8” 2130-25 shank light placement p1 Figure 2-13: Auto Reset Shank and Light Bracket Placement (2131-25) 2-18 F-721-0513...
  • Page 25 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5” 5-1/8” 5-1/8” 4-1/4” 4-3/4” 5” 5-1/8” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/2” 4-7/8” 2130-25 shank light placement p2 Figure 2-14: Auto Reset Shank and Light Bracket Placement (2131-25) 2-19...
  • Page 26 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5” 5-1/8” 5-1/8” 5-1/8” 4-1/4” 5” 4-3/4” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 4-7/8” 2130-25_rsb shank-light placement p1 Figure 2-15: Rigid Shear Shank and Light Bracket Placement (2131-25) 2-20 F-721-0513...
  • Page 27 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5” 5-1/8” 5-1/8” 4-1/4” 5” 4-3/4” 20-1/8” 4-7/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/2” 2130-25 _rsb shank light placement p2 Figure 2-16: Rigid Shear Shank and Light Bracket Placement (2131-25) 2-21...
  • Page 28 114” REEL 82” REEL ASSEMBLY ASSEMBLY ASSEMBLY 2130-17 30-1/2 91” REEL 114” REEL 91” REEL ASSEMBLY ASSEMBLY ASSEMBLY 2130-19 2130-17 & 19 chopper reel placement Figure 2-17: Standard and Hydraulic Tubular Mount Chopper Reel Placement (2131-17 & 2131-19) 2-22 F-721-0513...
  • Page 29 114” REEL ASSEMBLY ASSEMBLY 114” REEL ASSEMBLY 2130-21 3-1/2 3-1/2 3-1/2 129” REEL 129” REEL 30-1/2 ASSEMBLY ASSEMBLY 114” REEL ASSEMBLY 2130-23 2130-21& 23 chopper reel placement Figure 2-18: Standard and Hydraulic Tubular Mount Chopper Reel Placement (2131-21 & 2131-23) 2-23...
  • Page 30 ATTACH TO RIGID SHEAR SHANK MODELS USING SAME DIMENSIONS. 3-1/2 3-1/2 3-1/2 53-1/4 53-1/4 129” REEL 129” REEL ASSEMBLY ASSEMBLY 129” REEL ASSEMBLY 2130-25 2130-25 chopper reel placement Figure 2-19: Standard and Hydraulic Tubular Mount Chopper Reel Placement (2131-25) 2-24 F-721-0513...
  • Page 31 STANDARD SPECIFICATIONS 7-1/2 5-1/2 7-1/2 7-3/4 28-1/4 27-3/4 2130-17 6-1/2 3-1/2 6-1/2 2130-19 Figure 2-20: Coil Tine Harrow Placement (2131-17 & 2131-19) 2-25...
  • Page 32 STANDARD SPECIFICATIONS 5-1/2 5-1/2 5-1/2 5-3/4 2130-21 5-1/2 3-1/2 5-1/2 4-7/8 2130-23 Figure 2-21: Coil Tine Harrow Placement (2131-21 & 2131-23) 2-26 F-721-0513...
  • Page 33 STANDARD SPECIFICATIONS 3-1/2 3-1/2 3-1/2 7-7/8 19-7/8 7-1/4 90-1/4 90-1/4 2130-25 Figure 2-22: Coil Tine Harrow Placement (2131-25) 2-27...
  • Page 34 STANDARD SPECIFICATIONS 2-28 F-721-0513...

  • Page 35: Assembly Instructions

    Chapter 3 Assembly Instructions It is very important that your new 2131 Wing Coulter  WARNING Chisel be properly assembled, adjusted and lubricated before use. Illustrations to assist with the assembly Do not attempt to lift heavy parts (such as the process are provided in “Standard Specifications”...
  • Page 36 HITCH PIN HEAD CAP HEX HEAD CAP SCREW SCREW 1-8 HEX LOCK NUT HOSE HOLDER HITCH WELDMENT BRACKET HITCH RING SAFETY 1N FLAT WASHER CHAIN 1-8 HEX LOCK NUT 2131 hitch assy op Figure 3-1: Hitch Installation (w/o Weights) F-721-0513...
  • Page 37 ASSEMBLY INSTRUCTIONS HITCH CLAMP 1/4 ZERK FITTING 3/4-10 HEX LOCK NUT 1-3/4-5 LH HEX JAM NUT WEIGHT LOCK PLATE LH RADIUS ROD SCREW ASSEMBLY HITCH WEIGHT 1/4 X 1-3/4 ROLL PIN HITCH RADIUS ROD 1-3/4-5 HEX JAM NUT 1-1/4 SLOTTED LOCK WASHER 1-1/4-7 HEX NUT...

