Johnson Controls YORK OPTIVIEW CONTROL CENTER Operation Manual page 124

SECTION 4 - PRINTERS
[Skip the following section if Liquid Level is not enabled]
Refrigerant Level Control
-----------------------------------------------------
Refrigerant Level Position
Purge Control
-----------------------------------------------------
Pressure
Exhaust Count
Exhaust Window
[Skip the following section if Motor Type is not EM]
Electro-Mechanical Starter
-----------------------------------------------------
Motor Run
% Full Load Amps
[Skip the following section if Motor Type is not Mod B SSS]
Liquid-Cooled Solid State Starter
-----------------------------------------------------
Starter Model
Motor Run
% Full Load Amps
kW Hours
Input Power
Phase A Voltage
Phase B Voltage
Phase C Voltage
Phase A Current
Phase B Current
Phase C Current
Phase A Temperature
Phase B Temperature
Phase C Temperature
[Skip the following section if Motor Type is not VSD]
Variable Speed Drive
-----------------------------------------------------
Motor Run
% Full Load Amps
Pre-Rotation Vanes Position
Full Load Amps
Precharge Relay Output
Trigger SCR Output
Water Pump Output
kW Hours
Input Power
Output Frequency
Output Voltage
DC Bus Voltage
DC Inverter Link Current
Phase A Output Current
Phase B Output Current
Phase C Output Current
Internal Ambient Temperature
Converter Heatsink Temperature
Phase A Heatsink Temperature [If TMIII VSD]
Phase B Heatsink Temperature [If TMIII VSD]
Phase C Heatsink Temperature [If TMIII VSD]
Baseplate Temperature [If VyperDrive VSD] = 106 ºF
FIGURE 44 - SAMPLE PRINTOUT (STATUS) (CONT'D)
124
[Skip the following section if Motor Type is not VSD or Filter is
not present]
Harmonic Filter Data
----------------------------------------------------
= 35 %
Precharge Contactor
Supply Contactor
Operating Mode
Phase Rotation
= 30.1 PSIA
Total Supply kVA
= 0
Total Power Factor
= 0 Min
DC Bus Voltage
Heatsink Temperature [If TMIII VSD]
Baseplate Temperature [If VyperDrive VSD] = 102 ºF
Voltage Peak N-L1
Voltage Peak N-L2
= On
Voltage Peak N-L3
= 94 %
L1-L2 RMS Voltage
L2-L3 RMS Voltage
L3-L1 RMS Voltage
L1 RMS Filter Current
L2 RMS Filter Current
= 26L
L3 RMS Filter Current
= On
L1 RMS Supply Current
= 95 %
L2 RMS Supply Current
= 20723 kWH
L3 RMS Supply Current
= 8225 kW
L1 Voltage Total Harmonic Distortion
= 422 V
L2 Voltage Total Harmonic Distortion
= 449 V
L3 Voltage Total Harmonic Distortion
= 449 V
L1 Supply Current Total Demand Distortion = 2.6 %
= 253 A
L2 Supply Current Total Demand Distortion = 2.3 %
= 257 A
L3 Supply Current Total Demand Distortion = 2.8 %
= 262 A
= 109 ºF
= 109 ºF
= 110 ºF
FIGURE 44 - SAMPLE PRINTOUT (STATUS) (CONT'D)
Motor Winding Temperature
= On
-----------------------------------------------------
= 94 %
A1
= 75 %
B1
= 402 A
B2
= Off
= On
Bearing Temperature
= On
-----------------------------------------------------
= 14528 kWH
Sensor 1
= 150 kW
Sensor 2
= 60 Hz
= 800 V
= 600 V
= 300 A
= 195 A FIGURE 44 - SAMPLE PRINTOUT (STATUS) (CONT'D)
= 198 A
= 193 A
= 88 ºF
= 102 ºF
= 93 ºF
= 99 ºF
= 97 ºF
FORM 160.10-O1
ISSUE DATE: 4/27/2018
= Off
= On
= Running
= ABC
= 148 kVA
= 0.97
= 608 V
= 102 ºF
= 200 V
= 200 V
= 200 V
= 215 V
= 215 V
= 215 V
= 150 A
= 150 A
= 150 A
= 152 A
= 152 A
= 152 A
= 1.5 %
= 1.2 %
= 1.1 %
= 193.3 ºF
= 192.5 ºF
= 193.1 ºF
= 128.3 ºF
= 129.5 ºF
JOHNSON CONTROLS