Xerox DOCUPRINT N4525 Service Quick Reference Manual page 63

Table 1-27 Repair Analysis Procedure (RAP) Table (cont'd.)
Displayed Error
Error Code
Message
Duplex Unit Fail H2-7
Power Off/On
Install Correct H2-8
Duplex Unit
Load Tray 1 H4-1
<size>, <type>
Load Tray 2 H4-2
<size>, <type>
Load Tray 3 H4-3
<size>, <type>
Load Tray 4 H4-4
<size>, <type>
Load Tray 5 H4-5
<size>, <type>
Finisher Failure H5-11 Failure of Finisher Bin. (SE21)
Power Off/On
Finisher Failure H5-21 Failure of Finisher Front Jogger. (SE 8)
Power Off/On
Finisher Failure H5-22 Failure of Finisher Rear Jogger. (SE 9)
Power Off/On
Finisher Failure H5-81 Failure of Exit Roller Open/Close.
Power Off/On
Finisher Failure H5-83 Failure of Roller Shift. (SE 6)
Power Off/On
Finisher Failure H5-91 Failure of Stapler. (SE 16)
Power Off/On
Finisher Failure H5-92 Failure of Stapler Head Home Sensor. (SE 16)
Power Off/On
Finisher Failure H5-93 Failure of Stapler Front Staple Position. (SE 10)
Power Off/On
Finisher Failure H5-96 Failure of Stapler Swing. (SE 11/12)
Power Off/On
Finisher Failure H6-7
Power Off/On
HCF NVM Fail H7-3
Power Off/On H7-4
H7-7
Replace Print J1-2
Cartridge
Fault Description
There is a communication problem between the
printer and the Duplex Unit.
Logic Control on the Print Engine Controller Board
could not initialize the Duplex Unit within the
specified time.
Incorrect Duplex Unit detected as being installed.
(N24/N32/N40 Duplexer Installed instead of N4525
Duplexer.). No RAP required.
Tray 1 out of paper or size/type incorrect for printed
job.
Tray 2 out of paper or size/type incorrect for printed
job.
Tray 3 out of paper or size/type incorrect for printed
job.
Tray 4 out of paper or size/type incorrect for printed
job.
Tray 5 out of paper or size/type incorrect for printed
job.
(SE 5)
Communication Error between Print Engine
Controller and Finisher Board.
There is a communication problem between the
Print Engine controller and the High Capacity
Feeder or a problem with NVM on the HCF.
NVM on the High capacity feeder control Board
cannot execute a READ/WRITE, is non-functional, or
there is a communication error between the HCF and
the Print Engine Controller Board.
The Laser Print (EP) Cartridge is low on toner
and should be replaced.
Logic Control on the Print Engine Controller Board
sensed that at Main Motor start-up, the Toner Sensor
was off for longer than the specified time.
Volume 1 / Print Engine - Error Codes & Messages
Go To Unit/
RAP Page
No.
RAP 1-93
1-38
RAP 1-94
1-39
RAP 1-95
1-40
RAP 2-401
2-16
RAP 2-403
2-17
RAP 2-404
2-18
RAP 6-696
6-23
RAP 6-698
6-24
RAP 6-699
6-25
RAP 6-700
6-26
RAP 6-702
6-27
RAP 6-704
6-28
RAP 6-705
6-29
RAP 6-707
6-30
RAP 6-709
6-31
RAP 6-710
6-32
RAP 2-406
2-19
RAP 1-96
1-41
1-41