Related Manuals for Landoll 2220 Series
Summary of Contents for Landoll 2220 Series
- Page 1 MODEL 2220 SERIES DISC CHISEL OPERATOR’S MANUAL 1900 NORTH STREET MA RYS VILLE, KAN SAS 66508 (785) 562- 5381 F-312-0605 06/05...
- Page 2 WARRANTY MANU FAC TUR ER’S GUAR AN TEE POL ICY LAN DOLL COR PO RA TION WAR RANTY LAN DOLL war rants each new and un used LAN DOLL ma chine, when prop erly as sem bled, ad justed, and op er ated, to be free of de fects in ma te rial and work man ship, in nor mal use and when prop erly serv iced, for a pe riod of twelve (12) months af ter date of de liv ery by the Dealer to the origi nal re tail pur chaser.
- Page 3 MODEL 2220 SE RIES DISC CHISEL OP ERA TOR’S MAN UAL PUR CHASED FROM: DATE AD DRESS: PHONE NO.: SE RIAL NO.:...
-
Page 5: Table Of Contents
TA BLE OF CON TENTS SEC TION DE SCRIP TION PAGE NO. IN TRO DUC TION ........1-1 STAN DARD SPEC I FI CA TIONS . - Page 6 SAFETY PRECAUTIONS THIS IS THE SAFETY ALERT SYM BOL. IT IS USED TO ALERT YOU TO PO TEN TIAL IN JURY HAZ ARDS. OBEY ALL SAFETY MES SAGES THAT FOL LOW THIS SYM BOL TO AVOID POS SI BLE IN JURY OR DEATH.
-
Page 7: Introduction
INTRODUCTION The Lan doll 2220 Se ries Disc Chisel is a qual ity prod uct de signed to give years of trou ble free per form - ance. By fol low ing each sec tion of this man ual, your sys tem will per form as de signed for you and your op - era tion. -
Page 9: Standard Specifications
STANDARD SPECIFICATIONS MODEL WORKING TRANSPORT NO. OF NO. OF WEIGHT NUMBER WIDTH WIDTH SHANKS DISCS (APPROX.) (ft.-in.) (lbs.) 11’-7” 12’-5" 7,520 2225- 7R-15 11’-7” 12’-5” 7,590 2225-7A-15 14’-9” 15’-7” 8,120 2225-9R-15 14’-9” 15’-7” 8,210 2225-9A-15 16’-5” 17’-3” 8,600 2225-11R-15 16’-5” 17’-3"... - Page 10 LANDOLL CORPORATION GENERAL TORQUE SPECIFICATIONS (REV. 4/97) THIS CHART PRO VIDES TIGHT EN ING TORQUES FOR GEN ERAL PUR POSE AP PLI CA TIONS WHEN SPE CIAL TORQUES ARE NOT SPECI FIED ON PROC ESS OR DRAW ING. AS SEM BLY TORQUES AP PLY TO PLATED NUTS AND CAP SCREWS AS SEM BLED WITH OUT SUP PLE MEN TAL LU BRI CA TION (AS RE CEIVED CON DI TION).
- Page 11 LANDOLL CORPORATION HYDRAULIC FITTING TORQUE SPECIFICATIONS JIC, ORS, & ORB (REV. 10/97) THIS CHART PRO VIDES TIGHT EN ING TORQUES FOR HY DRAU LIC FIT TING AP PLI CA TIONS WHEN SPE CIAL TORQUES ARE NOT SPEC I FIED ON PRO CESS OR DRAW ING.
- Page 12 NOTES:...
- Page 13 Fig ure 2-1 - 2225- 7A- 15DC Shank Spac ing...
- Page 14 Fig ure 2-2 - 2225- 9A- 15DC Shank Spac ing...
- Page 15 Fig ure 2-3 - 2225- 11A- 15DC Shank Spac ing...
- Page 16 Fig ure 2-4 - 2227- 11A- 15DC Shank Spac ing...
- Page 17 Fig ure 2-5 - 2227- 13A- 15DC Shank Spac ing...
- Page 18 Fig ure 2-6 - 2227- 15A- 15DC Shank Spac ing 2-10...
-
Page 19: Assembly Instructions
ASSEMBLY INSTRUCTIONS WARN ING It is very im por tant that your new 2220 Se ries Disc Chisel be prop erly as sem bled, ad justed and DO NOT AT TEMPT TO LIFT HEAVY lu bri cated be fore use. Il lus tra tions to as sist with the as sem bly pro cess are pro vided in Sec tion 2, PARTS (SUCH AS THE FRAME, DISC “Stan dard Speci fi ca tions”. - Page 20 Fig ure 3-1 2227 Frame As sem bly...
