Bosch DS7200V2-UK Installer's Manual page 138

Groups:
Handshake:
Instant Alarm:
Keyfob:
Keyswitch:
Latching:
Location:
No Entry:
Off Display:
Options:
PSTN:
Parity:
Parameter:
Partial On:
Perimeter Only:
PIN:
Restoral Report:
RPS:
Sked:
Swinger Shunt:
Tamper
Trouble:
Visible Zone:
Zone:
Zone Function:
Zone Type:
Page 138 P/N: 4998152533-02
PART V: REFRENCE MATERIALS
The programming parameters described in this manual are organized into groups. Most groups primarily
contain parameters that are related in some way. For example, the Authority Levels Group contains
parameters that configure the panel's four Authority Levels.
A signal sent by one end of the communications channel to the other indicating reception of signal.
A zone type that initiates an alarm immediately when faulted. This zone type does not follow any
Entry/Exit delay time.
A small, hand-held wireless device usually designed to fit on a key chain. It consists of buttons that allow
the user to perform various functions, depending on the keyfob, such as arming/disarming the system,
operating outputs or sending reports.
Two types: Momentary and Maintained. To operate a Momentary Keyswitch , insert the key, turn it and
release it. The key returns to its starting position automatically. The key cannot be removed unless it is in
the starting position. A Maintained Keyswitch typically has two positions marked "Armed" and
"Disarmed." To operate, insert the key, turn to desired position and remove the key.
The locking in of a circuit by means of a holding contact.
A Location represents the following parameter assignments: Area, Zone Number and Device. A Location
tells the panel in which Area a device is assigned and by which Zone Number it reports as.
Turning the system on without Entry Delay.
The display that appears when the system is turned off and no keys are pressed (normal display).
Options are a unique type of parameter that allows the installer to configure up to four features by
entering a Data Digit at a single Address.
P ublic S witched T elephone N etwork. An assembly of communications facilities and central office
equipment operated jointly by authorized common carriers that provides the general public with the
ability to establish communications channels via discrete dialing codes.
A method of checking the accuracy of transmitted data by adding an extra bit to the number when
necessary to make the number odd or even.
Each program parameter sets a specific value or chooses an option.
A user-defined subset of the zones that arm. Partial On with No Entry (Instant) is an option
An installer-defined subset of the zones that arm. Perimeter Only with No Entry (Instant) is an option.
P ersonal I dentification N umber. A unique number issued at the time of installation of each system. This
PIN is required to operate the system (arm/disarm, test system, initiate functions, etc.). The PIN is not
the same as the account number.
A signal transmitted upon the removal of a trouble or alarm condition from a zone.
RPS International is a Windows
remotely set up and program specific control panels.
A scheduling parameter that allows a selected event to happen at a specific time.
A programmable feature that determines the number of alarms or troubles the zone can transmit. If the
number is exceeded, the zone is bypassed for the remainder of the arming period.
Tamper conditions can be generated several different ways. A tamper-wired zone can report tamper
because the zone is open or shorted. An RF transmitter can report a zone tamper because its case was
tampered. A zone can be configured as a tamper zone. An off-normal tamper zone is a tamper condition.
Different hardware devices can report tamper, including the keypads, the DX2010 zone expanders, and
the RF3224E or RF3227E receivers.
A service condition that needs to be corrected, such as a broken wire.
A zone that displays at keypads during alarm or trouble conditions.
The panel reports changing conditions on the sensor loops as Zone events. For example, when the
condition on On-board Sensor Loop 1 changes from Normal (supervised EOL resistor in place) to
Shorted, the panel can be programmed to create an alarm event for Zone 1. That alarm event appears in
keypad displays as "Alarm, Zn 1." If programmed for reporting, the panel would send an "Alarm, Zn 1"
report to the ARC receiver in the programmed reporting format.
Use to construct "personality types" for zones used in the panel. Each unique Zone Function
Configuration determines responses to specific conditions occurring on the zones.
Describes what the zone does. For example, Fire zone, Burglar zone, 24-hour zone, etc.
Copyright  2007 Bosch Security Systems, Inc.

-based account management and panel programming utility designed to
DS7200V2-UK Installer's Guide