Related Manuals for Landoll 2510 Series
Summary of Contents for Landoll 2510 Series
- Page 1 2510 Series In-Row Ripper Operator’s Manual LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-729-0913 09/2013...
-
Page 3: Table Of Contents
Table of Contents Introduction Understanding Safety Statements ..........1-2 Standard Specifications Assembly Instructions Assembly Preparation . - Page 4 F-729-0913 Edition...
-
Page 5: Introduction
Chapter 1 Introduction The Landoll Model 2510 In-Row Ripper is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation CHAPTER 1 gives basic instructions on the use of this manual. -
Page 6: Understanding Safety Statements
INTRODUCTION Understanding Safety Statements You will find various types of safety information on the following pages and on the machine signs (decals) attached to the vehicle. This section explains their meaning. The Safety Alert Symbol means ATTENTION! YOUR SAFETY IS INVOLVED! ... -
Page 7: Standard Specifications
Chapter 2 Standard Specifications 2510 SERIES IN-ROW RIPPER SPECIFICATIONS ESTIMATED MODEL NO. OF SHANK TRANSPORT WEIGHT SHANKS SPACING SHANK EXTENSIONS WIDTH (LBS.) 2510-4-30 30” NONE 11’-2” 3,205 2510-5-30 30” NONE 11’-2” 3,812 2510-6-30 30” 17” BOLT-ON 14’-2” 4,610 2510-7-30 30”... - Page 8 STANDARD SPECIFICATIONS F-729-0913 Edition...
- Page 9 STANDARD SPECIFICATIONS LANDOLL CORPORATION GENERAL TORQUE SPECIFICATIONS (REV. 4/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR GENERAL PURPOSE APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED NUTS AND CAPSCREWS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION). THEY DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED.
- Page 10 STANDARD SPECIFICATIONS LANDOLL CORPORATION HYDRAULIC FITTING TORQUE SPECIFICATIONS JIC, ORS, & ORB (REV. 10/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR HYDRAULIC FITTING APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED CARBON STEEL AND STAINLESS STEEL FITTINGS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION) THEY DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED.
- Page 11 STANDARD SPECIFICATIONS 2510-5 shank and lighting placement Figure 2-1: 2510-5-30 Shank and Lighting Placement...
- Page 12 STANDARD SPECIFICATIONS 29-1/2 2510-6 shank and lighting placement Figure 2-2: 2510-6-30 Shank and Lighting Placement F-729-0913 Edition...
- Page 13 STANDARD SPECIFICATIONS 82-7/16 2510-7 shank and lighting placement Figure 2-3: 2510-7-30 Shank and Lighting Placement...
- Page 14 STANDARD SPECIFICATIONS Page Intentionally Blank F-729-0913 Edition...
-
Page 15: Assembly Instructions
Chapter 3 Assembly Instructions It is very important that your new 2510 Series In-Row IMPORTANT Ripper be properly assembled, adjusted, and lubricated before use. Illustrations are provided in this section to Check all bolt lengths, nut sizes, etc., from the parts show proper assembly procedures. - Page 16 ASSEMBLY INSTRUCTIONS SMV EMBLEM SMV MOUNTING BRACKET U-BOLT 5/8-11 HEX LOCK NUT RIGID GAUGE WHEEL ADJUSTMENT PIN 3/16 HAIR PIN OUTER JACK STAND TUBE JACK STAND m2510-parts-id Figure 3-1: 2510 Series Parts Identification F-729-0913 Edition...
-
Page 17: Assembly Preparation
ASSEMBLY INSTRUCTIONS Assembly Preparation SMV Bracket Installation 1. Hook up the In-Row Ripper to a tractor using the 1. Attach the SMV mounting bracket to the center of the three-point hitch. Raise the unit about 36” and place rear frame using u-bolt and 5/8-11 flange head stands under the main frame to prevent accidental serrated nuts (See Figure 3-1.) lowering. -
Page 18: Auto-Reset Clamp And Shank Assembly
ASSEMBLY INSTRUCTIONS 5/8-11 X 3-3/4 HEX HEAD CAP SCREW 3/4-10 X 4 HEX HEAD CAP SCREW SPRING CLAMP ASSEMBLY POINT PIN PLACEMENT CONNEX BUSHING 3/4-10 X 4 HEX HEAD 3/4-10 HEX CAP SCREW LOCK NUT 5/8-11 HEX LOCK NUT WEARSTRIP BRACKET 3/4-10 X HEX WEARSTRIP... -
Page 19: Rsb Clamp And Straight Shank Assembly
ASSEMBLY INSTRUCTIONS 5/8-11 X 5-1/2 HEX HEAD CAP SCREW 3/4-10 X 4 HEX HEAD CAP SCREW RIGID CLAMP ASSEMBLY POINT PIN PLACEMENT CONNEX BUSHING 3/4-10 X 4 HEX HEAD 3/4-10 HEX CAP SCREW LOCK NUT 5/8-11 HEX LOCK NUT 3/4-10 X HEX WEARSTRIP LOCK NUT BRACKET... - Page 20 ASSEMBLY INSTRUCTIONS FRAME SHANK 3/8 X 2 SPRING SLOTTED PIN CLAMP 1/2-13 X 6 HEX HEAD CAP SCREW 5/8-11 X 1-1/2 SET SCREW 1/2 SPLIT LOCK 1/2-13 HEX NUT WASHER CLAMP PLATE COULTER ASSEMBLY 1/2-13 X 1-1/2 ROUND HEAD SQUARE NECK SCREW 1/2 SPLIT LOCK WASHER...
