Set Data Flow Control Method - Lutron Electronics RadioTouch RTA-RS232 Setup And Installation Manual

Programming the RS232 Interface
Step 4

Set data flow control method

No flow control is the default for the RS232 Interface. If
you are using no flow control, you have completed the
Start-Up of the RS232 Interface. If you are using full
seven wire hardware handshaking or three wire
software flow control, continue with Step 4.
Step A:Enter unit configuration mode by pressing and
holding the mode and address buttons for 5
seconds. The LED display will begin flashing
UC when the unit has entered unit
configuration mode.
OR
See the RTA-RS232 Setup Guide for interface
Optional Terminal
programming and operation instructions. For
Block Connector
additional system details consult the
RadioTouch Installers Guide, which is
TM
1 2 3 included with each RadioTouch
RadioTouch is a trademark of Lutron Electronics Co., Inc.
This product may be covered by one or more of the following
U.S. patents: 5,248,919; 5,399,940; 5,736,965; 5,798,581;
5,838,226; 5,848,054; 5,905,442, 5,982,103
For additional assistance call the Lutron Technical
(800) 523-9466.
Support Center at
OR
See the RTA-RS232 Setup Guide for interface
Optional Terminal
programming and operation instructions. For
Block Connector
additional system details consult the
RadioTouch Installers Guide, which is
TM
1 2 3 included with each RadioTouch
RadioTouch is a trademark of Lutron Electronics Co., Inc.
This product may be covered by one or more of the following
U.S. patents: 5,248,919; 5,399,940; 5,736,965; 5,798,581;
5,838,226; 5,848,054; 5,905,442, 5,982,103
For additional assistance call the Lutron Technical
(800) 523-9466.
Support Center at
14 RadioTouch Setup Guide for RTA-RS232
TM
Controller.
TM
P/N 500-9258 Rev A
Controller.
TM
P/N 500-9258 Rev A
Step B:Once UC is flashing, press the mode button
repeatedly until the display shows HS.
OR
See the RTA-RS232 Setup Guide for interface
Optional Terminal
programming and operation instructions. For
Block Connector
additional system details consult the
RadioTouch Installers Guide, which is
TM
included with each RadioTouch
1 2 3
RadioTouch is a trademark of Lutron Electronics Co., Inc.
This product may be covered by one or more of the following
U.S. patents: 5,248,919; 5,399,940; 5,736,965; 5,798,581;
5,838,226; 5,848,054; 5,905,442, 5,982,103
For additional assistance call the Lutron Technical
(800) 523-9466.
Support Center at
Once the display shows HS press the enter
button and the current flow control setting will
be displayed on the right LED display.
OR
See the RTA-RS232 Setup Guide for interface
Optional Terminal
programming and operation instructions. For
Block Connector
additional system details consult the
RadioTouch Installers Guide, which is
TM
1 2 3 included with each RadioTouch
RadioTouch is a trademark of Lutron Electronics Co., Inc.
This product may be covered by one or more of the following
U.S. patents: 5,248,919; 5,399,940; 5,736,965; 5,798,581;
5,838,226; 5,848,054; 5,905,442, 5,982,103
For additional assistance call the Lutron Technical
(800) 523-9466.
Support Center at
Controller.
TM
P/N 500-9258 Rev A
Controller.
TM
P/N 500-9258 Rev A