Disabled Persons Access Settings - CDVI DIGIWAY Plus Manual

EN
Advanced Setting
25) 25)
Test FTC-S Fail
In case of malfunction of the safety photocells FTC-S, it's possible to set the operating mode: In case of malfunction of the safety photocells FTC-S, it's possible to set the operating mode:
STOP / LOW ENERGY motion STOP / LOW ENERGY motion
Advanced Setting
26) 26)
Low Energy
The sw calculates the minimum opening/closing time when the malfunction mode is set at Low The sw calculates the minimum opening/closing time when the malfunction mode is set at Low
Energy, according to the doorset diameter (in m) and weight (in Kg). Energy, according to the doorset diameter (in m) and weight (in Kg).
Advanced Setting
27) 27)
Low Energy
Sets the doorset weight in Kg. Sets the doorset weight in Kg.

Disabled persons access settings

Disabled persons access settings
If the operator is used for disabled persons access, adjust the opening and closing If the operator is used for disabled persons access, adjust the opening and closing
speed of the leaf for Low Energy setting. speed of the leaf for Low Energy setting.
NOTE1: NOTE1:
According to the Regulation, when activated the DISABLED PERSONS ACCESS [See According to the Regulation, when activated the DISABLED PERSONS ACCESS [See
configuration Menu]: configuration Menu]:
• • The min. Pause Time must be set at 5 Sec. The min. Pause Time must be set at 5 Sec.
• • The motor torque measured at the main closing edge must be lower then 67 N. The motor torque measured at the main closing edge must be lower then 67 N.
• • The min slow time time in closing must be 1,5 sec. The min slow time time in closing must be 1,5 sec.
These values can be set in the Main Functions menu. These values can be set in the Main Functions menu.
NOTE2: NOTE2:
When the Disabled Persons Mode is enabled, if the door is open through a C-NO command When the Disabled Persons Mode is enabled, if the door is open through a C-NO command
on inputs 15-16, it will reclose after the Pause Time on inputs 15-16, it will reclose after the Pause Time Extended. If the command comes
from inputs (radar, push&go, remote control), the Pause time remains the regular one. from inputs (radar, push&go, remote control), the Pause time remains the regular one.
The Pause Time extended is The Pause Time extended is always
button D of a remote control. button D of a remote control.
Warning: Disabled person access doors must be Warning: Disabled person access doors must be
identified with proper signage. identified with proper signage.
Inward or Outward Door Operator
STOP /
LOW ENERGY
Diameter (m)
1,2
|||||||||||||||||......................
Weight ( Kg )
120
|||||||||||||||||...................
Door lenght Door lenght
50 Kg 50 Kg
750 mm 750 mm 3,0 s 3,0 s
850 mm 850 mm 3,1 s 3,1 s
1000 mm 1000 mm 3,2 s 3,2 s
1200 mm 1200 mm 3,8 s 3,8 s
always executed if the open command comes from the executed if the open command comes from the
DIGIWAY Plus
Door weight Door weight
60 Kg 60 Kg 70 Kg 70 Kg 80 Kg 80 Kg
3,1 s 3,1 s 3,2 s 3,2 s 3,3 s 3,3 s
3,1 s 3,1 s 3,2 s 3,2 s 3,4 s 3,4 s
3,4 s 3,4 s 3,7 s 3,7 s 4,0 s 4,0 s
4,2 s 4,2 s 4,5 s 4,5 s 4,8 s 4,8 s
Extended. If the command comes
90 Kg 90 Kg
3,5 s 3,5 s
3,6 s 3,6 s
4,2 s 4,2 s
5,1 s 5,1 s
29