-
Page 21: 2225 Frame As Sem Bly
3-1 2225 FRAME AS SEM BLY No as sem bly is needed for the 2225 frame. How ever, it needs to be placed on stands about 36" high in an open, level area. If your Disc Chisel is equipped with frame ex ten sions, see Sec tion 3-2.4 and 3-2.5 for their proper in stal la tion pro ce - dures. - Page 22 Fig ure 3-2 2225 Rock shaft In stal la tion Fig ure 3-3 2225 Gauge Wheel Cyl in der In stal la tion...
-
Page 23: 2225 Rockshaft In Stal La Tion
3-3 2225 ROCK SHAFT IN STAL LA TION IMPORTANT 3-3.5 In sert the rock shaft shims, as needed, be tween each set of bear ings. Use the shims READ ALL SAFETY PRE CAU TIONS AT THE to al low the rock shaft to ro tate freely, yet not FRONT OF THIS SEC TION BE FORE AT TEMPT - loosely, in the bear ing halves. - Page 24 Fig ure 3-4 2227 Rock shaft In stal la tion Fig ure 3-5 2227 Gauge Wheel Cyl in der In stal la tion...
-
Page 25: 2227 Rockshaft In Stal La Tion
3-4 2227 ROCK SHAFT IN STAL LA TION IMPORTANT 3-4.5 In sert the rock shaft shims, as needed, be tween each set of bear ings. Use the shims READ ALL SAFETY PRE CAU TIONS AT THE to al low the rock shaft to ro tate freely, yet not FRONT OF THIS SEC TION BE FORE AT TEMPT - loosely, in the bear ing halves. - Page 26 Fig ure 3-6 2225 Hy drau lic Hose In stal la tion 2225 HYDRAULIC HOSE HOSE PART NUMBER DESCRIPTION 1- 397- 010300- 09 HOSE 234" 1- 397- 010104 HOSE 50" 1- 397- 010081 HOSE 60" 1- 397- 010299- 10 HOSE 41" 1- 397- 010299- 01 HOSE 36"...
-
Page 27: 2225 Hy Drau Lic Plumb Ing In Stal La Tion
3-5 2225 HY DRAU LIC PLUMB ING IN STAL LA TION 3-5.3 In stall a 90° re stric tor fit ting to the base IM POR TANT end ports of both gauge wheel cyl in ders. 3-5.4 In stall a 90° un re stricted fit ting to the 1. - Page 28 Fig ure 3-7 2227 Hy drau lic Hose In stal la tion 2227 HYDRAULIC HOSE HOSE PART NUMBER DESCRIPTION 1- 397- 010300- 02 HOSE 300" 1- 397- 010299- 13 HOSE 74" 1- 397- 010299- 02 HOSE 60" 1- 397- 010071 HOSE 94"...
-
Page 29: 2227 Hy Drau Lic Plumb Ing In Stal La Tion
3-6 2227 HY DRAU LIC PLUMB ING IN STAL LA TION IM POR TANT 3-6.7 In stall a No. 2 hose to the rod port of the right- hand gauge wheel cyl in der and to 1. Pipe seal ant is not re quired to in stall hoses the lower port on the right side of the hy - to mani fold and cyl in ders equipped with hy - drau lic mani fold. - Page 30 Fig ure 3-8 Pull Hitch In stal la tion 3-12...
-
Page 31: Pull Hitch In Stal La Tion
3-7 PULL HITCH IN STAL LA TION IMPORTANT 3-7.3 (2227 Only) In stall the front lev eler link be tween the mast plates: READ ALL SAFETY PRE CAU TIONS AT THE FRONT OF THIS SEC TION BE FORE AT TEMPT - IMPORTANT ING ANY OF THE FOL LOW ING PRO CE DURES. - Page 32 Fig ure 3-9 Disc Gang In stal la tion 3-14...
-
Page 33: Disc Gang In Stal La Tion
3-8 DISC GANG IN STAL LA TION IMPORTANT 3-8.1 FRONT DISC GANG IN STAL LA TION. READ ALL SAFETY PRE CAU TIONS AT THE IMPORTANT FRONT OF THIS SEC TION BE FORE AT TEMPT - THE FRONT DISC GANG FRAMES ARE THE ING ANY OF THE FOL LOW ING PRO CE DURES. - Page 34 Fig ure 3-11 Disc Gang Hy drau lic In stal la tion 3-16...