  • Page 38: Wing Coulter Chisel Center Frame Assembly

    ASSEMBLY INSTRUCTIONS Wing Coulter Chisel Center 5. Install a 3/8-16 x 3-1/2 all-thread screw in the front of the hose holder bracket and secure with a 3/8-16 hex Frame Assembly nut. 6. Slide the hose holder clamp over the 3/8” screw and ...
  • Page 39 DEPTH STOP GUIDE DEPTH STOP HANDLE 3/8-16 HEX LOCK NUT SLIDE VALVE MOUNT PLATE (WELDED TO FRAME) STRAIGHT ADAPTER 90 ELBOW FRAME ASSEMBLY 5/16-18 HEX LOCK NUT LIMIT VALVE 2131 depth stop tube assy op Figure 3-3: Depth Stop Assembly Installation...

  • Page 40: Depth Stop Tube Assembly

    ASSEMBLY INSTRUCTIONS Depth Stop Tube Assembly 3. Insert 90 elbow fittings in the back of the limit valve and a straight adapter in the side nearest the center 1. Attach the depth stop mount plate to the shank lift of the machine. using 3/8-16 x 1-1/4 hex head cap screws and hex 4.
  • Page 41 ASSEMBLY INSTRUCTIONS NOTE: FRONT FOLD CYLINDER FITTINGS SHOULD FACE THE REAR OF THE MACHINE. REAR FOLD CYLINDER FITTINGS SHOULD FACE THE FRONT OF THE MACHINE. FITTINGS 5-16 x 2-1/2 SPRING SLOTTED PIN 4 X 30 HYDRAULIC FOLD PIN CYLINDER REAR FOLD ANCHOR FRONT FOLD ANCHOR (USED ON ALL (USED ON 2130-21,...

  • Page 42: Center Frame Tires

    The rear fold cylinder fittings should face the front of the machine. 4. On the 2131-21, 2131-23, and 2131-25 models, attach the bolt-on hinges to the right and left sides of the center frame using 3/4-10 x 6-1/2 hex head cap screws, hinge base plate, and 3/4-10 hex lock nuts (See Figure 3-4.)
  • Page 43 ASSEMBLY INSTRUCTIONS RIGHT WING FRAME ASSEMBLY 4 X 16 SLAVE 1 HYDRAULIC CYLINDER 90 ADAPTERS 1/2 X 2-1/4 GROOVED ALLOY PIN HITCH PIN 1-1/2 THRUST WASHER (INSTALL TO FRONT SIDE) 1-8 HEX LOCK NUTS 5/16 X 2-1/2 SPRING SLOTTED PIN FOLD PIN 4 X 30 HYDRAULIC CYLINDER 3/16 HAIR PIN...

  • Page 44: Wing Frame Installation

    5/16 x 2-1/2 spring slotted pins. 1. On 2131-17 and 2131-19 models, attach right and 4. Install 4-1/2 x 16 hydraulic cylinders to the cylinder left wing frame assemblies to the center frame...
  • Page 45 ASSEMBLY INSTRUCTIONS 3-1/4 X 8 SLAVE 3 HYDRAULIC CYLINDER FRAME AND WING ASSEMBLY 90 ELBOW W/ RESTRICTOR RIGHT WING COULTER GANG ASSEMBLY ADAPTER SLAVE HYDRAULIC CYLINDER ADAPTER COULTER SPRING RIGHT CENTER ROD ASSEMBLY COULTER GANG ROLL PIN ASSEMBLY STEEL BUSHING CLEVIS PIN 3-3/4 X 8 SLAVE 1 90 ADAPTER...

