Danfoss VLT AutomationDrive FC 302 Operating Manual page 102

Specifications
10.1.3 Electrical Data for Enclosures D1h–D8h, 3x525–690 V
®
VLT AutomationDrive FC 302
High/normal overload
(High overload=150% current during
60 s.
Normal overload=110% current during
60 s)
Typical shaft output at 525 V [kW]
Typical shaft output at 575 V [hp]
Typical shaft output at 690 V [kW]
Enclosure size
Output current (3-phase)
Continuous (at 525 V) [A]
Intermittent (60 s overload)
(at 525 V) [A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload)
(at 575/690 V) [A]
Continuous kVA (at 525 V) [kVA]
Continuous kVA (at 575 V) [kVA]
Continuous kVA (at 690 V) [kVA]
Maximum input current
Continuous (at 525 V) [A]
Continuous (at 575/690 V)
Maximum number and size of cables per phase
10 10
- Mains, motor, brake, and load share
[mm 2 (AWG)]
Maximum external mains fuses [A]
Estimated power loss at 575 V [W]
Estimated power loss at 690 V [W]
3)
Efficiency
Output frequency [Hz]
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C
(°F)]
Table 10.5 Electrical Data for Enclosures D1h/D3h/D5h/D6h, Mains Supply 3x525–690 V AC
1) For fuse ratings, see chapter 10.7 Fuses and Circuit Breakers.
2) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies for
dimensioning of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control
card power consumptions are included. For power loss data according to EN 50598-2, refer to www.danfoss.com/vltenergyefficiency. Options and
customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each add only 4 W.
3) Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy
efficiency class, see chapter 10.4 Ambient Conditions. For part load losses, see www.danfoss.com/vltenergyefficiency.
100
VLT® AutomationDrive FC 302
N55K
HO NO HO
45 55 55
60 75 75
55 75 75
76 90 90
114 99 135
73 86 86
110 95 129
69 82 82
73 86 86
87 103 103
74 87 87
70 83 83
2x95 (2x3/0) 2x95 (2x3/0)
1) 160
1098 1162 1162
2), 3)
1057 1204 1205
2), 3)
0.98
0–590
110 (230) 110 (230)
75 (167) 75 (167)
Danfoss A/S © 09/2018 All rights reserved.
N75K N90K
NO HO NO
75 75 90
100 100 125
90 90 110
D1h/D3h/D5h/D6h
113 113 137
124 170 151
108 108 131
119 162 144
103 103 125
108 108 131
129 129 157
109 109 132
104 104 126
2x95 (2x3/0)
315 315
1428 1430 1740
1477 1480 1798
0.98 0.98
0–590 0–590
110 (230)
75 (167)
± 15% (tolerance relates to variety in voltage and cable conditions). These
N110 N132
HO NO HO NO
90 110 110 132
125 150 150 200
110 132 132 160
137 162 162 201
206 178 243 221
131 155 155 192
197 171 233 211
125 147 147 183
131 154 154 191
157 185 185 230
132 156 156 193
126 149 149 185
2x95 (2x3/0) 2x95 (2x3/0)
315 315
1742 2101 2080 2649
1800 2167 2159 2740
0.98 0.98
0–590 0–590
110 (230) 110 (230)
75 (167) 75 (167)
MG34U502