Bus 2Easy Device Registration; Addressing Control Devices - FAAC B614 Manual

 9 Addressing control devices
0 0 0 0 Open A_1
0 0 0 1 Open A_2
0 0 1 0 Open A_3
0 0 1 1 Open A_4
0 1 0 0 Open A_5
0 1 0 1 Stop
0 1 1 0 Stop NC_1
0 1 1 1 Stop NC_2
1 0 0 0 Close
1 0 0 1 Open B_1
1 0 1 0 Open B_2
1 0 1 1 Open B_3
1 1 0 0 Open B_4
1 1 0 1 Open B_5
1 1 1 0 /
1 1 1 1 /
0 0 0 0 Open A_1
0 0 0 1 Open A_1
0 0 1 0 Open A_1
0 0 1 1 Open A_1
0 1 0 0 Open A_2
0 1 0 1 Open A_2
0 1 1 0 Open A_2
0 1 1 1 Open A_2
1 0 0 0 Open A_3
1 0 0 1 Open A_3
1 0 1 0 Open A_3
1 0 1 1 Open A_3
1 1 0 0 Open A_4
1 1 0 1 Open A_4
1 1 1 0 Open A_4
1 1 1 1 Open A_4
1. Register the BUS 2easy control devices (
programming).
2. Check the status of LEDs DL3 and DL7 ().
3. Check that the devices are working properly. Use
the controls to make the arm move. Check the
LEDs on the devices, the status of the bus on the
display and make sure that the automation system
operates according to the type of device installed.

BUS 2EASY DEVICE REGISTRATION

Registration is required:
- When the automation system is first started or after
the board has been replaced.
- Following any changes (addition, replacement or
removal) to the BUS 2easy devices.
B614
ON
1 2 3 4 5
1 command
DIP switch 5 = 0 (OFF)
ON
Open B_1
Open B_2
1 2 3 4 5
Stop
2 commands
Close
DIP switch 5 = 1 (ON)
Open B_1
Open B_2
Stop
Close
Open B_3
Open B_4
StopNC_1
Close
Open B_3
Open B_4
StopNC_2
Close
bu
Registration procedure:
1. Select parameter
F
is released, the display shows the status of the
BUS 2easy devices ().
2. Press and hold the
for at least 5 seconds until
flashes during this time). Registration has been
completed.
3. Release the
the status of the BUS 2easy devices
4. Check the status of the LEDs on the board:
LED DL7 (Red) - BUS 2easy devices
 
At least one device is engaged/active

No device is engaged/active
LED DL3 (Green) - BUS 2easy line
Line monitoring. LED always on (off with board in Sleep

mode)
 
Line short-circuited

Device error: check the ERROR LED
Registered device verification procedure:
1. Select parameter
registering one or more devices,
segment 13 on.
2. Press and hold the
the segments relative to the registered devices
will come on. Each segment of the display cor-
responds to a type of device:
1 Open A control device
2 Open B control device
3 Closing photocells
4 Photocells for Open impulse
5 Not used
6 Close control device
7 Not used
8 Stop control device
9 Not used
Basic
10 Not used
11 Not used
12 Not used
13 BUS 2easy status
14 Not used
44
bu
in basic programming. When
+
and - buttons simultaneously
Y
appears (the display
+
and - buttons. The display shows
bu
in basic programming. After
+
button and keep it pressed;
532297 - Rev.D
b u
displays