  • Page 46: Coulter Gang Installation

    ASSEMBLY INSTRUCTIONS Coulter Gang Installation 3. Attach the base end of the 3-3/4 x 8 slave 1 cylinder to the coulter spring rod assembly attached to the left center frame weldment using the clevis pins and roll  DANGER pins which come with the cylinder and a steel bushing.
  • Page 47 ASSEMBLY INSTRUCTIONS CLAMP ASSEMBLY 3/4-10 HEX LOCK NUT 1-1/4 X 2-1/2 X 32 50 SHANK 3/4-10 X 5 HEX HEAD CAP SCREW 2 X 1 X 18 SPIKE 1/2-13 X 3 HEX 3/4-10 X 4 HEAD CAP HEX HEAD SCREW CAP SCREW 1/2 HEAVY HEX NUT...

  • Page 48: Auto Reset Shank And Shovel Installation

    ASSEMBLY INSTRUCTIONS Auto Reset Shank and Shovel 2. Install 2 x 1 x 18 spikes or 1/2 x 4 x 26 twisted shovels onto shanks as follows: Installation a. Connect 2 x 1 x 18 spike to each shank using 1/2-13 x 3 hex head cap screws, flat washers, 1.
  • Page 49 ASSEMBLY INSTRUCTIONS SHEAR BOLT CLAMP 12” OFFSET SHEAR BOLT CLAMP 5/8-11 HEX LOCK NUT 3/4-10 HEX LOCK NUT 1-1/4 X 2-1/2 X 32 50 SHANK 5/8-11 X 5-1/2 HEX HEAD CAP SCREW 3/4-10 X 4 HEX HEAD CAP SCREW 2 X 1 X 18 SPIKE 1/2-13 X 3 HEX HEAD CAP SCREW...

  • Page 50: Rigid Shear Shank And Shovel Installation

    5/8 x 3/4 x 1-1/4 connex bushings shown in the hand shovels. drawing are installed at the landoll corporation. IMPORTANT Right and left twisted shovels are determined by direction of dirt flow when facing the direction of travel.
  • Page 51 ASSEMBLY INSTRUCTIONS DEPTH INDICATOR GAUGE W/ DECAL DEPTH GAUGE GUIDE 5/8-11 x 6-11/16 x 5-1/2 1/2-13 HEX U-BOLT LOCKNUT /8-11 FLANGE HEAD SERRATED DEPTH GAUGE MOUNT 1/2-13 X 5 HEX HEAD CAP SCREW 5/8-11 x 6-11/16 x 7-1/2 U-BOLT 2130 depth gauge inst Figure 3-10: Depth Gauge Installation 3-17...

  • Page 52: Depth Gauge Installation

    ASSEMBLY INSTRUCTIONS Depth Gauge Installation NOTE The depth gauge assembly is attached to the coulter gang tube and front frame tube and may be placed at the discretion of the operator. 1. Attach depth gauge guide to the front frame tube using 5/8-11 x 6-11/16 x 5-1/2 u-bolt and flange head serrated nuts (See Figure 3-10.) 2.
  • Page 53 ASSEMBLY INSTRUCTIONS 1/2-13 HEX LOCK NUT 8 PORT MANIFOLD (USED ON ALL MODELS) 1/2-13 X 3-1/2 HEX HEAD CAP SCREW 8 PORT MANIFOLD (USED ON 2130-21, 2130-23, AND 2130-25 MODELS ONLY) 16 PORT MANIFOLD (USED ON ALL MODELS) hydraulic manifold placement Figure 3-11: Shank and Shovel Installation 3-19...

