5Way(5Way); Analog; Gyro - Ko Propo EX-NEXT Instruction Manual

3-8CH
5WAY
Modify the 5-interval output settings.
Example
May be used for gear changing operations or when you wish to
set a 5-interval control scheme for the servo.
3CH MODE : 5WAY
START : POS1
KEY : ET3
NOW : 0
+
Setting Range
START : POS1,POS2,POS3,POS4,POS5 (Default : POS3)
Sets the starting position.
KEY : OFF, ET1 - 5(Default : OFF)
Assigns a key to use for switching positions.
POS 1 : -100 - 100(Default : -100)
Sets Position 1's output position.
POS 2 : -100 - 100(Default : -50)
Sets Position 2's output position.
POS 3 : -100 - 100(Default : 0)
Sets Position 3's output position.
POS 4 : -100 - 100(Default : 50)
Sets Position 4's output position.
POS 5 : -100 - 100(Default : 100)
Sets Position 5's output position.
P
The current output position is displayed by "NOW"
and shown on the bar graph.

ANALOG

These settings are to enable continuous output for each
channnels.
3CH MODE : ANALOG
KEY : ET3
REVERSE : NORM
STEP : 5
NOW : 0
+
P
The current output position is displayed by "NOW"
and shown on the bar graph.
Setting Range
KEY: OFF,ET1 - 5(Default : OFF)
Assigns a key to use for switching positions.
REVERSE : NOR , REV
(normal)
Sets operation direction.
STEP : 1 - 25(Default : 5)
Sets the amount of change for the operation.
3-8CH
POS1 : -100
POS2 : - 50
POS3 : 0
POS4 : 50
POS5 : 100
ー
3-8CH
LOW : -100
CEN : 0
HIGH : 100
ー
(Default : NORM)
(reverse)
LOW -100 - 0 (Default : -100)
(low position)
Sets the lowest value for the operation range.
CEN LOW - HIGH (Default : 0)
(center position)
Sets the neutral position for the operation range.
HIGH 0 -100 (Default : 100)
(high position)
Sets the highest value for the operation range.
How to Use Analog Settings
Low Position Side :
Between LOW and CEN are 100 steps within which the intervals can be
adjusted.
High Position Side :
Between CEN and HIGH are 100 steps within which the intervals can be
adjusted.
Example) When STEP value is 2
When LOW side is set to 5 intervals.
When HIGH side is set to 4 intervals.
High position
2 steps
100 steps
HIGH Maximum
P
Center position is the staring position.
Low/High positions cannot be exceeded. Operations
P
which try to do so will stop just before the Low/High
positions.

GYRO

This function modifies the setting for gyro control.
Example
Used when you want to use a Gyro system which the gain is
controlled by 3CH or 4CH.
Setting range
This is as same as Analog function.
How to set Gyro mode
The setting is forcibly as follows by Gyro mode.
KG-X
Using 3ch or 4ch.
KR-212FHG
ET3 : 3ch control (Steering gyro gain control)
ET5 : 4ch control (Throttle gyro gain control)
Adjust it to moderate gyro gain while running.
If set Gyro mode in the 3ch or 4ch, both channel will be set to the
Gyro mode.
When the 3ch/4ch mode is changed from GYRO mode to another
mode or OFF, the ET3 and ET5 will return to the setting for (OFF).
Please notice ET3 are not return to the default value(T: BRAKE).
Please prepare the gyro system (ex. KR-212FHG,KG-X)
separately. The gyro effect is not provided only in the main system
of transmitter.
33
Movement range
Operation position
Center Low position
2 steps
100 steps
LOW Maximum
3 ・ 4CH