CDVI DIGIWAY Plus Manual page 27

EN
Advanced Setting
11) 11)
Ex Power Close
When enabled, adds one more CLOSING When enabled, adds one more
possible friction or door imbalance. possible friction or door imbalance.
Enable or disable this function with the UP or DOWN buttons and confirm with OK Enable or disable this function with the UP or DOWN buttons and confirm with OK
Default value = DISABLE Default value = DISABLE
Advanced Setting
12) 12)
Ex Close Torque
This function allows to set the TORQUE This function allows to set the
Change the value by pressing the UP or DOWN buttons and confirm with OK. Change the value by pressing the UP or DOWN buttons and confirm with OK.
Default value = 50% Default value = 50%
Advanced Setting
13) 13)
Extra Close Time
This function allows to set the duration This function allows to set the duration TIME
Change the value by pressing the UP or DOWN buttons and confirm with OK. Change the value by pressing the UP or DOWN buttons and confirm with OK.
Default value = 0 SEC Default value = 0 SEC
Advanced Setting
14) 14)
Fire Release
When the Fire Release function is enabled, it's possible to set the reaction of the door depending on When the Fire Release function is enabled, it's possible to set the reaction of the door depending on
the failure of the Fire power (V+, V-): the failure of the Fire power (V+, V-):
• • DOOR FREE = In case of DOOR FREE = In case of Fire Power
• • DOOR OPEN DOOR OPEN = In case of
is reset or the function of the Menu Configuration is disabled. is reset or the function of the
• • DOOR CLOSED LOCKED = Door CLOSED and lock active DOOR CLOSED LOCKED
• • DOOR CLOSED UNLOCKED = = Door CLOSED and lock disactive DOOR CLOSED UNLOCKED
Advanced Setting
15) 15)
Max Obst Cycles
When the door meets an obstacle during closing, it re-opens immediately. At the end of the pause When the door meets an obstacle during closing, it re-opens immediately. At the end of the pause
time, it re-closes. If the obstacle is still present the cycle restarts. time, it re-closes. If the obstacle is still present the cycle restarts.
This parameter sets the max number of re-closing attempts before stop and wait for an external This parameter sets the max number of re-closing attempts before stop and wait for an external
command. Range : from command. Range : from 1 to 256
Default value = 100 attempts Default value = 100 attempts
Advanced Setting
16) 16)
OD on Closing
After the detection of an obstacle during the closing the door will react in different way, according to After the detection of an obstacle during the closing the door will react in different way, according to
the following settings: the following settings:
• • Reopen: The door reopens and after the pause time recloses Reopen: The door reopens and after the pause time recloses
• • Stop & Wait: The door stops and after the pause time recloses Stop & Wait: The door stops and after the pause time recloses
• • STOP: The door stops and waits for a command to reopen and for a further command STOP: The door stops and waits for a command to reopen and for a further command
to reclose. to reclose.
Inward or Outward Door Operator
Enable / Disable
CLOSING pulse after the regular CLOSING cycle to compensate
Ex Close Torque
50 %
|||||||||||||||||...................
TORQUE of the
Extra Close Time
|||||||||||||||||.........0 SEC.
Fire Release
Open/Free/Closed
Fire Power failure the door becomes FREE (System Off)
= In case of Fire Power Fire Power failure the door opens and stays OPEN until the fire power
Menu Configuration is disabled.
= Door CLOSED and lock active
Door CLOSED and lock disactive
Max Obst Cycles
|||||||||||||||||.............000
1 to 256 . . Value 0 of the parameter means no limit. Value 0 of the parameter means no limit.
OD on Closing
Reopen
DIGIWAY Plus
pulse after the regular CLOSING cycle to compensate
of the CLOSING CLOSING extra pulse extra pulse. .
TIME of the of the CLOSING CLOSING extra pulse. extra pulse.
failure the door becomes FREE (System Off)
failure the door opens and stays OPEN until the fire power
27