ADT Unimode 9600 Installation And Operating Instruction
  1. Manuals
  2. Brands
  3. ADT Manuals
  4. Control Panel
  5. Unimode 9600
  6. Installation and operating instruction
ADT Unimode 9600 Installation And Operating Instruction

ADT Unimode 9600 Installation And Operating Instruction

Adt addressable fire alarm control panel programming, installation, maintenance and operating instruction manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Unimode 9600
Addressable Fire Alarm Control Panel
Programming, Installation, Maintenance
and Operating Instruction Manual
IMPORTANT! The Signaling Line Circuit Wiring Manual Document #51520 must be referenced in
addition to this manual when installing or servicing the Fire Alarm Control Panel.
ADT Security Services, Inc.
One Town Center Road
Boca Raton, FL 33431
Phone: (561) 988-3600
FAX: (561) 988-3675
Document
#51336
11/06/01
Revision:
P/N 51336:C
ECN 01-535
C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Unimode 9600 and is the answer not in the manual?

Questions and answers

Related Manuals for ADT Unimode 9600

Summary of Contents for ADT Unimode 9600

  • Page 1 Operating Instruction Manual IMPORTANT! The Signaling Line Circuit Wiring Manual Document #51520 must be referenced in addition to this manual when installing or servicing the Fire Alarm Control Panel. ADT Security Services, Inc. One Town Center Road Boca Raton, FL 33431...

  • Page 2: Fire Alarm System Limitations

    Fire Alarm System Limitations An automatic fire alarm system–typically made up of smoke detectors, heat detectors, manual pull stations, audible warn- ing devices, and a fire alarm control with remote notification capability–can provide early warning of a developing fire. Such a system, however, does not assure protection against property damage or loss of life resulting from a fire.

  • Page 3: Installation Precautions

    Installation Precautions WARNING - Several different sources of power can be con- nected to the fire alarm control panel. Disconnect all sources of power before servicing. Control unit and associated equip- ment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized.
  • Page 4 Notes Unimode 9600 PN 51336:C 11/06/01...

  • Page 5: Table Of Contents

    3.5: Programming and Passwords ...40 3.6: Master Programming Level...42 3.6.1: Point Program ...43 3.6.1.1 Detector Programming ...43 3.6.1.1.1 Add Detector ...43 3.6.1.1.2 Delete Detector ...44 3.6.1.1.3 Edit Detector ...44 3.6.1.2 Module Programming ...53 Unimode 9600 P/N: 51336:C 11/06/01 Table of Contents...
  • Page 6 3.6.9: Option Modules...91 3.6.9.1 Annunciators/UDACT ...91 3.6.9.2 Printer/PC ...92 3.6.10: Password Change ...93 3.6.11: Clear Program...94 3.6.12: Program Check...95 3.7: Maintenance Programming Level ...97 3.7.1: Disable Point ...98 3.7.2: History...99 3.7.3: Program Check...100 3.7.4: Walktest ...101 Unimode 9600 P/N: 51336:C 11/06/01...
  • Page 7 5.2: Calculating the AC Branch Circuit ...127 5.3: Calculating the System Current Draw...128 5.3.1: Overview ...128 5.3.2: How to Use Table 5.3 on page 129 to Calculate System Current Draw ...128 5.4: Calculating the Battery Size ...130 Unimode 9600 P/N: 51336:C 11/06/01...
  • Page 8 Table of Contents 5.4.1: NFPA Battery Requirements ...130 5.4.2: Selecting and Locating Batteries...130 APPENDIX A: Software Zones ...131 A.1: Correlations ...131 APPENDIX B: Default Programming ...139 APPENDIX C: Wire Requirements ...140 Unimode 9600 P/N: 51336:C 11/06/01...
  • Page 9 ADT-AFM-16A Annunciator ADT-ACS Series Annunciators ADT-UDACT Communicator/Transmitter ADT-CHG-120 Battery Charger ADT-LDM Series Lamp Driver Modules LCD-80F Remote Fire Annunciator ADT-ACM-8R Relay Control Module Unimode 9600 PN 51336:C 11/06/01 Document #51352 Document #51520 Document #A15048 Document #A15207 Document #51353 Document #50934...
  • Page 10 Unimode 9600 PN 51336:C 11/06/01...
  • Page 11 Doc. # 50934 TERM (EIA-485) Annunciators Unimode 9600 Doc. # 51336 SLC Loop Battery Connector ADT-CHG-120 Charger Doc. # 50938 Unimode 9600 PN 51336:C 11/06/01 ADT-AFM-16AT & ADT-ACS Series ADT-AFM-32A Doc. # 51353 Doc. # A15048 ADT-AFM-16A Doc. # A15207 Drill...

  • Page 12: Section 1: Product Description

    SLC expansion module, local and remote upload/download software and remote power expansion. 1.1 Inventory When the Unimode 9600 shipment is received, check to make certain that all parts have been included in the shipment. The Unimode 9600 shipment should consist of one of each of the following: ✓...
  • Page 13 ✓ SD300(T): addressable Photoelectric Smoke Detector (T= Thermal Sensor) ✓ C304: Control Module ✓ M300: Monitor Module ✓ M301: Miniature Monitor Module ✓ M302: 2-wire Detector Module ✓ ADT-BG-10LX: Manual Pull Station • Optional 4XTMF module (conventional reverse polarity/city box transmitter) Unimode 9600 PN 51336:C 11/06/01 Product Description...

  • Page 14: Specifications

    Maximum Charging Circuit: Normal Flat Charge - 27.6 VDC @ 1.00 amp Maximum Battery Charger Capacity: 25 Amp Hour (Unimode 9600 cabinet holds maximum of two 18 Amp Hour batteries. For greater than 25 Amp Hour up to 120 Amp Hour batteries, use the ADT-CHG-120 Battery Charger and BB-55F Battery Box.

  • Page 15: 1: Current Availability

    NAC # 1 per circuit 3 amps max NAC # 2 per circuit Refer to the battery calculations section for additional information. Unimode 9600 PN 51336:C 11/06/01 Standby 6 amps max per panel Figure 1.1 Current Availability Product Description Alarm...

  • Page 16: Controls And Indicators

    Controls and Indicators SYSTEM ALL NORMAL 10:00A 010101 AC POWER MAINTENANCE ALARM FIRE ALARM SILENCED SUPERVISORY DISABLED TROUBLE BATTERY GROUND ACK/STEP EVENT ALARM SILENCE ENTER DRILL HOLD 2 SEC MODE RESET RECALL Figure 1.2 Membrane/Display Panel Unimode 9600 PN 51336:C 11/06/01...

  • Page 17: Circuits

    Optional modules plug in and are mounted to the main circuit board. The circuit board is delivered in the Unimode 9600 kit and must be mounted to the backbox. Refer to the circuit board illustration on Page 10.

  • Page 18: 1: Intelligent Addressable Detectors: Newer Series

    Product Description Cabinet The Unimode 9600 cabinet is red with a navy blue front overlay. The backbox provides space for two batteries (up to 18 Amp Hour). Ample knockouts are provided for system wiring. Also included is a standard dress panel, which mounts to the inside of the cabinet (required on the ULC version).

  • Page 19: 2: Intelligent Addressable Modules: Newer Series

    The ADT-BG-12LX is an addressable manual pull station featuring a key-lock reset. The pull station responds to an address set by the installer using the built-in rotary decimal switches on the pull station. The manual pull station includes an ADT key. Unimode 9600 PN 51336:C 11/06/01 Product Description...