  • Page 54: Hydraulic Installation

    Figure 3-11.) 10. Install hose wraps around system hoses per hose 3. On 2131-21, 2131-23, and 2131-25 models, install identification decal near hose couplers, putting both second 8 port manifold to the manifold bracket on the hoses inside wrap(See Figure 3-12.)
  • Page 55 3/8 X 105 HOSE ASSEMBLY 90 ADAPTER 3-1/4 X 8 REPHASE HYDRAULIC CYLINDER 3/8 X 312 HOSE ASSEMBLY SLAVE 3 90 ADAPTER 90 ELBOW W/ RESTRICTOR 2131-17 19 coulters op Figure 3-13: Coulter Lift Hydraulic Installation (2131-17 & 2131-19) 3-21...
  • Page 56 3/8 X 130 HOSE ASSEMBLY 90 ADAPTER 3-1/4 X 8 REPHASE HYDRAULIC CYLINDER 3/8 X HOSE ASSEMBLY SLAVE 3 90 ADAPTER 90 ELBOW W/ RESTRICTOR 2131 21-25 coulters op Figure 3-14: Coulter Lift Hydraulic Installation (2131-21, 2131-23, & 2131-25) 3-22 F-721-0513...
  • Page 57 MASTER DECAL 90 ADAPTER 4 X 16 REPHASE HYDRAULIC 3/8 X 120 HOSE CYLINDER ASSEMBLY SLAVE 90 ADAPTER SLAVE DECAL FRONT ADAPTER OF MACHINE PLUG PORTS B,G,H,K,L,&M 2131 17-19 lift op Figure 3-15: Wheel Lift Hydraulic Installation (2131-17 & 2131-19) 3-23...
  • Page 58 90 ADAPTER 4 X 16 REPHASE HYDRAULIC 3/8 X 146 HOSE CYLINDER ASSEMBLY SLAVE 90 ADAPTER SLAVE DECAL FRONT ADAPTER OF MACHINE PLUG PORTS B,G,H,K,L,&M 2131 21-25 lift op Figure 3-16: Wheel Lift Hydraulic Installation (2131-21, 2131-23, & 2131-25) 3-24 F-721-0513...
  • Page 59 3/8 X 24 HOSE FOLD PIN ASSEMBLY 1-1/4N FLAT WASHER 90 ELBOW W/ RESTRICTOR 5/16 X 2-1/2 SPRING SLOTTED PIN FRONT OF MACHINE PLUG PORTS E & F 2131 17-19 fold hyd Figure 3-17: Fold Hydraulic Installation (2131-17 & 2131-19) 3-25...
  • Page 60 3/8 X 24 HOSE 90 ELBOW W/ ASSEMBLY RESTRICTOR FOLD PIN 4 X 30 HYDRAULIC 1-1/4N FLAT CYLINDER WASHER 5/16 X 2-1/2 SPRING SLOTTED PIN FRONT OF MACHINE 2131 21-25 fold hyd Figure 3-18: Fold Hydraulic Installation (2131-21, 2131-23, & 2131-25) 3-26 F-721-0513...
  • Page 61 ASSEMBLY INSTRUCTIONS MAIN WARNING LIGHT HARNESS REAR WARNING LIGHT HARNESS ORANGE STRIPE YELLOW REFLECTOR LH LIGHT BRACKET (FRONT OF BRACKET) 1/2-13 X 8-1/2 HEX #8-32 X 1/2 SLOT HEAD CAP SCREW PAN HEAD SCREW 1/4-20 X 1-1/4 HEX ENHANCED HEAD CAP SCREW LIGHTING MODULE 1/4-20 HEX LOCK...

  • Page 62: Light Installation (Prior To August, 2013)

    ASSEMBLY INSTRUCTIONS NOTE: IF REPAIRING OR REPLACING THE 7 PIN CONNECTOR, MATCH THE LETTERS AT THE BACK OF THE HARNESS TO THE 7 PIN CONNECTOR WIRING CHART AS SHOWN. THE COLOR OF THE WIRE JACKET DOES NOT NECESSARILY MATCH THE COLOR 7-PIN 4-PIN MARKING OF THE 7 PIN CONNECTOR.
  • Page 63 ASSEMBLY INSTRUCTIONS FRONT OF MACHINE HARNESS STOR-AWAY W/ 1/4-20 X 3/4 HEX HEAD CAP SCREWS AND HEX LOCK NUT MAIN WARNING LIGHT HARNESS REAR WARNING LIGHT HARNESS 34” EXTENSION HARNESS 1/4-20 HEX LOCK LH LIGHT BRACKET W/ REFLECTORS U-BOLT 5/8-11 FLANGE HEAD SERRATED TAIL LIGHT MOUNT...

