CDVI DIGIWAY Plus Manual page 26

Advanced Setting
5) 5)
Wind Stop Torque
It is possible to adjust the torque of the motor when the wind stop function is enabled. This allows It is possible to adjust the torque of the motor when the wind stop function is enabled. This allows
you to change the value of the force applied by the door relative to the wind pressure. you to change the value of the force applied by the door relative to the wind pressure.
Press the UP or DOWN buttons to increase or decrease the torque and confirm with OK. Press the UP or DOWN buttons to increase or decrease the torque and confirm with OK.
Default value = 50%. Default value =
Advanced Setting
6) 6)
Dynamic Pause
Dynamic pause is a function which automatically adjusts the programmed pause time, preventing Dynamic pause is a function which automatically adjusts the programmed pause time, preventing
too many close attempts of the door in high traffific situations. When enabled, this function increases too many close attempts of the door in high traffific situations. When enabled, this function increases
the programmed pause time by 1 sec. each time it detects a passage through the door during the the programmed pause time by 1 sec. each time it detects a passage through the door during the
closing phase, and restarts the time when passage is detected when the door is open. closing phase, and restarts the time when passage is detected when the door is open.
Once the door completes its cycle up to the closed status, the pause time is reset to the programmed Once the door completes its cycle up to the closed status, the pause time is reset to the programmed
value. value.
Press UP or DOWN buttons to enable or disable the function and confirm with OK. Press UP or DOWN buttons to enable or disable the function and confirm with OK.
Default value = DISABLE. Default value = DISABLE.
Advanced Setting
7) 7)
FTC-S Exclusion
wall wall
WARNING: the excluded zone may become a health & safety hazard because it WARNING: the excluded zone may become a health & safety hazard because it
not protected! not protected!
Advanced Setting
8) 8)
Ex Power Open
When enabled, this adds one more OPENING When enabled, this adds one more
possible friction or door imbalance. possible friction or door imbalance.
Enable or disable this function with the UP or DOWN buttons and confirm with OK. Enable or disable this function with the UP or DOWN buttons and confirm with OK.
Default value = DISABLE Default value = DISABLE
Advanced Setting
9) 9)
Ex Open Torque
This function allows to set the This function allows to set the TORQUE
Change the value by pressing the UP or DOWN buttons and confirm with OK. Change the value by pressing the UP or DOWN buttons and confirm with OK.
Default value = 50% Default value = 50%
Advanced Setting
10) 10)
Extra Open Time
This function allows to set the duration This function allows to set the duration TIME
Change the value by pressing the UP or DOWN buttons and confirm with OK. Change the value by pressing the UP or DOWN buttons and confirm with OK.
Default value = 0 SEC Default value = 0 SEC
26
DIGIWAY Plus
Inward or Outward Door Operator
Wind Stop Torque
|||||||||||||||||............10%
50%.
Enable / Disable
FTC-S Exclusion
000
|||||||||||||||||.................
If the door is next to a wall and is using a curtain protection device, If the door is next to a wall and is using a curtain protection device,
it may be necessary to prevent the device being activated by the it may be necessary to prevent the device being activated by the
FTC-S active zone FTC-S active zone
wall to allow a complete opening of the leaf. wall to allow a complete opening of the leaf.
door door
Set the zone width as percentage of the full door motion using the Set the zone width as percentage of the full door motion using the
UP or DOWN buttons to increase or decrease the value. UP or DOWN buttons to increase or decrease the value.
000 = Door OPEN 000 = Door OPEN
100 = Door CLOSED 100 = Door CLOSED
Example: if you want to disable the curtain device when the leaf is Example: if you want to disable the curtain device when the leaf is
open at the 80% of the complete travel, set the value to 20. open at the 80% of the complete travel, set the value to 20.
Enable / Disable
OPENING pulse at the end of the opening cycle to compensate
Ex Open Torque
|||||||||||||||||..................
TORQUE of the
Extra Open Time
0 SEC.
|||||||||||||||||...............
pulse at the end of the opening cycle to compensate
50 %
of the OPENING OPENING extra pulse extra pulse. .
TIME of the of the OPENING OPENING extra pulse extra pulse
EN