  • Page 20: 3: 300 Series Intelligent Addressable Devices

    SLC-2 Expander Module The SLC-2 Expander Module allows expansion of the Unimode 9600 from one SLC circuit to two SLC circuits. The module plugs into connector J3 which is located in the lower right corner of the main circuit board.

  • Page 21: Accessories

    IBM compatible computers, including laptops and portables, equipped with a serial port. Unimode 9600 program files can also be created and stored on the PC and then downloaded to the control panel. The PK-9600 Kit includes the Windows-based Programming Utility software on CD-ROM with on-line help file.

  • Page 22: 4: Adt-Chg-120 Battery Charger

    The ADT-CHG-120 is capable of charging up to 120 AH lead-acid batteries with the Unimode 9600 FACP. The FACP battery charger must be disabled when using the ADT-CHG-120. The batteries and charger can be housed in the BB-55F battery box which can be mounted up to 20 feet away from the control panel.

  • Page 23: Getting Started

    Enter Autoprogramming (refer to "Autoprogram" on page 87) • Resolve Programming Conflicts Go to Point Program to Enter Specific Data (refer to "Point Program" on page 43). Use the right and left arrow keys to navigate between devices. Unimode 9600 PN 51336:C 11/06/01 Product Description...

  • Page 24: Section 2: Installation

    ✓ Secure the circuit board to the standoffs with the supplied screws and male/ female standoff as indicated in following figure IMPORTANT! Secure circuit board to this standoff with supplied male/female standoff mounting studs Figure 2.1 Unimode 9600 Main Circuit Board Installation Unimode 9600 Main Circuit Board CUT TO DISABLE LOCAL CHARGER...
  • Page 25 1.50“ (3.81 cm) 1.75“ 4.45 cm Unimode 9600 PN 51336:C 11/06/01 2.00“ 2.00“ 2.00“ 2.00“ 2.00“ 15.5“ (39.37 cm) 12.00“ (30.48 cm) Figure 2.2 Unimode 9600 Cabinet Mounting Installation 4.45 cm 1.75“ 3.81 cm 1.50“ 4.1cm 1.62“ 47.0cm 18.5“ 4.45cm 1.75“...
  • Page 26 21.620" 18.625" (54.92 cm) (47.308 cm) Trim Ring P/N:FC-TR Figure 2.3 Unimode 9600 Cabinet Dimensions Depth = 4.37" (11.1 cm) Door = 15.78" (40.08 cm) Backbox = 15.5" (39.37 cm) Battery Box = 8.5" (21.59 cm) Battery Box = 14.34" (36.42 cm)

  • Page 27: Power

    3.0 amperes max., 24 VDC nominal filtered, resettable power can be drawn from TB3 Terminals 1(+) and 2(-) Unimode 9600 PN 51336:C 11/06/01 ) or larger wire with 600 volt Power-limited Nonresettable Power #1 3.0 amperes max. , 24 VDC nominal...

  • Page 28: Relays

    Style Y (Class B) Notification Appliance Circuit, supervised and power-limited - 4.7 kohm, ½ watt P/N:71252 UL listed Polarized Bell Polarized Horn Polarized Horn Dummy Load all unused circuit B+ A+ A- B- B+ A+ A- B- Figure 2.6 NAC Connections Relays Unimode 9600 PN 51336:C 11/06/01...

  • Page 29: Ul Power-Limited Wiring Requirements

    A typical wiring diagram for the Unimode 9600 is shown below. Figure 2.7 Typical UL Power-limited Wiring Requirements Unimode 9600 PN 51336:C 11/06/01...

  • Page 30: Optional Modules And Devices

    OPT DACT CUT TO ENTER MONITOR 4XTM DRILL HOLD 2 SEC LCD DISPLAY MODE KEYPAD I/F RESET RECALL NEUT EARTH +BATTERY- Mounting Screw Access Holes Figure 2.8 Keypad/Display Removal Unimode 9600 PN 51336:C 11/06/01 Optional Modules and Devices OPT SLC...

  • Page 31: 1: 4Xtmf Transmitter Module Installation

    Before installing the module, place the disconnect switch to the right (disconnect) position to prevent accidental activation of the municipal box. Note that a Disconnect LED will illuminate after the module is installed in the Unimode 9600. In addition, the System Trouble LED will turn on to indicate the Disconnect condition.

  • Page 32: 2: Auxiliary Trouble Input (J16 & J17)

    Unimode 9600 Figure 2.10 4XTMF Connectors to Unimode 9600 Connectors NOTE: Jumper JP5 on the Unimode 9600 main circuit board can be used to configure the FACP supervisory relay for operation with the 4XTMF module. The supervisory relay must be programmed as shown on the main circuit board silkscreen (TB5, Terminals 4, 5 &...

  • Page 33: 3: Slc-2 Expander Module

    2.6.3 SLC-2 Expander Module The optional SLC-2 Expander Module provides a second SLC loop for the Unimode 9600 control panel. This allows connection of an additional 318 addressable devices, bringing the total to 636 addressable devices which can be connected to the FACP. Refer to the SLC Manual for information on connecting devices to the SLC.

  • Page 34: 4: Printer/Pc

    FACP to communicate with the device. CAUTION! Do not connect a printer or PC to the Unimode 9600 FACP if a ground fault exists on the control panel. Circuit damage may result. Remove all power (AC and DC) before installing or removing any wiring.

  • Page 35: 5: Digital Communicator And Annunciators

    2.6.5.2 ADT-ACM-8R Relay Control Module Reference Manual 2.6.5.3 BRKT-9600 Universal Bracket Installation CUT TO DISABLE LOCAL CHARGER JP10 DISABLE Unimode 9600 Cabinet Figure 2.13 BRKT-9600 Bracket Installation 4XTM OPT BD JP11 AC POWER M AINTE NAN CE ALARM FIRE ALARM SILENCED SUPERVISORY...
  • Page 36 ✓ ADT-UDACT Digital Alarm Communicator/Transmitter - installs at standoff location (A) ✓ ADT-ACM-8R Annunciator Control Module (Relay) - installs at standoff location (A) 1. Install the two supplied standoffs in location (A) as indicated in Step 1 of the following illustration 2.

  • Page 37: Adt-Acs And Adt-Afm Series Annunciators

    2.6.5.4 ADT-ACS and ADT-AFM Series Annunciators ADT-ACS Annunciator Address Annunciator Displays the Following Points 8 General System Status Points & Zones 1 - 56 Zones 57 - 99 & 2 NACs Loop 1, Module Addresses 1 - 64 Loop 2, Module Addresses 1 - 64 Loop 1, Module Addresses 65 - 128 Loop 2, Module Addresses 65 - 128 Loop 1, Module Addresses 129 - 159 &...

  • Page 38: Section 3: Programming

    The keyboard can be connected to the PS-2 connector J7 on the control panel main circuit board. The information presented in this section refers to programming the Unimode 9600 via the onboard keypad. If an optional computer keyboard is connected to the Unimode 9600 main circuit board, the following table describes the keyboard keys which correspond to the onboard keypad keys.

  • Page 39: User Programming

    3.2 User Programming The Unimode 9600 is completely field programmable and requires no special software skills. While programming the Unimode 9600, the fire protection capabilities of the ! ! ! control panel are enabled. Site-specific programming may be accomplished in three ways: •...