  • Page 64: Led Light And Smv Bracket Installation (After August, 2013)

    ASSEMBLY INSTRUCTIONS WIRE DESIGNATIONS FOR MAIN HARNESS WIRE DESIGNATIONS FOR REAR HARNESS 7-PIN 4-PIN CIRCUIT WIRE CONN TOWER COLOR 2-PIN 3-PIN 6-PIN 3-PIN 2-PIN TOWER TOWER SHROUD TOWER TOWER GROUND GROUND WORK LAMPS BLACK LEFT FLASHING YELLOW & TURN STOP LAMPS RIGHT FLASHING GREEN &...

  • Page 65: Final Assembly

    ASSEMBLY INSTRUCTIONS 10. Touch up with paint any areas that may have been scratched during moving, handling, or assembly. 11. Thoroughly read and understand the operating section before using the Coulter Chisel. POUNDS 4 FOOT PULL torque ft lbs Figure 3-23: 1,200 Foot-Pounds of Torque Final Assembly 1.
  • Page 66 ASSEMBLY INSTRUCTIONS 7-3/4” REAR TOW HITCH - SHORT ARM 11-3/4” REAR TOW HITCH - LONG ARM 2130 rear tow hitch placement Figure 3-24: Rear Tow Hitch Placement (Option) 3-32 F-721-0513...

  • Page 67: Rear Tow Hitch Installation (Option)

    ASSEMBLY INSTRUCTIONS 5/8-11 X 9-1/2 HEX HEAD CAP SCREW GR5 REAR HITCH ARM REAR TOW HITCH ASSEMBLY REAR HITCH ARM W/ HOSE LOOPS 5/8-11 HEX LOCK NUT GRB 3/4-10 HEX LOCK NUT GRB REAR HITCH CLAMP PLATE 3/4-10 X 2-1/2 HEX HEAD CAP SCREW m148332 op Figure 3-25: Rear Tow Hitch Installation (Option)
  • Page 68 SUPPORT PLATE 3/4-10 HEX LOCK NUT REEL/GANG GANG BAR BAR ASSEMBLY MOUNT PLATE 3/4-10 X 6 HEX HEAD CAP SCREW 2131 bolt over frame chopper reel assy op Figure 3-26: Standard or Hydraulic Tubular Mount Chopper Reel Installation (Option) 3-34 F-721-0513...

  • Page 69: Standard Tubular Mount Chopper Reel Installation (Option)

    ASSEMBLY INSTRUCTIONS Standard Tubular Mount Chopper 3/16 HAIR PIN Reel Installation (Option) 1/4 X 2-1/2 1. Slide chopper reel arm assemblies over rear frame SLOTTED bar using chopper reel placement drawings (See ROLL PIN Figures 2-17, 2-18, 2-19, and 3-26.) 2.
  • Page 70 ASSEMBLY INSTRUCTIONS HOSE A 2130-17/19 1/4 X 75 HOSE ASSEMBLY 2-1/2 X 1-1/2 2130-21 1/4 X 86 HOSE ASSEMBLY HYDRAULIC CYLINDER 2130-23 1/4 X 104 HOSE ASSEMBLY 2130-25 1/4 X 130 HOSE ASSEMBLY 45 ADAPTER HOSE ADAPTER 2130-17/19 1/4 X 80 HOSE ASSEMBLY 2130-21 1/4 X 90 HOSE ASSEMBLY 2130-23...
  • Page 71 ASSEMBLY INSTRUCTIONS (E-2) (E-1) (F-1) (F-2) FRONT OF FRONT OF FRONT OF MACHINE MACHINE MACHINE RIGHT MANIFOLD LEFT MANIFOLD CENTER MANIFOLD m175816 op p2 Figure 3-30: Chopper Reel Hydraulic Manifold Installation (Option) WING HOSE MOUNT TUBE HOSE MOUNT TUBE INSTALL HOSE MOUNTS AT ENDS SO U-BOLT CAN HELP PROTECT...
  • Page 72 ASSEMBLY INSTRUCTIONS ATTACH HOSE TO TOP OF FRAME USING HOSE CLAMPS (P/N’S 172977 AND 174784) ROUTE HOSES TO TRACTOR HOSE MOUNT TUBE WING HOSE MOUNT TUBE chopper reel hose routing2 Figure 3-32: Hose Mount Tube Installation 3-38 F-721-0513...

