Ikegami HDK-65C Operation Manual page 109

3
On MENU (3/4), turn the rotary pulse switch to
position the cursor on "LENS SELECT", and press
the SET button.
The submenu is displayed.
4
Set "NUMBER", "NAME" and "EXTENDER".
Refer to the explanation of corresponding item for how
to set each data.
NO. 1 is selected here as an example.
CAUTION:
If a new file is created with the same file number as an existing file, the data will be overwritten and the old data will be lost.
5
Turn the rotary pulse switch to position the cursor
on "FILE SET", and press the SET button.
The cursor moves to the mode selection column.
6
Turn the rotary pulse switch to select the set value,
and press the SET button.
The value is confirmed, and either of the following
messages is displayed at the bottom of the screen:
- LENS No. x
- PUSH SET -> START : Displayed and flashes when
Go to Step 7 when "AUTO" is selected.
When "MANUAL" is selected, go to Step M1 to obtain
the model name of the lens after lens file items such as
GAIN/FLARE/GAMMA are adjusted by MCP, etc.
7
Press the SET button.
The lens file is created.
8
Set the S11-4 DIP switch of the MPU module back to "OFF".
Note:
- When the camera is powered OFF, the FILE SET settings are turned OFF.
- Before creating lens files, prepare all the lenses to use. Then, create the files under the same condition at a time. If the conditions are
changed, the setting cannot be accurate. Lens files memorize a difference in level between lenses. If the lighting or chart is changed,
it cannot tell whether it is the lighting error, chart error, or lens error.
: Displayed when "MANUAL"
is selected.
"AUTO" is selected.
HDK-65C 1501 VER1 (U)
5.2 Settings from the Menu
＊＊＊ ＭＥＮＵ （３／３） ＊＊＊
▲
ＳＣＡＮ ＦＯＲＭＡＴ ＳＥＬＥＣＴ
ＣＰＵ ＳＹＳＴＥＭ ＣＯＮＴＲＯＬ
ＡＵＴＯ ＩＲＩＳ ＳＥＴ
ＡＵＴＯ ＳＥＴＵＰ ＭＯＤＥ
ＬＥＮＳ ＳＥＬＥＣＴ
ＬＥＶＥＬ ＡＤＪＵＳＴ
ＰＲＯＣＥＳＳ ＭＯＤＥ
ＣＵＳＴＯＭ ＧＡＭＭＡ ＤＡＴＡ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＬＥＮＳ ＳＥＬＥＣＴ
ＮＵＭＢＥＲ ＮＯ．１
ＮＡＭＥ （ ）
（ＡＢ４０Ｘ１０ ＡＢＣＤ ）
ＥＸＴＥＮＤＥＲ ＯＦＦ
ＡＵＴＯ ＳＥＬ ＯＦＦ
ＦＩＬＥ ＳＥＴ ＯＦＦ
ＬＥＮＳ ＴＹＰＥ ＊＊＊
ＡＵＴＯ Ｘ０．８ ＣＯＮＶ ＯＦＦ
ＬＥＮＳ ＳＥＲＩＡＬ Ｉ／Ｆ ＯＦＦ
ＦＩＬＥ ＳＥＴ ＯＦＦ
ＬＥＮＳ ＮＯ．１
ＰＵＳＨ ＳＥＴ→ＳＴＡＲＴ
③
Position the flashing
cursor on "LENS
SELECT" and confirm.
⑤
Position the cursor on
5
"FILE SET" and
confirm.
⑥
Select the set value
and confirm.
⑦
Either message is
displayed or flashes.
93