  • Page 40: Initial Power-Up

    User Programming Levels There are two user programming levels: • User Master Program Level 1 is used for programming panel specific data relating to device types, zoning, messages, control panel functions, etc. • User Maintenance Program Level 2 is used by a qualified operator to access features such as Disable/Enable, View and Clear History, Walktest and System Time Change.
  • Page 41 To access user Programming mode, press the Enter or Mode key. The LCD will display the following: 1=READ@STATUS 2=PROGRAMMING To enter the user Programming mode, press 2. The display will read as follows: PROGRAMMING ENTER@PASSWORD ***** Entering the Master level password (default 00000) will cause the following screen to appear: @@@@PROGRAMMING 1=POINT@PROGRAM...

  • Page 42: Master Programming Level

    3.6 Master Programming Level When the Master Program Level password is entered, the control panel will enter user Programming mode. In this mode, the piezo sounder remains off, the trouble relay is activated and the system Trouble LED flashes until Programming mode is exited. The following display will appear: The down arrow which appears in the display indicates that additional programming choices can be viewed by pressing the down arrow key on the keypad.

  • Page 43: 1: Point Program

    3.6.1 Point Program PROGRAMMING The Point Program option allows the programmer to add a new addressable device to an 1=POINT PROGRAM SLC loop, delete an existing device from a loop or change the programming for an 2=ZONE SETUP existing device. Pressing 1, while viewing Programming Screen #1, will select the Point 3=LOOP SETUP Program option and display the following screen: Programming Screen #1...

  • Page 44: Delete Detector

    3.6.1.1.2 Delete Detector DETECTOR 1=ADD 2=DELETE 3=EDIT Detector Screen 3.6.1.1.3 Edit Detector @@@@ADD@DETECTOR DETECTOR#@@@@@@@005 IS@ADDED @@DELETE@DETECTOR ENTER@DETECTOR# Delete Detector Screen @@DELETE@DETECTOR DETECTOR#@@@@@@@005 IS@DELETED @@EDIT@DETECTOR ENTER@POINT@ADDRESS Edit Detector Screen...
  • Page 45 @@@@NO@DETECTOR @@@@@INSTALLED Edit Detector Screen #1 @TROUBL@SMOKE(PHOTO) @******************** @@@@@@@@@@@@@@@ZNNN @@@@@@@@@@@*@@@@1D017 Edit Detector Screen #1 @NORMAL@SMOKE@(PHOTO) @********************* @@@@@@@@@@@@@@@@ZNNN @@@@@@@@@@@@@V@@@1D017 Edit Detector Screen #1 ✓ Normal - indicates that the detector with the selected address is physically installed on the SLC and communicating with the control panel (enabled) ✓...
  • Page 46 address 017, located on the first SLC loop: EDIT DETECTOR 1=ENABLED 2=TYPE 3=VERIFICATION Edit Detector Screen #2 EDIT@DETECTOR@1D017 1=ENABLED@@@@@@@@YES 2=TYPE@@SMOKE(PHOTO) 3=VERIFICATION@@@OFF Edit Detector Screen #2 EDIT@DETECTOR@1D017 1=WALKTEST@@@@@@@@NO 2=PAS@@@@@@@@@@@@@NO 3=PRE-SIGNAL@@@@@@NO Edit Detector Screen #3 EDIT@DETECTOR@1D017 1=ZONE@ASSIGNMENT @@@@00@**@**@**@** Edit Detector Screen #4 EDIT@DETECTOR@1D017 1=NOUN/ADJECTIVE 2=DESCRIPTION...
  • Page 47 EDIT DETECTOR 1=ENABLED 2=TYPE 3=VERIFICATION Edit Detector Screen #2 See Page EDIT DETECTOR 1=WALKTEST 2=PAS 3=PRE-SIGNAL Edit Detector Screen #3 See Page @@@DETECTOR@TYPE 1=SMOKE(PHOTO) 2=SMOKE@(ION) 3=HEAT Detector Type Screen #1 @@@DETECTOR@TYPE 1=SMOKE-DUCT-P 2=SUPERV@DUCTP Detector Type Screen #2...
  • Page 48 ✓ Select PAS Yes when editing the detector set to address 005 ✓ Program the desired zone or zones to be activated by this detector, in this example Z001 ✓ Program an output, such as a control module that is to be activated by detector 005 by assigning the same zone to it;...

  • Page 49: Zone@Assignment

    EDIT DETECTOR 1=ZONE ASSIGNMENT 00 ** ** ** ** Edit Detector Screen #4 See Page EDIT DETECTOR 1=NOUN/ADJECTIVE 2=DESCRIPTION ***************** Edit Detector Screen #5 @@ZONE@ASSIGNMENT Z00@Z**@Z**@Z**@Z** Zone Assignment Screen 1=STANDARD@ADJECTIVE 2=STANDARD@NOUN 3=CUSTOM@ADJECTIVE 4=CUSTOM@NOUN Noun/Adjective Screen...
  • Page 50 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE to be used as a descriptor for the location of the detector currently being programmed. 4=CUSTOM NOUN When an adjective has been selected, it will appear at the top of the display as Noun/Adjective Screen indicated by the asterisks.
  • Page 51 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE as a descriptor for the location of the detector currently being programmed. When a 4=CUSTOM NOUN noun has been selected, it will appear at the top of the display as indicated by the Noun/Adjective Screen asterisks.
  • Page 52 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN Noun/Adjective Screen EDIT DETECTOR 1=NOUN/ADJECTIVE 2=DESCRIPTION Edit Detector Screen #5 • If the zero key is pressed, a 0 is placed in the first letter position • If the zero key is then pressed a second time with no intervening key actions, the entire field is replaced with the field entered for the previous device programmed, and the cursor moves to the last character of the field (Recall function).

  • Page 53: Module Programming

    1. The cursor is on the first letter of the Adjective field. Press the zero key twice to display FLR_3 2. With the cursor on the first letter of the Noun field, press the zero key twice to recall the display ROOM_304. The cursor automatically jumps from the first to the last letter of the Noun field 3.

