Table of Contents
Advertisement
16P 製本 1C
Instruction manual
EX-5UR Features
Though developed as a well-balanced and controllable entry model, EX-5UR ultra high-response transmitter uses
2.4GHz as a frequency and allows simultaneous running without checking unused band. This high standard model
is widely recommended from beginners to enthusiasts. 27 functions allows you to make detailed settings for R/C
race. This set is available either "Electronic Speed Controller Set" for electric powered cars or "2-servo set" for gas R/C
cars. Refer to the instructions according to your R/C car.
Set components and cable connection
●Transmitter
(EX-5UR)
●Servo horn
●Servo grommet
●Digital servo sticker
●Receiver connector cap
MADE IN JAPAN
Thank you for purchasing EX-5UR. Please read and fully understand the instructions prior to use R/C model.
● For electric cars
●Running battery (not included)
●Servo
● For gas cars
●Servo
Caution!
When using units not included in the set, be sure to use products compatible with
"Ultra High Speed Response". Please refer to our website for details
（
w
w
w
k .
o
p
o r
p
o
c .
. o
p j
）
●Receiver (KR-407S)
●Receiver (KR-407S)
(Japanese only)
●Motor (not included)
●ESC (Speed controller)
●Receiver battery
(not included)
1
Advertisement
Table of Contents
Related Manuals for Ko Propo EX-5UR
Summary of Contents for Ko Propo EX-5UR
- Page 1 16P 製本 1C Instruction manual Thank you for purchasing EX-5UR. Please read and fully understand the instructions prior to use R/C model. EX-5UR Features Though developed as a well-balanced and controllable entry model, EX-5UR ultra high-response transmitter uses 2.4GHz as a frequency and allows simultaneous running without checking unused band. This high standard model is widely recommended from beginners to enthusiasts.
-
Page 2: For Safe Operation
■ For safe operation For safe operation With the nature of radio controlled model, improper usage may result in serious accidents. In order to avoid these circumstances, please read following contents before use. We cannot be held responsible for problems encountered when not complying with these cautions and notices. -
Page 3: Name Of Parts
Register the transmitter to the receiver to complete “pairing”←Refer to P.5 ※EX-5UR requires “pairing” to register the transmitter ID number to the receiver the first time you use. When operating several receivers (cars) using one transmitter, perform "pairing" for each receivers only first time you use. -
Page 4: Notes On Installing Receiver (Anti-Noise Measures)
■ Notes on installing receiver (anti-noise measures) Notes on installing receiver (anti-noise measures) Locate antenna cable as far away from noise source! Carbon chassis Battery Be careful of noise! Assume that all areas where large currents are flowing are generating noise! Locate antenna cables and receiver as far away from the motor, ESC, silicone cords as possible. -
Page 5: Adjusting Steering
■ Pairing／Steering／Throttle／ABS ▶How to pairing Register receiver to the transmitter 1. Forward key ＋ Back key ① Hold both Forward and Back keys and switch transmitter on. ② "PAIR" (blinking sign) will be displayed on the LCD screen and alarm sounds. ③... -
Page 6: Procedure When Running
Power on: Note surroundings and switch transmitter on, then switch receiver on. Checking model: Confirm model to be used. ※EX-5UR automatically finds unused frequency band after switching on. This function is called "carrier sense". To perform carrier sense effectively, switching on transmitter around the running area as close as possible. - Page 7 ■MENU 01∼04 Neutral position MENU01：Steering monitor ▶Displays the current position of steering. If steering direction is changed in reverse position, movement of steering and L/R will be reversed accordingly. MENU02：Steering trim Ｌ50 ∼ ０ （Default setting） ∼ Ｒ50 ▶Neutral position of steering can be adjusted while running. ET1 lever Adjust using ＋/−...
- Page 8 ■MENU 05∼07 MENU05：Steering balance L 40 ∼ 70 （Default setting） ∼ 100 ▶This function allows you to adjust left turning angle. (Use to correct left and right turning radius) + key Adjust using ＋/− keys. Push both keys together to reset. −...
- Page 9 ■MENU 08∼11 MENU08：Steering sub trim L30 ∼ 0 （Default setting） ∼ R30 ▶This function allows you to adjust the edge of operation and neutral position at the same time. (Use when installing servo and test running) + key − key Adjust using ＋/−...
- Page 10 ■MENU 12∼14 MENU12：Throttle high point 0 ∼ 70 （Default setting） ∼ 100 ▶Sets only the max forward movement on throttle. (Allows you to adjust highest point of ESC of electric car or“high”carburetor of gas car) + key − key Adjust using ＋/−...
- Page 11 ■MENU 15∼17 MENU15：Throttle curve F 50 ∼ 0 （Default setting） ∼ ＋50 ▶This function allows you to adjust throttle servo move- ment on actual trigger operation (forward only). + key Adjust using ＋/− keys. Push both keys together to reset. −...
- Page 12 ■MENU 18∼20 MENU18：Throttle reverse NORM ／ REV （Default setting） ▶You can change the direction of throttle movement (Use this function when the turning direction of servo is opposite to the transmitter operation) + key − key Adjust using ＋/− keys. Push both keys together to reset. ※REV：Reverse NORM：Normal MENU19：ABS power 0 （Default setting）...
- Page 13 ■MENU 21∼23 3ch movement MENU21：3ch monitor ▶Displays current 3ch servo movement. MENU22：Adjustment of 3ch position 127 ∼ (Each default positions) ∼ ＋127 ▶Adjusting the movement amount of 3ch servo in each position (position 01∼05) Foward key Adjust using 1. Hold + key for a while + key 2.
- Page 14 ■MENU 24∼27 Reset MENU24：Model reset ▶This will erase all data of model memory. + key Adjust using Hold + key for a while to erase ※LCD turns off when setting is finished. Caution! Memory will be reset back to the factory settings. MENU25：Model copy Copy ▶Save the current model memory to other model memory...
-
Page 15: Safety Function
sources. Change location or take some time before switching on. ②Power is not on if the LED does not shine. Reconnect receiver battery or amplifier cables. EX-5UR(transmitter) uses 2,4GHz direct sequence spread spectrum (DS-SS) as a frequency Caution! band. The frequency band is also used for electric appliances such as personal computer w/wireless LAN, Bluetooth and microwave oven. -
Page 16: After-Sales Service
■ Spec／After-sales service After-sales service Transmitter: KT-309 Current consumption: Approx. 100mAh Operation method: Wheel + trigger type Operation area: Approx. within 80m radius Number of channels: 3 channels Function: Compatible with High Speed Response (ULTRA) Frequency: 2.4GHz Receiver: KR-407S Modulation: Direct sequence spread spectrum (DS-SS) Modulation: Direct sequence spread spectrum (DS-SS)