Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Siruba ASP-EBJ100
Summary of Contents for Siruba ASP-EBJ100
- Page 1 ORIGINAL 使用說明書與零件圖 INSTRUCTIONS BOOK & PARTS LIST ASP-EBJ100...
- Page 3 ENGLISH...
- Page 4 GENERAL SAFETY INSTRUCTION For the sewing machine, automatic mechanic system, and auxiliary devices (hereinafter referred as “machine ＂ ), it is inevitable to conduct work near moving parts of the machine. This means that there is always a potential risk from the moving parts.
- Page 5 SAFETY PRECAUTIONS Danger An accident means ＂to cause personal injury or death, or damage to property.＂ When it is necessary to perform service on electrical parts, be sure to turn the power off and wait for 5 minutes or more before opening the power cabinet/box in order to avoid electrical shock.
- Page 6 6. Remove the power plug by holding the plug section instead of the cord to avoid electrical shock, leakage, or fire accident. 7. Turn off the power whenever the machine is left unattended between works. 8. In case of a power failure or black out, turn off the power to avoid damage or accident. 9.
- Page 7 (2) Check and make sure the pulley rotation follows the same direction as labels. (3) Make sure all the stand casters are locked or fixed in position. (4) Keep the working area clean from obstacles. 5. During Operation (1) Always keep your fingers, hair, or clothing away from the moving components and moving area. Do not place your personal belongings on the machine.
- Page 8 SAFETY INSTRUCTION FOR EBJ SERIES Parts moving area Always keep the moving area clean and free from any object. Area with moving parts Power Switch Always turn off the power when: 1. Performing service. 2. When the machine is left unattended between works.
- Page 9 EMG Stop 1. When there is an emergency, press EMERGENCY Urgent machine halt switch stop to stop the machine. 2. It is strongly advised to press EMERGENCY stop before turning off the power. Resume to work by turning on the power and release EMERGENCY stop.
-
Page 10: Table Of Contents
PAGE CONTENT SPECIFICATION INSTALLATION CONTROL PANEL FEEDING THE BAND SETTING THE BAND SETTING THE BUTTED SEAM AND OVERLAPPING AREA AUTO MODE TROUBLE SHOOTING TESTING MODE SERVICE & MAINTENANCE PART LIST... -
Page 11: Specification
SPECIFICATION Model ASP-EBJ100 ASP-EBJ100S Type of Needle DP x 5 # 14 Sewing Speed 2500 rpm (max) Varies per stitches Output Capacity i.e. thread patter 172 stitches : 9 sec/cycle Band Width 20 ~ 50 mm Power Single phase; 220V +/-10%; 50/60Hz Pneumatic 0.5 Mpa... -
Page 12: Installation
INSTALLATION ※ For safety issue, we strongly advise to have 2 technicians work together to install. 1. Unscrew screws ① , and move the Band Feeding Detector ② outward. (move with caution, do not damage the wire of the detector) 2. - Page 13 6. Pneumatic: Set the air pressure at 0.5Mpa. ④ ③ 7. Power: The power input must be in good quality in less than 10% fluctuation. The grounding must be connected properly. 8. Lubrication: (1) For the lubrication of the sewing machine, please refer to the sewing machine manual.
-
Page 14: Control Panel
CONTROL PANEL 1. Setting Button ① ⑤ ⑩ ⑥ ⑦ ⑧ 重疊量 LAPPING SIZE ② ③ ④ ⑨ Item Description ① POWER Switch To turn on/off the power 1. To start the work cycle (Auto Mode) (p.14) ② START (green) 2. - Page 15 2. Indicator ⑪ 重疊量 LAPPING SIZE ⑫ ⑬ ⑭ Item Description 1. On when the power is ON ⑪ POWER 2. Auto Kit works alone mode 3. Starting one work cycle 1. On when EMG STOP pressed. ⑫ STOP 2. When complete a band circling operation continuously 1.
-
Page 16: Feeding The Band
FEEDING THE BAND ※ Caution: a band with wrinkle or rumple may cause quality issue or even damage to the machine. Part A. Open the induce plate ① and supporting roller ② . Insert the band through. (*1) Part B. 1. -
Page 17: Setting The Band
SETTING THE BAND It is necessary to adjust for the 1st work or when working with bands with different width or thickness. 1. To adjust induce plate sensing range: When the band goes through the wall ① and the induce plate ②... -
Page 18: Setting The Butted Seam And Overlapping Area
SETTING THE BUTTED SEAM AND OVERLAPPING AREA Part 1: Initial Mechanical Setting (Preset done by maker. No need to apply step 1~5 unless a significant overlapping difference, i.e. greater than 11mm). For general operation setting, simply go to control panel setting (Part 2) 1. - Page 19 Part 2: Overlapping setting for operation. ⑫ 6. When band circling is ready for sewing, the band´s left end ⑦ and right end ⑧ should ⑦ left end ⑧ right end align with the red line ⑩ on the feeding plate ⑨ . 7.