  • Page 54: Delete Module

    3.6.1.2.2 Delete Module MODULES 1=ADD 2=DELETE 3=EDIT Modules Screen 3.6.1.2.3 Edit Module Screen for Monitor Module @@@@@@ADD@MODULE MODULE#@@@@@@@@@005 IS@ADDED Add Module Screen #3 @@DELETE@MODULE ENTER@MODULE# Delete Module Screen @@DELETE@MODULE MODULE#@@@@@@@@@005 IS@DELETED @@@@EDIT@MODULE ENTER@MODULE@ADDRESS Edit Module Screen...
  • Page 55 @@@@@NO@MODULE @@@@@INSTALLED @TROUBL@MONITOR @@@@@@<ADJ><NOUN> @@@@@@@@@@@@@@@@ZNNN @@@@@@@@@@@@@@@1M012 @NORMAL@MONITOR @@@@@@@<ADJ><NOUN> @@@@@@@@@@@@@@@@@ZNNN @@@@@@@@@@@@@@@@1M012 ✓ Normal - indicates that the module with the selected address is physically installed on the SLC and communicating with the control panel (enabled) ✓ <ADJ><NOUN> - represents the adjective and noun, which have been programmed, describing the location of the displayed device ✓...
  • Page 56 @NORMAL@MONITOR @@@@@@<ADJ><NOUN> @@@@@@@@@@@@@@@@@ZNNN @@@@@@@@@@@@@@@@1M012 EDIT@MONITOR@@1M012 1=ENABLED@@@@@@@@YES 2=TYPE@@MONITOR Edit Monitor Screen #2 EDIT@MONITOR@@1M012 1=PRE-SIGNAL@@@@@@NO 2=PAS@@@@@@@@@@@@@NO Edit Monitor Screen #3 EDIT@MONITOR@@1M012 1=WALKTEST@@@@@@@YES 2=ZONE@ASSIGNMENT 00@**@**@**@** Edit Monitor Screen #4 EDIT@MONITOR@@1M012 1=ADJECTIVE/NOUN 2=DESCRIPTION ******************** Edit Monitor Screen #5...
  • Page 57 (QDEOH'LVDEOH 0RGXOH (QDEOHG 1R 7\SH 0RQLWRU EDIT MONITOR 1=ENABLED 2=TYPE MONITOR Edit Monitor Screen #2 @@@MONITOR@TYPE 1=PULL-STATION 2=USER-DEFINED-1 3=WATERFLOW Monitor Type Screen #1 @@@MONITOR@TYPE 1=USER-DEFINED-2 2=MONITOR 3=BLANK Monitor Type Screen #2 @@@MONITOR@TYPE 1=USER-DEFINED-3 2=FUTURE USE 3=USER-DEFINED-4 Monitor Type Screen #3 @@@MONITOR@TYPE 1=SMOKE-CONVENTIONAL 2=HEAT-DETECTOR...
  • Page 58 @@@@MONITOR@TYPE 1=POWER-MONITOR 2=TROUBLE-MONITOR 3=USER-DEFINED-12 Monitor Type Screen #9 @@@@MONITOR@TYPE 1=PROC-MON 2=PROCMON-AR 3=USER-DEFINED-13 Monitor Type Screen #10 Note: For the PROCMON-AR selection, PROCMON refers to Process Monitor and AR refers to AutoResettable Monitor Type Pull-Station User-Defined-1 Waterflow User-Defined-2 Monitor Blank User-Defined-3 Future Use User-Defined-4 Smoke-Conventional...
  • Page 59 EDIT MONITOR 1=PRE-SIGNAL To enable the Pre-signal feature, press 1 while viewing Edit Monitor Screen #3 until 2=PAS the display reads Pre-signal Yes. Each press of the 1 key will cause the display to toggle between Pre-signal Yes and Pre-signal No. Refer to "Presignal" on page 113 for Edit Monitor Screen #3 additional information.
  • Page 60 Pressing 1 while viewing the Noun/Adjective Screen will cause the following 1=STANDARD ADJECTIVE screen(s) to be displayed. Note that the keyboard down arrow key must be pressed to 2=STANDARD NOUN see all the Adjective screens. Press the number corresponding to the adjective that is 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN to be used as a descriptor for the location of the monitor module currently being...
  • Page 61 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE as a descriptor for the location of the monitor module currently being programmed. 4=CUSTOM NOUN Noun/Adjective Screen ********************** 1=BASEMENT 2=BOILER@RM 3=CLASSROOM Noun Screen #1 ********************** 1=CLOSET 2=CORRIDOR 3=ELECTRIC@RM Noun Screen #2 ********************** 1=ELEVATOR 2=ENTRANCE 3=FLOOR Noun Screen #3 **********************...
  • Page 62 EDIT MONITOR 1=NOUN/ADJECTIVE 2=DESCRIPTION ***************** Edit Monitor Screen #4 • If the zero key is pressed, a 0 is placed in the first letter position • If the zero key is then pressed a second time with no intervening key actions, the entire Adjective field is replaced with the field entered for the previous device programmed, and the cursor moves to the last character of the field (Recall function).

  • Page 63: Edit Module Screen For Control Modules

    1. The cursor is on the first letter of the Adjective field. Press the zero key twice to display FLR_3 2. With the cursor on the first letter of the Noun field, press the zero key twice to recall the display ROOM_304. The cursor automatically jumps from the first to the last letter of the Noun field 3.
  • Page 64 EDIT CONTROL 1=ENABLED 2=TYPE 3=SILENCEABLE Edit Control Screen #2 EDIT@CONTROL 1=ENABLED@@@@@@@@YES 2=TYPE@@CONTROL 3=SILENCEABLE@@@@YES Edit Control Screen #2 EDIT@CONTROL 1=WALKTEST@@@@@@@YES 2=ZONE@ASSIGNMENT 00@**@**@**@** Edit Control Screen #3 EDIT@CONTROL 1=NOUN/ADJECTIVE 2=DESCRIPTION ******************** Edit Control Screen #4...
  • Page 65 @@@CONTROL@TYPE 1=BLANK 2=BELL-CIRCUIT 3=HORN-CIRCUIT Control Type Screen #1 @@@CONTROL@TYPE 1=SOUNDERS 2=RELAY-1FC 3=STROBE-CKT Control Type Screen #2 @@@CONTROL@TYPE 1=CONTROL Control Type Screen #3 Control Type Special Function Blank None Bell Circuit None Horn Circuit None Sounders None Relay Ignore Open Circuit Strobe Circuit None Control...
  • Page 66 EDIT CONTROL 1=WALKTEST 2=ZONE ASSIGNMENT 00 ** ** ** ** Edit Control Screen #3 EDIT CONTROL 1=NOUN/ADJECTIVE 2=DESCRIPTION Edit Control Screen #4 @@ZONE@ASSIGNMENT Z00@Z**@Z**@Z**@Z** Zone Assignment Screen 1=STANDARD@ADJECTIVE 2=STANDARD@NOUN 3=CUSTOM@ADJECTIVE 4=CUSTOM@NOUN Noun/Adjective Screen...
  • Page 67 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN to be used as a descriptor for the location of the control module currently being Noun/Adjective Screen programmed. ********************** 1=NORTH 2=SOUTH 3=EAST Adjective Screen #1 ********************** 1=WEST 2=FRONT 3=CENTER Adjective Screen #2 ********************** 1=REAR 2=UPPER...
  • Page 68 1=STANDARD ADJECTIVE 2=STANDARD NOUN 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN as a descriptor for the location of the control module currently being programmed. Noun/Adjective Screen ********************** 1=BASEMENT 2=BOILER@RM 3=CLASSROOM Noun Screen #1 ********************** 1=CLOSET 2=CORRIDOR 3=ELECTRIC@RM Noun Screen #2 ********************** 1=ELEVATOR 2=ENTRANCE 3=FLOOR Noun Screen #3 **********************...
  • Page 69 EDIT CONTROL 1=ADJECTIVE/NOUN 2=DESCRIPTION Edit Control Screen #4 • If the zero key is pressed, a 0 is placed in the first letter position • If the zero key is then pressed a second time with no intervening key actions, the entire Adjective field is replaced with the field entered for the previous device programmed, and the cursor moves to the last character of the field (Recall function).

  • Page 70: 2=Zone Setup

    3.6.2 Zone Setup PROGRAMMING 1=POINT Pressing 2 while viewing Programming Screen #2 will access the Zone Setup screens as 2=ZONE SETUP illustrated below: 3=LOOP SETUP Programming Screen #2 3.6.2.1 Enable ZONE SETUP 1=ENABLE Pressing 1 for Enable, while viewing Zone Setup Screen #1, will display the following 2=DISABLE screen: 3=ZONE 97 98 99...