  • Page 73: Hydraulic Tubular Mount Chopper Reel Installation

    ASSEMBLY INSTRUCTIONS Hydraulic Tubular Mount Chopper Reel Installation HYDRAULIC TUBULAR MOUNT CHOPPER 1. Install hydraulic chopper reels in the same manner REEL ARM ASSEMBLY described for standard tubular mount chopper reels (See “Standard Tubular Mount Chopper Reel HOSES TO GO INSIDE Installation (Option)”...
  • Page 74 ASSEMBLY INSTRUCTIONS 3/4-10 X 3 HEX HEAD CAP SCREW 2 HOLE SUPPORT PLATE (INSIDE TUBE) COIL TINE HARROW ARM ASSEMBLY 3/4-10 HEX LOCK NUT 5/8-11 FLANGE HEAD SERRATED NUT 3/4-10 X 13 HEX HEAD HARROW STIFFENER CAP SCREW PLATE MOUNT PLATE ARM SUPPORT TUBE MOUNT PLATE 3/4-10 HEX LOCK NUT...

  • Page 75: Coil Tine Harrow Installation

    ASSEMBLY INSTRUCTIONS Coil Tine Harrow Installation See Figures 2-20 thru 2-22 for 3 Row Coil Tine Harrow placement dimensions. 1. Install 2 hole support plate into coil tine harrow arm assembly. Use (2) 3/4-10 x 3 hex head cap screws to hold plate in place.
  • Page 76 ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-42 F-721-0513...

  • Page 77: Operation And Maintenance

      DANGER DANGER Never allow anyone to ride on the 2131 wing Always lock the tractor drawbar in the center coulter chisel at any time. Allowing a person to position when transporting the unit. Failure to do ride on the machine can inflict serious personal so can result in serious injury or death and cause injury or death to that person.

  • Page 78: Tractor Preparation

    OPERATION AND MAINTENANCE Tractor Preparation Hydraulic Lift System The Landoll 2131 Wing Coulter Chisel is designed to be The Wing Coulter Chisel is equipped with a rephasing pulled by tractor equipped with a double lip or clevis type hydraulic lift system to raise and lower the unit in the field.
  • Page 79 OPERATION AND MAINTENANCE 1. The rephasing hydraulic lift system contains smaller wing frame cylinders plumbed in series with larger 2 X 16 TRANSPORT center frame cylinders. It is important that the LOCKOUT cylinders be connected in the proper series for the lift L PIN system to operate correctly.

  • Page 80: Hydraulic Fold System

    OPERATION AND MAINTENANCE Hydraulic Fold System  WARNING 1. The 2131 Wing Coulter Chisel is equipped with a Escaping hydraulic fluid can cause serious hydraulic fold system to raise and lower the wing personnel injury. relieve system pressure before frames for narrow transport.
  • Page 81 OPERATION AND MAINTENANCE 5. To fold/unfold the 2131 Wing Coulter Chisel, find a level area large enough to accommodate the WING STABILIZER implement when it is fully unfolded. The tractor BRACKET should be stopped and not moving with the unit fully raised.

  • Page 82: Hydraulic Coulter Gang Lift System

    OPERATION AND MAINTENANCE Hydraulic Coulter Gang Lift General Operation System 1. The horsepower requirements are typically 20-25 horsepower per shank. This will vary widely due to The rephasing coulter gang lift system must be purged of speed, depth, moisture, residue and types of soils. air before beginning field operation.

  • Page 83: Field Operation

    Leveling (Front-to-Rear) 1. Raise the unit to take the weight off of the transport 1. The leveling feature on the 2131 Wing Coulter Chisel locks. Remove the transport locks from the lift is used to keep the machine level when raising the cylinders (on the main frame only).

