Table of Contents
Advertisement
Menu Item
CUSTOM GAMMMA MODE
―
EASY MODE
― DEFAULT RESET
― SELECT
― CURVE TYPE
― INITIAL GAIN
― 18% GRAY
― DYNAMIC RANGE
― WHITE LIMIT
― CAL
SAVE
― FLEXIBLE MODE
― DEFAULT RESET
― SELECT
― POINT
― WIDTH
― LEVEL
CAL
― SHUTTER
― SHUTTER SPEED
― GAMMA CURVE COPY
― SD MEMORY CARD
― SAVE
LOAD
PRESET FILE LOAD
ENGINEER
― FILE SELECT
LOAD START
*2 : CUSTOM GAMMA MODE - Loads the custom gamma data from SD card through the LOAD menu.
Initial
Setting Value
Setting
---
EXECUTE, CANCEL
NORMAL, CINE1-2,
NORMAL
CUSTOM1-5
NORMAL, LOG,
---
SPECIAL
---
1.0 - 9.0
---
14.0% - 107.0%
---
100% - 600%
---
70% - 109%
OFF, CAL100%,
OFF
CAL200%, CAL300%,
CAL400%, CAL600%
EXECUTE,
---
CANCEL
READY
CANCEL, EXECUTE
NORMAL
NORMAL,CUSTOM1 to 5 Selects the gamma table to be created.
100%
15 to 440%
60%
20 to 100%
0
-100 to 100
OFF, CAL100%,CAL200
OFF
%,CAL300%,CAL400%,C
AL600%
OFF, PRESET,
OFF
VARIABLE
PRESET:
1/100 - 1/2000
1/100
VARIABLE:
1/63.4 - 1/1983
CUSTOM1-5 -->
---
CUSTOM1-5
---
---
---
---
ENGINEER, FACTORY
READY, START,
READY
CANCEL
HDK-65C 1501 VER1 (U)
5.2 Settings from the Menu
Description, Remarks
Easy creation mode. Sets various parameters and creates the
custom gamma data.
Returns to the original custom gamma data.
If you have saved the custom gamma data with the "SAVE"
function, it returns to the saved data.
The original data cannot be recovered once it is overwritten
with the "SAVE" function.
Selects the gamma table to be created.
Sets the basic properties of gamma curve.
Sets the slope of gamma curve at around 0%.
The curve rises steeply as the value increases.
Sets what level it should be after the gamma has been
applied when converting from 18% level before applied.
Sets the maximum level (the maximum input level to the
gamma) before the gamma has been applied.
Sets the white clip after the gamma has been applied.
Selects the test waveform (CAL) to check the gamma table.
Saves the data that has been created.
The data is temporary unless you save it.
Therefore, the data will be cleared if you end the menu
without saving it.
Flexible creation mode. Edits the already created custom
gamma data.
Returns to the original custom gamma data.
Sets the video level before the gamma has been applied.
Sets the width of the video level .
Sets the video level of the range set by the WIDTH and POINT.
Sets the test waveform to verify gamma table.
Selects for the electronic shutter.
Switches the shutter speed.
(When SHUTTER is in PRESET and VARIABLE only.)
Copies the gamma data that has been created into the other
data in the camera.
Saves the custom gamma data in an SD card.
Loads the custom gamma data from an SD card.
Function to load the user settings (ENGINEER SET FILE)
or factory settings (FACTORY SET FILE) for the level
adjustment or menu of the camera.
Used to return the camera state back to the previous or
initial settings.
ENGINEER : Initializes the state back to the user setting.
FACTORY
: Initializes the state back to the initial factory
setting.
Executes initialization.
MENU DATA
ALL
VF
-
-
-
-
-
-
*2
-
-
*2
-
*2
-
-
*2
-
-
*2
-
-
-
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
91
Advertisement
Table of Contents