-
Page 21: Coulter Assembly
ASSEMBLY INSTRUCTIONS Coulter Assembly 1. Assemble coulter shank to coulter assembly using coulter stop weldment and 5/8-11 x 1-1/2 square head set screw. Install 3/8 x 2 spring slotted pins in coulter shank. 2. Install the shank and coulter assembly to the frame with the coulter clamps and plates using 1/2-13 x 6 hex head cap screws and hex lock washers (See Figure 3-4.) - Page 22 ASSEMBLY INSTRUCTIONS 19” SELF LOCKING TIE RIGHT LIGHT BRACKET 1/4-20 HEX LOCK NUT W/ REFLECTORS HARNESS STOR-AWAY TAIL LIGHT MOUNT 1/4-20 X 3/4 HEX REFLECTOR ASSEMBLY HEAD CAP SCREW AG AMBER SINGLE STOR-AWAY HOLDER LED LAMP BRACKET 5/8-11 FLANGE HEAD SERRATED NUT 7 PIN/4 PIN HARNESS, 1/4-20 X 1-1/2 HEX...
-
Page 23: Electrical Installation
ASSEMBLY INSTRUCTIONS 7-PIN 4-PIN CIRCUIT WIRE CONN TOWER COLOR 2-PIN 3-PIN 6-PIN 3-PIN 2-PIN TOWER TOWER SHROUD TOWER TOWER GROUND GROUND BLACK WORK LAMPS BLACK LEFT TURN LEFT FLASHING YELLOW WHITE & TURN GROUND STOP LAMPS BROWN RIGHT FLASHING GREEN TAIL &... - Page 24 ASSEMBLY INSTRUCTIONS Notes: 3-10 F-729-0913 Edition...
-
Page 25: Operation And Maintenance
Chapter 4 Operation and Maintenance DANGER WARNING Coulter blades are sharp. Do not allow coulters to All hydraulically elevated equipment must be roll over or fall on any part of the body. Do not locked out or lowered to the ground when allow wrenches to slip when working near coulter servicing or when equipment is idle, to prevent blades. -
Page 26: Tractor Preparation
CAT III HITCH m2510-hitch Figure 4-1: 3 Point Hitch Setup Tractor Preparation The 2510 Series In-Row Ripper may be used on tractors equipped with category II or III three-point hitches. Before attaching the In-Row Ripper, prepare the tractor as follows: The rear tractor tires should be inflated equally and ballast added according to the tractor operator’s manual. -
Page 27: In-Row Ripper Operation
OPERATION AND MAINTENANCE In-Row Ripper Operation Field Operation — Three-Point Hitch Type 1. Before operating the In-Row Ripper, inspect it to be sure it is in good operating condition. 1. Lower the In-Row Ripper to the ground and pull it a 2. -
Page 28: Wheel Bearing Maintenance
OPERATION AND MAINTENANCE Wheel Bearing Maintenance Lubrication 1. Check wheel bearings and coulter bearings IMPORTANT occasionally for excessive end play. To correctly replace the wheel bearings: Items with grease zerks are listed in the illustrated parts book. 2. Place the frame on blocks or stands sufficient to lift the tire clear of the ground. - Page 29 OPERATION AND MAINTENANCE Notes...
- Page 30 OPERATION AND MAINTENANCE F-729-0913 Edition...
-
Page 31: Troubleshooting Guide
Troubleshooting Guide The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 2510 Series In-Row Ripper. Follow all safety precautions stated in the previous sections when making any adjustments to your machine. - Page 32 TROUBLESHOOTING GUIDE Notes F-729-0913 Edition...
- Page 34 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001:2008 registration at all Landoll manufacturing facilities. Model 2510 Series In-Row Ripper Operator’s Manual Re-Order Part Number F-729-0913 LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...