  • Page 71: Disable

    3.6.2.2 Disable ZONE SETUP Pressing 2 for Disable, while viewing Zone Setup Screen #1, will display the 1=ENABLE following screen: 2=DISABLE 3=ZONE 97 98 99 Zone Setup Screen #1 3.6.2.3 Zone 97, 98 and 99 @@ZONE@TO@DISABLE Disable Screen @SPEC@PURPOSE@ZONE 1=PAS 97@@@@@@@@OFF 2=PRESIGNAL@98@@OFF 3=ZONE@99@@@@@@@OFF Zone 97, 98 and 99 Screen...

  • Page 72: Zones Installed

    3.6.2.4 Zones Installed ZONE SETUP Pressing 1 for Zones Installed, while viewing Zone Setup Screen #2, will display a 1=ZONES INSTALLED screen similar to the following: 2=ZONES ENABLED 3=ZONES DISABLED Zone Setup Screen #2 This display will show all of the zones that have been programmed into the control panel.

  • Page 73: Zone Type

    63) and assign it to the same zone as the waterflow type monitor module. All notification appliances connected to the control module will be nonsilenceable as will any other devices assigned to the same zone. Unimode 9600 PN 51336:C 11/06/01 @@ZONE@TYPE@PROG 1=Z00@@ALARM...

  • Page 74: 3=Loop Setup

    3.6.3 Loop Setup PROGRAMMING 1=POINT PROGRAM Loop Setup allows the programmer to configure the SLC Loop(s) for NFPA Style 4, 6 or 7 2=ZONE SETUP wiring and to select the protocol for each loop. Pressing 3 while viewing Programming 3=LOOP SETUP Screen #1 will cause the following screen to be displayed: Programming Screen #1 Press 1 while viewing the Loop Selection Screen to configure Loop1 or 2 to configure...

  • Page 75: 4: System Setup

    3.6.4 System Setup System Setup allows the programmer to configure the following control panel features: • Trouble Reminder: This feature, when enabled, provides an audible reminder that an alarm or trouble still exists on the FACP after the control panel has been silenced. The control panel piezo sounder will pulse once every 15 seconds during an alarm and every two minutes during a trouble condition, after the Alarm Silence or Acknowledge key is pressed.

  • Page 76: Banner

    3.6.4.2 Banner BANNER 1=FACTORY 2=USER DEFINED Banner Screen @@@@@@BANNER 1=FACTORY 2=USER@DEFINED Banner Screen @@@FACTORY@BANNER FIRE@LITE@ALARMS@INC Factory Banner Screen USER@DEFINED@BANNER PRESS@ENTER@IF@OK User Defined Banner Screen...

  • Page 77: Time-Date

    3.6.4.3 Time-Date SYSTEM SETUP 1=TROUBLE REM 2=BANNER 3=TIME-DATE System Setup Screen #1 3.6.4.3.1 Time @@@TIME@AND@DATE 1=TIME@@10:00@AM 2=DATE@@04-07-2000 3=CLOCK@FORMAT@@12HR Time-Date Screen #1 @@@TIME@AND@DATE 1=DAYLIGHT@SAVINGS Time-Date Screen #2 @@@@@ENTER@TIME 10:00@AM 1=AM@@@@@@@@@@@@2=PM Time Screen...

  • Page 78: Date

    3.6.4.3.2 Date 3.6.4.3.3 Clock Format 3.6.4.3.4 Daylight Savings Time TIME AND DATE 1=DAYLIGHT SAVINGS System Setup Screen #2 @@@@@ENTER@DATE MONTH@DAY@YEAR 04-07-2001 Date Screen @@DAYLIGHT@SAVINGS 1=ENABLED@@@@@@@@YES 2=START@MONTH@@@@APR 3=START@WEEK@@WEEK-1 Daylight Savings Screen #1 @@DAYLIGHT@SAVINGS 1=END@MONTH@@@@@@OCT 2=END@WEEK@@@@LAST-W Daylight Savings Screen #2...

  • Page 79: Timers

    3.6.4.4 Timers SYSTEM SETUP 1=TIMERS 2=NAC 3=RELAYS System Setup Screen #2 3.6.4.4.1 PAS (Positive Alarm Sequence) Delay TIMERS 1=PAS DELAY 2=PRE SIGNAL 3=WATERFLOW Timer Screen #1 @@@@@@TIMERS 1=PAS@DELAY@@@@@@000 2=PRE@SIGNAL@@@@@000 3=WATERFLOW@@@@@@000 Timer Screen #1 @@@@@@TIMERS 1=AC@LOSS@DELAY@@000 Timer Screen #2 @@@@@PAS@DELAY RANGE@0-180@SECONDS PAS Delay Screen...

  • Page 80: Presignal@Delay

    3.6.4.4.2 Pre-signal Delay 3.6.4.4.3 Waterflow Delay TIMER 1=PAS DELAY 2=PRE SIGNAL 3=WATERFLOW Timer Screen #1 @@PRESIGNAL@DELAY RANGE@0-180@SECONDS Pre-signal Delay Screen @@WATERFLOW@DELAY RANGE@0-90@SECONDS Waterflow Delay Screen...

  • Page 81: Ac Loss Delay

    3.6.4.4.4 AC Loss Delay TIMER 1=AC LOSS DELAY Timer Screen #2 3.6.4.5 NAC (Notification Appliance Circuit) SYSTEM SETUP 1=TIMERS 2=NAC 3=RELAYS System Setup Screen #2 @AC@LOSS@DELAY 1=NO@DELAY 2=ENTER@DELAY AC Loss Delay Screen #1 @AC@LOSS@DELAY RANGE@00-23 AC Loss Delay Screen #2 @@@@@@@NACS 1=NAC@1 2=NAC@2...

  • Page 82: Enabled

    @@@@@@@NAC@# 1=ENABLED@@@@@@@@YES 2=TYPE@@@@@@@@@@@BELL 3=SILENCEABLE@@@@YES NAC Screen #1 @@@@@@@NAC@# 1=AUTO@SILENCE@@@@00 2=CODING @@@@@@@@@@@@TEMPORAL NAC Screen #2 @@@@@@@NAC@# 1=ZONE @@@@00@00@00@00@00 2=SIL@INHIBITED@@@NO NAC Screen #3 @@@@@@@NAC@# 1=SYNC@TYPE@@@@@@@@S NAC Screen #4 3.6.4.5.1 Enabled...

  • Page 83: Type

    Silence key is pressed. The visual devices (strobes, etc.) will continue to operate. Unimode 9600 PN 51336:C 11/06/01 @@@@@@@NAC@TYPE 1=BELL...

  • Page 84: Auto Silence

    3.6.4.5.4 Auto Silence NAC # 1=AUTO SILENCE 2=CODING TEMPORAL NAC Screen #2 3.6.4.5.5 Coding @@AUTO@SILENCE 1=NO 2=5@MINUTES 3=10@MINUTES Auto Silence Screen #1 @@AUTO@SILENCE 1=15@MINUTES 2=20@MINUTES 3=25@MINUTES Auto Silence Screen #2 @@AUTO@SILENCE 1=30@MINUTES Auto Silence Screen #3 @@@@@CODING 1=STEADY 2=MARCH@TIME 3=CALIFORNIA Coding Screen #1 @@@@@CODING 1=TEMPORAL...

