Lightware VINX-120-HDMI-ENC User Manual page 99

   
10. Appendix
Bugfix:
▪ Fixed a bug that caused the video not to be transmitted properly
in Unicast mode when switching Video Stream ID on the encoder.
▪ Fixed a bug that caused the Auto detect from EDID scaler feature
not to work properly after a factory reset.
▪ Fixed a bug that caused the device to switch to Unicast mode from
Multicast mode only at the second click on the corresponding
button on the Advanced Settings page.
▪ Fixed a bug that let the user select two decoders to receive the
same video stream in Unicast mode.
▪ Fixed a bug that caused the connection to the device to be lost
when changing Video Stream ID on the decoder multiple times in
rapid succession.
▪ FixedabugthatcausedtheUSBLEDonthedecodernottoreflect
valid information when pressing the Connect button on several
decoders connected to the same encoder in rapid successions
multiple times.
▪ Added a warning message to state that the device having an Auto
IPof169.254.x.xcannotbedetectedafterfirmwareupgradeas
the IP address will change after a reboot.
▪ Fixed a bug that caused the Delete video wall button on the
VideoWallSetuppagetobeactiveevenifthereisnovideowall
selected.
▪ Fixed a bug that let the user enter invalid value for stop bit in the
LW3treeview.
▪ Fixed a bug that caused the IGMP packets to be disregarded by
certain switches due to missing Router Alert option from the
IP header. Thus, it is no longer necessary to disable IP header
validation on the switches.
▪ Fixed a bug that caused connection reset during firmware
upgradebyLDU2.
▪ FixedabugthatcausedtheProgrammers'LW3Terminalwindow
to be rendered incorrectly at certain resolutions.
Known issue:
▪ The video wall being edited can lose focus when it is saved.
▪ The Output scaling radio button group works hectically when the
Output standard is set to DVI.
v1.1.1b2
Release date: 2018-06-07
Bugfix:
▪ Fixed a bug that degraded switching speed.
VINX-1x0-HDMIExtenders–User'sManual
v1.1.0b7
Releasedate:2018-05-31
New feature:
▪ From this version on, the items in the Emulated EDID on input list
reflectthemonitornamefieldoftheEDIDinsteadoftheformat
parametersforbetteridentification.
▪ New EDIDs have been added to the factory EDID list.
▪ From this version on, the OSD messages that appear on the
display connected to the VINX decoder are turned off by default.
They can be turned on individually or globally, though.
▪ From this version on, information like the IP address of a decoder
and the position within a video wall can be temporarily displayed
on the monitor attached to a VINX decoder. This will ease the
setup of video walls.
▪ For smooth video playback, the default operation mode has been
changed from Graphic Mode to Video Mode.
▪ From this version on, VINX encoder and decoder units can be
upgradedinbatchesbyLDU2.
▪ Itisnowpossibletodisable(byanLW3property)theDIPswitch
setting of the video stream ID.
▪ Version number of several components including package
version has been added to the graphical user interface.
▪ It is now possible to set bandwidth limit for the encoded video
stream generated by the encoder.
▪ It is now possible to create a list of favourite channels and
associate shortcut keys to cycle through the list up and down.
Moreover,shortcutkeyscanbeassociatedwithspecificstreams.
The associated shortcut key, when pressed on a keyboard
attached to a decoder, can be used to trigger the corrsponding
action.
▪ It is now possible to connect to an encoder from a decoder or to
a decoder from an encoder by clicking on a Connect button in the
list of available devices on the Main Settings page.
Bugfix:
▪ Fixed a bug that caused VINX-HDMI-120-ENC and VINX-HDMI-110-
DECnottobeaccessibleviahttp://lwr-gatewayAABBCCDDEEFF.
local or http://lwr-clientAABBCCDDEEFF.local, respectively,
where AABBCCDDEEFF is the MAC address without colons of
the device to be accessed.
▪ Fixed a bug that caused a decoder device to display invalid
content when it was removed from a video wall.
Appliedfirmwarepackage:v2.0.2b4 | LDCsoftware:v2.5.2b3
▪ Fixed a bug that casued the VINX encoder to restart when the
corresponding decoder was reading an EDID from the attached
device that had a Video Format Preference block in its CEA
extension.
▪ Fixed a bug that caused the RS-232 symbol rate not to be
displayedcorrectlywhenacustomvaluewassetviaLW3.
▪ Known issue:
▪ When defining a shortcut key combination for switching to
previous or next stream or for a stream shortcut, and the shortcut
keycombinationhasmoremodifierkeys,theboxcontainingthe
key combination might get truncated.
▪ When an encoder is switched to Unicast mode and restarted,
it still can receive the USB stream coming from a decoder in
Multicast mode and having the same Video Stream ID.
▪ The Programmers' LW3 Terminal window might get rendered
incorrectly at certain resolutions.
▪ Whendraggedatcertainpixelpositionsitisimpossibletomove
an item from the tile representing a video wall element on the
VideoWallSetuppage.
▪ Switching source or destination through the Device list pane on
the Main Settings page of the encoder or decoder might take
more time compared to switching directly by modifying the ID in
the Video stream ID box.
Known issue:
▪ When defining a shortcut key combination for switching to
previous or next stream or for a stream shortcut, and the shortcut
keycombinationhasmoremodifierkeys,theboxcontainingthe
key combination might get truncated.
▪ When an encoder is switched to Unicast mode and restarted,
it still can receive the USB stream coming from a decoder in
Multicast mode and having the same Video Stream ID.
▪ The Programmers' LW3 Terminal window might get rendered
incorrectly at certain resolutions.
▪ Whendraggedatcertainpixelpositionsitisimpossibletomove
an item from the tile representing a video wall element on the
VideoWallSetuppage.
▪ Switching source or destination through the Device list pane on
the Main Settings page of the encoder or decoder might take
more time compared to switching directly by modifying the ID in
the Video stream ID box.
v1.0.0b11
Releasedate:2017-12-14
99