-
Page 20: Auto Mode
AUTO MODE Part 1: Setting Sewing Pattern: 1. Turn on the power. 2. On the sewing machine control panel, press READY ① , and then the SEWING indicator ② goes off. 3. Press SELECT ③ to select PATTERN NO. ④ . Press +/FORWARD ⑤... - Page 21 Sewing Pattern List Number Sewing size Number Sewing size Stitch Stitch Length Cross Length Cross diagram diagram stitches stitches width width width width 1. Example of Y-SCALE setting To work with a band width 34mm, applying pattern listed above (1) Select pattern No. 35. (2) ???????
- Page 22 Part 2: Start working with Auto Mode: 1. Feed the band (refer to the chapter of Feeding The Band) 2. Set the band length. L (Folding Length) (1) Go the LENGTH ① on the control panel for setting. The effective setting range is 150~990 (mm).
- Page 23 5. Reset the starting position of the band. (when there is an interruption.) (1) The setting of band starting position will run automatically when you turn on the power first time. ③ (2) In case of reloading the band or resuming from an interruption, to make sure the circling band length is correct, press and hold RESET ③...
-
Page 24: Trouble Shooting
TROUBLE SHOOTING Operation Panel Sewing Machine Operation Panel ⑤ ⑥ ⑦ 重疊量 LAPPING SIZE ① ② ③ ⑨ ⑪ ⑧ ④ ⑬ ⑭ ⑮ ⑩ ⑫ Indicator Status Description Solution STOP ① EMERGENCY ⑤ pressed 1. Band runs out. 2. Bad joint detected BAND ②... - Page 25 Solution A2: To reload the band 1. Take off the remaining band. Do not press RESET beforehand. 2. Press RESET ⑧ to set the machine back to origin position. 3. Reload the band. The indicator BAND ② should go off then. 4.
-
Page 26: Testing Mode
TESTING MODE ② 重疊量 LAPPING SIZE ③ ④ ① ⑤ A. To complete one work cycle. To make sure all the movement timing and the devices´ positions. 1. Press and hold CYCLE STOP ① , and turn on the power at the same time. 2. -
Page 27: Service & Maintenance
SERVICE & MAINTENANCE A.Band & Band Feeder Position 1. Disconnect the air supply. Loosen the Screw ② to adjust the distance between Band Locator ① and Needle Holder to be 4.5 ~ 5mm. 2. When the band reaches the presser foot, the inner side of the band should align with the Locator ① . Refer to Testing Mode to verify the position. - Page 28 B.Correct the variance of band joining. 1. When the right end of the circled band strays inward. (as shown below in the left): Loosen screw ① . Move the Band Clipper ② outward (direction 3). 2. When the right end of the circled band strays outward : Loosen screw ①...
- Page 29 D.Feeding Roller You need to adjust the Feeding ⑨ Roller ① when the band on the feeding roller moves outward. 1. Loosen screws ④ ④ 2. Adjust the Aux Roller ⑤ . Refer to the illustration as shown in the right below.
- Page 30 E. Presser Foot and Fabric Plate 1. Uninstall the needle. Enter the sewing machine solely running ⑥ mode. (Testing Mode B) 2. Set sewing pattern 3. Press RESET ⑥ to lower the presser foot. 4. Press +/FORWARD ⑦ . Move the Presser Foot ⑧...
- Page 31 G.Band Remaining Sensor When the band material is white or thin enough to allow the light going through, there might be a mis-reading. Then you need to adjust the sensor accordingly. 1. Turn on the power. 2. Insert the test band into the sensor.
- Page 32 4. Remove the screws ⑧ , ⑨ to change the Fixed Cutter ⑦ . 5. The blade of Fixed Cutter ⑦ should be 2mm lower than BASE ⑩ . ⑩ ⑨ ⑧ ⑦ To adjust the cutters: 6. As shown below, the Steel Rod ②...
- Page 53 選配圖...
- Page 54 選配圖...
- Page 55 選配圖...
- Page 56 由於對產品的改良及更新，本產品使用說明書中與零件圖之產品及外觀的修改恕不事先通知 ! The specification and/or appearances of the equipment described in this instruction book & parts list are subject to change because of modification which will without previous notice. ASP-EBJ100.OCT.2018...