  • Page 85: Zone

    • Steady - a continuous output with no coding • March Time - 120 ppm (pulse-per-minute) output • California - 10 seconds on and 5 seconds off • Temporal - ½ second on, ½ second off, ½ second on, ½ second off, ½ second on, 1½ second off •...

  • Page 86: Relays

    3.6.4.6 Relays SYSTEM SETUP 1=TIMERS 2=NAC 3=RELAYS System Setup Screen #2 @@@@@RELAY 1=ALARM 2=SUPERVISORY 3=SUPERVISORY@AR Relay Screen #1 @@@@@RELAY 1=TROUBLE 2=COMM FAIL 3=PROCESS@MON Relay Screen #2 @@@@@RELAYS 1=RELAY@1 2=RELAY@2 3=RELAY@3 Relays Selection Screen @@@@@RELAY@# 1=TYPE @@@@@@@@@@@@@@ALARM Relay Type Screen @@@@@RELAY 1=PROCMON@AR 2=AC@LOSS 3=HAZARD...

  • Page 87: 5: Autoprogram

    3.6.5 Autoprogram PROGRAMMING Pressing 2 while viewing Programming Screen #2, will select the Autoprogram option, 1=SYSTEM SETUP which prompts the control panel to poll all devices installed on one or both SLC loops. 2=AUTOPROGRAM The primary purpose of autoprogramming is to allow the installer a fast and easy way to 3=VERIFY LOOPS bring the system on-line as quickly as possible.

  • Page 88: 6: Verify Loops

    3.6.6 Verify Loops PROGRAMMING Pressing 3 while viewing Programming Screen #2, will select the Verify Loops option and 1=SYSTEM SETUP display the following screen: 2=AUTOPROGRAM 3=VERIFY LOOPS Programming Screen #2 During loop verification, the FACP polls each device on the selected SLC to determine if the device is communicating and whether or not it responds with the proper type identification.

  • Page 89: View Events

    3.6.7.1 View Events HISTORY 1=VIEW EVENTS 2=ERASE HISTORY History Screen 3.6.7.2 Erase History @@@@@@HISTORY 1=VIEW@ALL 2=VIEW@ALARMS 3=VIEW@OTHER@EVENTS View Events Screen @@@ERASE@HISTORY @@@@@PROCEED@? 1=YES@@@@@@@@@@@2=NO Erase History Screen @@@ERASING@HISTORY @@@@@PLEASE@WAIT Erase History Wait Screen...

  • Page 90: 8: Walktest

    3.6.8 Walktest PROGRAMMING Walktest allows an individual to test the fire alarm system without the necessity to reset 1=HISTORY the control panel after each device activation. Pressing 2 while viewing the Programming 2=WALKTEST Screen #3 will cause the following Walktest options to be displayed: 3=OPTION MODULES Programming Screen #3 To perform a silent walktest which will not sound the NACs, press 1 while viewing the...

  • Page 91: 9: Option Modules

    3.6.9 Option Modules PROGRAMMING Options available for the Unimode 9600 include ADT-ACS Series, Graphic and LCD 1=HISTORY annunciators, ADT-UDACT Digital Alarm Communicator/Transmitter (with software 2=WALKTEST #UDACT02.0 and above), printer connection for acquiring hardcopy printouts of panel 3=OPTION MODULES data and PC (Personal Computer) connection for uploading and downloading panel data.

  • Page 92: Printer/Pc

    3.6.9.2 Printer/PC OPTION MODULES 1=ANNUNCIATORS/UDACT 2=ON BOARD DACT 3=PRINTER/PC Option Module Screen @@@@ANNUNCIATOR 1=ADDRESS@1@@@@@@@YES 2=ADDRESS@2@@@@@@@@NO 3=ADDRESS@3@@@@@@@@NO ACS Installed Screen @@@@@PRINTER-PC 1=PRINTER@NO@SU@@@NO 2=PRINTER@SU@@@@@YES 3=PC@@@@@@@@@@@@@@NO Printer-PC Screen @PRINTER@BAUD@RATE 1=2400@BAUD 2=4800@BAUD 3=9600@BAUD Printer Baud Rate Screen...

  • Page 93: 10: Password Change

    3.6.10 Password Change PROGRAMMING The factory set passwords, which have been programmed into the control panel, can be 1=PASSWORD CHANGE changed by selecting the Password Change option. Pressing 1 while viewing 2=CLEAR PROGRAM Programming Screen #4 will cause the following screen to be displayed: 3=LOAD PROGRAM Programming Screen #4 Press 1 to change the Master Programming Level password or 2 to change the...

  • Page 94: 11: Clear Program

    3.6.11 Clear Program PROGRAMMING Pressing 2 while viewing Programming Screen #4, will select the Clear Program option. 1=PASSWORD CHANGE This will cause the LCD to display the following screens: 2=CLEAR PROGRAM 3=LOAD PROGRAM Programming Screen #4 Pressing 1, for Whole System while viewing the Clear Program Screen #1, will clear all general system programming options and all programmed addressable devices from the nonvolatile memory of the FACP.

  • Page 95: 12: Program Check

    3.6.12 Program Check PROGRAMMING The Program Check feature allows the programmer to view the zones which have been 1=PASSWORD CHANGE programmed to the Notification Appliance Circuits on the control panel but have not been 2=CLEAR PROGRAM programmed to Initiating Devices as well as other circuits with no input or output 3=LOAD PROGRAM correlations.
  • Page 96 Pressing 2 while viewing the Program Check screen will display a screen similar to the following: @@@ZONES@NO@INPUT 05@07@09@10@11@1M001 The Zone No Input screen allows the programmer to view the zones which have not been programmed to at least one input device (not including general alarm Zone 00). The example in the preceding screen indicates that Zones 05, 07, 09, 10 and 11 have been programmed to an addressable module (control module in this example) with an address of 001 on loop 1 but have not been programmed to any input devices.

  • Page 97: Maintenance Programming Level

    3.7 Maintenance Programming Level To access Maintenance Programming mode, press the Enter key. The LCD will display the following: To enter the Maintenance Programming mode, press 2. The display will read as follows: When the Maintenance level password (default 11111) is entered, the following screen will appear: Note that in the preceding screens, an arrow appears to inform the programmer that additional options can be viewed by pressing the keypad down arrow key, as shown in the...

  • Page 98: 1: Disable Point

    3.7.1 Disable Point PROGRAMMING Pressing 1 for Point Program, while viewing Maintenance Screen #1 will cause the 1=POINT PROGRAM following screens to be displayed: 2=HISTORY 3=PROGRAM CHECK Maintenance Screen #1 Select the Loop, containing the device to be disabled, by pressing 1 for Loop 1 or 2 for Loop 2.

  • Page 99: 2=History

    3.7.2 History PROGRAMMING Pressing 2 while viewing Maintenance Screen #1 will cause the following screen to be 1=POINT PROGRAM displayed: 2=HISTORY 3=PROGRAM CHECK Maintenance Screen #1 The History feature allows the operator to view control panel events which have been stored in a history file in memory and erase the contents of the history file Pressing 1 while viewing the History screen will cause the following screen to be displayed:...