-
Page 35: Disc Gang Hy Drau Lic Ad Just Ment/In Stal La Tion
e. In stall a bush ing in the outer frame bracket f. Two an gle ad just pins are in stalled in the by put ting a 1" x 6" bolt up through the outer mount ing bracket with hair pins. Make bracket and a nut on the top. - Page 36 3-9.5 2225 Ra dius Rod In stal la tion Only — b. In stall one end of the short ra dius rod to the For ma chines with even num ber of shanks in side of the disc ad just frame us ing the same (See Fig ure 3-11).
-
Page 37: Spring Cush Ion Clamp In Stal La Tion
3-10 SPRING CUSH ION CLAMP IN STAL LA TION IMPORTANT b. If us ing twisted shov els, in stall all shanks so shov els throw soil in ward ex cept shov els near READ ALL SAFETY PRE CAU TIONS AT THE wheels. -
Page 38: Cals
3-11 DE CALS De cals are pro vided for your safety and for 3-11.2 Am ber de cals must go on the left disc ma chine iden ti fi ca tion. Be sure to keep safety de - gang frames fac ing on- coming traf fic. cals legi ble and clean. -
Page 39: Warn Ing Lights In Stal La Tion
Fig ure 3-15 Wir ing Dia gram 3-12 WARN ING LIGHTS IN STAL LA TION IMPORTANT 3-12.1 As sem ble lights to the light bracket us - ing 1/4 X 1-3/4 cap screws and nuts. In sure MAKE SURE LIGHTS ARE PO SI TIONED FOR the wires are in the groove in the base of the MAXI MUM VISI BIL ITY FROM THE REAR. - Page 40 NOTES: 3-22...
-
Page 41: Operation And Maintenance
OPERATION AND MAINTENANCE DAN GER DAN GER NEVER AL LOW ANY ONE TO RIDE ON WHEN TRANS PORT ING THE UNIT, THE 2220 SE RIES DISC CHISEL AT PLACE CYL IN DER LOCK OUTS ANY TIME. AL LOW ING A PER SON TO THE TRANS PORT LOCK PO SI TION RIDE ON THE MA CHINE CAN IN FLICT AF TER FULLY EX TEND ING THE CYL -... -
Page 42: Trac Tor Prepa Ra Tion
TRAC TOR PREPA RA TION The Lan doll 2220 Se ries Disc Chisel is de - 4-1.1 In flate the rear trac tor tires equally and signed to be pulled by trac tor equipped with a dou - add bal last ac cord ing to the trac tor op era - ble lip or cle vis type hitch. -
Page 43: Field Op Era Tion
4-4 FIELD OP ERA TION 4-4.1 Re move the trans port lock pins from the 4-4.7 Disc Gang Op era tion. The disc gangs cyl in der lock outs. Use them to hook the lock - may be set at an an gle of 10, 15, or 20 De - outs to the lock out an chor chains. -
Page 44: Wheel Bear Ing Main Te Nance
4-5 WHEEL BEAR ING MAIN TE NANCE 4-5.4 Re pack the bear ings us ing a high- Wheel bear ing main te nance should be per - quality wheel bear ing grease. formed at the be gin ning of every sea son of use. 4-5.5 Re place the hub with a new seal and Check the wheel bear ings pe ri odi cally for ex ces -... - Page 45 Fig ure 4-4 Lu bri ca tion Sched ule...
- Page 46 NOTES...
-
Page 47: Troubleshooting Guide
TROUBLESHOOTING GUIDE The Trou ble shoot ing Guide, shown be low, is in cluded to help you quickly lo cate prob lems that can hap - pen us ing your 2220 Se ries Disc Chisel. Fol low all safety pre cau tions stated in the pre vi ous when mak ing any ad just ments to your ma chine. - Page 48 PROBLEM PROBABLE CAUSE:SOLUTION 5. SHANKS PLUG A. FRONT DISCS SET TOO SHAL LOW: Lower disc gangs to get bet ter cut ting ac tion, 5" to 6" deep. B. SHANKS NOT SPACED COR RECTLY: See shank place ment Fig ures 2-1 to 2-6. Ad just if nec es sary. 6.
- Page 50 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Model 2220 Series Disc Chisel Operator’s Manual Re-Order Part Number F-312-0605 LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...