  • Page 84: Leveling (Side To Side)

    OPERATION AND MAINTENANCE Leveling (Side to Side) 1. Leveling the 2131 Wing Coulter Chisel side-to-side involves leveling the wing frame to the center frame. The unit should be level side-to-side when operating in the field. 2. To level the unit, verify that all tires are properly inflated.
  • Page 85 OPERATION AND MAINTENANCE 3. An adjusting wrench is provided to make this adjustment. It may be necessary to lower the wing to 4 X 16 HYDRAULIC BASE END the ground and relieve weight on the cylinder anchor CYLINDER ADJUSTMENT to make this adjustment. If required, fully raise the implement, lower to just above the ground, and re-verify measurements.

  • Page 86: Variable Ratio Adjustment

    OPERATION AND MAINTENANCE Variable Ratio Adjustment 1. To change the variable ratio adjustment, lower the implement to the ground and relieve the load on the The leveler is equipped with a variable ratio adjustment. lift system. This is located at the rear of the hitch and at the center of 2.

  • Page 87: Coulter Blades

    OPERATION AND MAINTENANCE Coulter Blades  DANGER 1. The 2131 Wing Coulter Chisel is equipped with 22" Coulter blades are extremely sharp. Exercise coulter blades. extreme care when working on or near coulter 2. The 22” diameter blades are flat with a thickness of 4 blades.

  • Page 88: Depth Stop Adjustment (Manual)

    OPERATION AND MAINTENANCE Depth Stop Adjustment (Manual) Wheel Bearing Maintenance The operating depth of the 2131 Wing Coulter Chisel is Wheel bearing maintenance should be performed at the controlled by a single-point depth stop. The stop is beginning of every season of use. Check the wheel located at the center front of the machine.

  • Page 89: Hydraulic Maintenance

    1. Check and follow all federal, state, and local requirements before transporting the Coulter Chisel. 2. The 2131 Wing Coulter Chisel should be transported only by tractor required for field operation. The implement weight should not exceed more than 1.5 times the tractor weight.
  • Page 90 OPERATION AND MAINTENANCE 4. Check that tires are of proper size, load rating, and inflated to manufacture specifications before 2 X 16 TRANSPORT transporting. Check wheel lug bolts to insure LOCKOUT tightness. L PIN 5. Know the transport heights and widths of the unit before transporting.
  • Page 91 OPERATION AND MAINTENANCE 2131 lube Figure 4-14: Lubrication Schedule LUBRICATION TABLE INTERVAL ITEM DESCRIPTION NO. OF LUBE POINTS (Hours Unless Stated) Disc Gang Bearings 1 each Radius Rod Walking Tandem Hubs 1 each Wheel Hubs 1 each Table 4-1: Lubrication Table...

  • Page 92: Lubrication Maintenance

    Lubrication Maintenance Storage 1. Table 4-1 specifies the lubrication points and 1. The service life of the 2131 Wing Coulter Chisel will intervals on the 2131 Wing Coulter Chisel. Proper be extended by proper off-season storage practices. maintenance of your machine will, under normal...

  • Page 93: Troubleshooting Guide

    Chapter 5 Troubleshooting Guide PROBLEM PROBABLE CAUSE SOLUTION UNIT NOT PULLING EVEN Coulter gangs uneven depth Adjust depth/rephase coulter gang cylinders (See “Hydraulic Coulter Gang Lift System” on page 4-6.) UNEVEN DEPTH Unit not level when under power in the field Level unit front to rear (See “Leveling (Front-to-Rear)”...
  • Page 94 TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE SOLUTION HYDRAULIC - COULTER LIFT Lift cylinders not in phase Fully extend cylinders and hold hydraulic CYLINDERS NOT FULLY EXTENDING lever until all cylinders are fully extended. Cylinders not installed in proper series Wing cylinders are smaller diameter than center cylinders.
  • Page 96 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Model 2131 Wing Coulter Chisel Operator’s Manual Re-Order Part Number F-721-0513 LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...

Table of Contents