  • Page 100: 3=Program Check

    3.7.3 Program Check PROGRAMMING Pressing 3 while viewing Maintenance Screen #1 will cause the following screen to be 1=POINT PROGRAM displayed: 2=HISTORY 3=PROGRAM CHECK Maintenance Screen #1 The Program Check feature allows the programmer to view the zones which have been programmed to the Notification Appliance Circuits on the control panel but have not been programmed to Initiating Devices as well as other circuits with no input or output correlations.

  • Page 101: 4: Walktest

    Pressing 3 while viewing Program Check screen will cause a screen similar to the following to be displayed: The Zone No Output feature allows the programmer to view the zones which have not been programmed to at least one output device (not including general alarm Zone 00). The example in the preceding screen indicates that Zones 05, 07, 09, 10 and 11 have been programmed to an addressable detector with an address of 001 on loop 1 but have not been programmed to any output devices.
  • Page 102 Pressing 1 while viewing the System Screen will cause the following screen to be displayed: @@@TIME@AND@DATE 1=TIME @01:00@AM 2=DATE@@01-01-2001 @@@@@@@@@@@@@@@12HR Time and Date Screen To change the time, press 1 to display the following screen: @@@@@ENTER@TIME 01:00@AM 1=AM@@@@@@@@@@@@2=PM Time Screen A flashing cursor will appear on the left side of the display.

  • Page 103: 6: Zone Setup

    3.7.6 Zone Setup PROGRAMMING Pressing 3 while viewing Maintenance Screen #2 will display the following screen: 1=WALKTEST 2=SYSTEM 3=ZONE SETUP Maintenance Screen #2 Pressing 1 while viewing Zone Setup screen will display the following screen: A flashing cursor appears to the right of the Z. To enable a zone, enter the two digit zone number (00 - 99).
  • Page 104 Pressing 3 while viewing Zone Setup screen will display the following screen: SPEC PURPOSE ZONE 1=PAS 97 2=PRE-SIGNAL 98 3=FUTURE 99 Disable Screen...

  • Page 105: Section 4: Operating Instructions

    Operating Instructions SECTION 4 4.1 Panel Control Buttons 4.1.1 Acknowledge/Step The first press of the Acknowledge/Step key silences the piezo sounder, changes flashing LEDs to steady and also changes the status field on the LCD display from capital letters to small letters.

  • Page 106: Led Indicators

    4.2 LED Indicators The nine LED indicators, which are located on the front panel, operate as follows: AC Power This is a green LED which illuminates if AC power is applied to the FACP. A loss of AC power will turn off this LED Fire Alarm This red LED flashes when one or more alarms occur.

  • Page 107: Normal Operation

    To set the time and date, refer to the appropriate section in this manual. The Unimode 9600 performs the following functions at regular intervals while in Normal mode: ✓ Monitors AC input voltage and battery voltage ✓...
  • Page 108 Addressable Smoke Detectors, Monitor Modules and Control Modules For addressable devices connected to the SLC loop, the following is a typical message that could appear on the LCD display for a device trouble: TROUBL SMOKE (PHOTO) <ADJ> <NOUN> 10:00A 010801 1D001 The information displayed in the above example provides the following information: •...

  • Page 109: Alarm Operation

    Pressing the Acknowledge/Step or Alarm Silence key will cause the pulsing piezo to silence and the system Trouble LED to change from flashing to on steady. This block acknowledgment occurs regardless of the number of troubles, alarms and supervisory events active in the system. When the Acknowledge/Step key is pressed and at least one new alarm or trouble exists in the system, the ‘acknowledge’...

  • Page 110: Supervisory Operation

    • Second line in display: ✓ <ADJ>; refers to the user programmed adjective descriptor from library list resident in the control panel or custom entry via PC. ✓ <NOUN>; refers to the user programmed noun descriptor from library list resident in the control panel or custom entry via PC. •...

  • Page 111: Process Monitor Operation

    4.10 NAC Operation There are two programmable NACs (Notification Appliance Circuits) resident on the Unimode 9600 main circuit board. Both NACs may be programmed as silenceable or nonsilenceable and may also be programmed for steady or coded operation. Coded operation provides a choice between March Time, Temporal or California coding.

  • Page 112: Programmed Zone Operation

    4.15 Time Functions: Real-Time Clock The Unimode 9600 includes a crystal-based clock that provides time of day, date and day of week. Time is displayed as 12 or 24 hour time with month/day/year and is stored in RAM.

  • Page 113: Synchronized Nac Operation

    4.16 Synchronized NAC Operation Synchronization is a panel feature that controls the activation of notification appliances in such a way that all devices will turn on and off at exactly the same time. This is particularly critical when activating strobes which must be synchronized to avoid random activation and a potential hazard or confusion.

  • Page 114: Positive Alarm Sequence

    4.19 Positive Alarm Sequence PAS (Positive Alarm Sequence) option will program an initiating device to delay panel activation (including alarm relay and communicator) for a period of 15 seconds. Zone 97, however, will activate immediately and may be used to connect a signaling device to indicate PAS activation.

  • Page 115: Special System Timers

    4.20 Special System Timers 4.20.1 Silence Inhibit Timer This option, if selected, prevents the Alarm Silence key from functioning for 60 seconds following an alarm. A new alarm during the initial 60 seconds will cause the timer to restart with a new 60 seconds. Silence Inhibit operation requires the approval of the local Authority Having Jurisdiction.

  • Page 116: 5: Alarm Verification (None Or Two Minutes)

    4.20.5 Alarm Verification (None or Two Minutes) If alarm verification is selected, an addressable smoke detector's alarm is ignored for a retard time of 13 seconds and the detector's alarm condition is automatically reset. There will be no alarm indication at the FACP during the Retard period. A confirmation period of one minute and 47 seconds follows, during which a subsequent alarm from the same detector will cause the panel to immediately activate the appropriate outputs and indicate the alarm condition at the FACP.

  • Page 117: Read Status

    4.22 Read Status Read Status functions do not require a password. The control panel will continue to provide fire protection while in Read Status mode. This mode can be entered while the control panel is in alarm or trouble. If a new alarm or trouble occurs during these functions, the Read Status is exited to prevent confusion.

  • Page 118: 1: System Point

    4.22.1 System Point READ STATUS Pressing 1 while viewing Read Status Screen #1 will cause the following screen to be 1=SYSTEM POINT displayed: 2=ZONES 3=POWER Read Status Screen #1 The operator selects the loop containing the device to be read by pressing 1 for Loop 1 or 2 for Loop 2.

  • Page 119: 2=Zones

    Pressing the down arrow key, while viewing the screen shown above, will allow the operator to view additional programming information about the selected device, such as: • Enable/Disable Status • Device Type • Alarm Verification On/Off • Walktest Yes/No • PAS (Positive Alarm Sequence) Yes/No •...

  • Page 120: 4: Trouble Reminder

    4.22.3 Power Pressing 3 while viewing Read Status Screen #1 will cause the following screens to be displayed: A real-time display of the control panel voltages can be used to determine if a problem exists in the system. The following table lists the circuit being measured, possible conditions and their respective voltage ranges: Circuit Battery...

  • Page 121: 5: Timers

    4.22.5 Timers Pressing 2 while viewing Read Status Screen #2 will cause the following Timer screens to be displayed: TIMERS PAS DELAY PRE SIGNAL WATERFLOW TIMERS AC LOSS DELAY These screens will indicate the delay time, in seconds, for each of four possible delay options.

