Ikegami HDK-65C Operation Manual page 111

Note:
- When the new model name cannot be loaded from
the lens, "READ ERROR" appears on the bottom
instead of "COMPLETED".
- When the rotary pulse switch is turned to switch the
cursor on "CANCEL" to "CLR" and the SET button
is pressed in Step M2, "COMPLETED" appears on
the bottom.
Next, when "COMPLETED" disappears, the area to
display a model name automatically obtained from
the lens will be blank.
Note:
The lens name used for "AUTO SEL" can be edited so that the lens file can be shared with a similar lens.
The following explains the procedures.
E1
Follow Steps 1 to 3 of lens file creation to display the submenu.
E2
Turn the rotary pulse switch to position the cursor
on "NUMBER", and press the SET button.
The registered lens numbers (NO. 1 to NO. 8) are
displayed.
E3
Turn the rotary pulse switch to position the cursor
on the lens number of the file name to be edited,
and press the SET button.
The NO.5 lens set in "AUTO SEL" is selected here as
an example and the AUTO SEL NAME display part
displays "AB40X10 ABCD".
ＮＵＭＢＥＲ ＯＦＦ
ＮＡＭＥ （ ）
ＭＯＤＥＬ ＡＵＴＯ ＲＥＡＤ
ＥＸＴＥＮＤＥＲ ＯＦＦ
ＡＵＴＯ ＳＥＬ ＯＦＦ
ＦＩＬＥ ＳＥＴ ＭＡＮＵＡＬ
ＬＥＮＳ ＴＹＰＥ ＊＊＊
ＬＥＮＳ ＮＯ．１
ＲＥＡＤ ＥＲＲＯＲ
ＮＵＭＢＥＲ ＯＦＦ
ＮＡＭＥ （ ）
ＭＯＤＥＬ ＣＬＲ
ＥＸＴＥＮＤＥＲ ＯＦＦ
ＡＵＴＯ ＳＥＬ ＯＦＦ
ＦＩＬＥ ＳＥＴ ＭＡＮＵＡＬ
ＮＵＭＢＥＲ ＮＯ．１
ＮＡＭＥ （ ）
ＭＯＤＥＬ ＡＵＴＯ ＲＥＡＤ
ＥＸＴＥＮＤＥＲ ＯＦＦ
ＡＵＴＯ ＳＥＬ ＯＦＦ
ＦＩＬＥ ＳＥＴ ＭＡＮＵＡＬ
ＬＥＮＳ ＴＹＰＥ ＊＊＊
ＬＥＮＳ ＮＯ．１
ＣＯＭＰＬＥＴＥＤ
ＮＵＭＢＥＲ ＯＦＦ
ＮＡＭＥ （ ）
（ ）
ＥＸＴＥＮＤＥＲ ＯＦＦ
ＡＵＴＯ ＳＥＬ ＯＦＦ
ＦＩＬＥ ＳＥＴ ＭＡＮＵＡＬ
ＬＥＮＳ ＴＹＰＥ ＊＊＊
ＬＥＮＳ ＮＯ．１
ＬＥＮＳ ＳＥＬＥＣＴ
ＮＵＭＢＥＲ
ＮＡＭＥ （ ）
（ ）
ＥＸＴＥＮＤＥＲ
ＡＵＴＯ ＳＥＬ
ＦＩＬＥ ＳＥＴ
ＬＥＮＳ ＴＹＰＥ
ＡＵＴＯ Ｘ０．８ ＣＯＮＶ
ＬＥＮＳ ＳＥＲＩＡＬ Ｉ／Ｆ
ＬＥＮＳ ＳＥＬＥＣＴ
ＮＵＭＢＥＲ
ＮＡＭＥ （ ）
（ＡＢ４０Ｘ１０ ＡＢＣＤ ）
ＥＸＴＥＮＤＥＲ
ＡＵＴＯ ＳＥＬ
ＦＩＬＥ ＳＥＴ
HDK-65C 1501 VER1 (U)
5.2 Settings from the Menu
When the new model
name cannot be
loaded
Switch the cursor to
"CLR" and confirm.
"COMPLETED"
appears.
The area will be blank.
E②
ＯＦＦ
Position the cursor on
"NUMBER" and confirm.
ＯＦＦ
ＯＦＦ
ＯＦＦ
＊＊＊
ＯＦＦ
ＯＦＦ
E③
ＮＯ．５
Select the target lens
number and confirm.
ＯＦＦ
ＯＦＦ
ＯＦＦ
5
95