  • Page 122: 7: Relays

    4.22.7 Relays READ STATUS Pressing 1 while viewing Read Status Screen #3 will display the following screen: 1=RELAYS 2=PROGRAM CHECK 3=HISTORY Read Status Screen #3 The operator can view the programmed option for each relay by pressing the corresponding number key. 4.22.8 Program Check Pressing 2 while viewing Read Status Screen #3 will cause a screen similar to the following to be displayed:...

  • Page 123: 10: Annunciators

    4.22.10 Annunciators READ STATUS Pressing 1 while viewing Read Status Screen #4 will display the following screens: 1=ANNUNCIATORS 2=FUTURE USE 3=FUTURE USE Read Status Screen #4 Annunciator Screen #1 indicates if Terminal Mode, ACS Mode and UDACT options are enabled or disabled. Pressing ‘1’ while viewing Annunciator Screen #2 allows the operator to view the ACS Mode Annunciator addresses which have been programmed into the control panel.

  • Page 124: 12: Print

    4.22.12 Print To print program data or control panel status, press 3 while viewing Read Status Screen #5. The following screens will be displayed: Pressing 1 while viewing Print Screen #1 allows the user to print the History file which will detail all of the system activities since the file was last cleared from memory.
  • Page 125 Drift Compensation Drift compensation uses software algorithms that identify and compensate for long-term changes in the data readings from each addressable smoke detector. These long-term changes in detector data readings are typically caused by dirt and dust accumulation inside the smoke chamber. Drift compensation performs the following functions: •...

  • Page 126: 13: Time-Date

    4.22.13 Time-Date READ STATUS The operator can view the daylight savings time and the month and week when daylight 1=TIME-DATE savings time will begin and end. Pressing 1 while viewing Read Status Screen #6 will display the following screens: Read Status Screen #6 DAYLIGHT SAVINGS ENABLED START MONTH...

  • Page 127: Section 5: Power Supply Calculations

    Use Table 5.1 , to determine the total amount of current, in AC amperes (A), that must be supplied to the system. Device Type Unimode 9600 ADT-CHG-120 Unimode 9600 PN 51336:C 11/06/01 Table 5.1 120 VAC Branch Circuit Requirements Number of Current Draw Devices...

  • Page 128: Calculating The System Current Draw

    5.3 Calculating the System Current Draw 5.3.1 Overview 5.3.2 How to Use Table 5.3 on page 129 to Calculate System Current Draw Use Table 5.3 on page 129 to calculate current draws as follows: 1. Enter the quantity of devices in all three columns 2.
  • Page 129 Table 5.3 contains columns for calculating current draws. For each column, calculate the current and enter the total (in amperes) in the bottom row. When finished, copy the totals from Calculation Column 2 and Calculation Column 3 to Table 5.4 on page 130. Table 5.3 System Current Draw Calculations &DOFXODWLRQ &ROXPQ  3ULPDU\ 1RQ)LUH $ODUP &XUUHQW...

  • Page 130: Selecting And Locating Batteries

    5.4 Calculating the Battery Size Use Table 5.4 to calculate the total Standby and Alarm load in ampere hours (AH). This total load determines the battery size (in AH), required to support the control panel under the loss of AC power. Complete Table 5.4 as follows: 1.

  • Page 131: A.1: Correlations

    ✓ MMF-302 control module with address 04 ✓ CMF-300 control modules with addresses 09, 11 and 12 The example points out some of the key assignment features of the Unimode 9600. Addresses of detectors are not duplicated. Addresses of monitor and control modules are not duplicated.
  • Page 132 Correlation of Input and Output Zones Input Devices SD350 SD350 MMF-300 MMF-302 MMF-302 CP350 CP300 SD350 SD350 SD350 MMF-302 The zone correlations which are shown graphically above are also presented in Table A.1 on page 133 and Table A.2 on page 134. Zones Output Devices CMF-300...
  • Page 133 DETECTOR ZONE ASSIGNMENT Address Device Zone Type Number SD350 SD350 CP350 CP350 SD350 SD350 SD350 ADJ/NOUN Address Device Type FIRST HALL ELEV. LOBBY 2ND FLOOR ROOM 210 3RD FLOOR MEZZANINE MECH. ROOM Zone ADJ/NOUN Number...
  • Page 134 MONITOR/CONTROL MODULE ZONE ASSIGNMENT Address Device Zone Type Number MMF-300 MMF-302 1, 2 MMF-302 1, 2 MMF-302 CMF-300 CMF-300 CMF-300 CMF-300 CMF-300 1, 2, 3 CMF-300 CMF-300 CMF-300 CMF-300 ADJ/ Address Device NOUN Type Zone ADJ/NOUN Number...
  • Page 135 DETECTOR ZONE ASSIGNMENT Address Device Zone Type Number ADJ/ Address Device NOUN Type Zone ADJ/NOUN Number...
  • Page 136 DETECTOR ZONE ASSIGNMENT Address Device Zone Type Number ADJ/ Address Device NOUN Type Zone ADJ/NOUN Number...
  • Page 137 MONITOR/CONTROL MODULE ZONE ASSIGNMENT Address Device Zone Type Number ADJ/ Address Device NOUN Type Zone ADJ/NOUN Number...
  • Page 138 MONITOR/CONTROL MODULE ZONE ASSIGNMENT Address Device Zone Type Number ADJ/ Address Device NOUN Type Zone ADJ/NOUN Number...
  • Page 139 APPENDIX B The following table provides a list of the programming options and their factory default settings. Program Option Factory Default Detector Programming Not Installed Detector Type Smoke-Photo Detector Verification Detector Walktest Detector PAS Detector Presignal Detector Zone Assign. 000 only Detector Adj/Noun none Module Programming...
  • Page 140 It is important to use the correct type of wire, wire gauge and wire run length for each Unimode 9600 circuit. Reference the chart below to specify wire requirements and limitations for each Unimode 9600 circuit.
  • Page 141 ADT-AFM-16AT Annunciator 22 ADT-AFM-32A Annunciator 22 ADT-BG-10LX see also manual pull station 20 ADT-BG-12LX Unimode 9600 PN 51336:C 09/19/01 see also manual pull station 19 ADT-CHG-120 see also battery charger 22 see also remote battery charger ADT-LCD-80F annunciator 13, 23...
  • Page 142 24 municipal box transmitter see also 4XTMF module 31 NAC 14, 17, 81, 111 Auto Silence 84 coded 113 coding 84 current 14 End-of-Line Resistor 14 power 12 see also Notification Appliance Unimode 9600 PN 51336:C 09/19/01...
  • Page 143 PAS 48, 71, 114 see also Positive Alarm Se- quence 12, 47 selection 59 PAS BYPASS 114 PAS timer 79 Unimode 9600 PN 51336:C 09/19/01 Password 13, 40 change 93 Maintenance Level 2 41, 97 password Master Level 1 41...
  • Page 144 Maintenance Level 103 zone type 73 list 73 Zone Z97 48 Zone Z98 pre-signal zone 48 Zones 119, 131 see also software zones 12 Zones Disabled 72 Zones Enabled 72 Zones Installed 72 zones per device 49 Unimode 9600 PN 51336:C 09/19/01...
  • Page 145 Notes...
  • Page 146 Notes...
  • Page 147 Notes...

Table of Contents

Save PDF