Danfoss AK-CC55 User Manual page 36

User Guide | Controller for appliance control, AK-CC55
Multi Coil - continued
Appliance cleaning. 0=no Appliance cleaning. 1=Fans only. 2=All
output Off.
Selection of wiring diagram. See overview on pages 13-14
Access code 2 (partial access)
Replace the controller's factory settings with the present settings
Input signal on DI3. Function: (high voltage input)
0=not used. 1=status on DI2. 2=door function with alarm when open.
3=door alarm when open. 4=defrost start (pulse signal). 5=ext. main
switch. 6=night operation. 7=thermostat band changeover (activate
r21). 8=Not used. 9=Not used. 10=Appliance cleaning (pulse signal).
11=forced cooling at hot gas defrost. 12=Open night cover. 13=Not
used. 14=Refrigeration stopped (forced closing). 15=case shutdown.
16=light. 20=Refrigerant alarm. 21= adaptive liquid control when
short-circuited.
Rail heat control
0=not used, 1=pulse control with timer function (o41 and o42),
2=pulse control with dew point function A
Dew point value where the rail heat is minimum
Dew point value where the rail heat is 100% on
Lowest permitted rail heat effect in %
Time delay from "open door" refrigeration is started
Fan operation at stopped cooling (forced closing):
0 = Stopped (defrost allowed)
1 = Running (defrost allowed)
2 = Stopped (defrost not allowed)
3 = Running (defrost not allowed)
Display of temperature
1 = Thermostat air
2 = Average all
3 = Maximum all
Light and night blinds defined:
0: Light is switched off and night blind is opened when the main
switch is off
1: Light and night blind is independent of main switch
Configuration of alarm relay:
The alarm relay will be activated by an alarm in one or more of the
following priorities.
Setting:
0 = The relay is not activated by alarms
1 = Only high priority alarms
2 = High priority and intermediate priority alarms
3 = High priority, intermediate priority and low priority
Cycle time for rail heat at PWM on AO1
User defined refrigerant 3-digit Rfg. factor K1
User defined refrigerant 3-digit Rfg. factor K2
User defined refrigerant 3-digit Rfg. factor K3
Max. limitation of the superheat reference when regulated with liquid-
filled evaporator
Min. limitation of the superheat reference when regulated with liquid-
filled evaporator
Access code 1 (simple access)
Locking the display control. 0/Off=operation. 1/On=locked
Configuration of analogue output AO1: 0=not used. 1=rail heat PWM
Manual control of output: AKV valve 0-100%
Manual control of output: Fan
Manual control of output: Defrost A
Manual control of output: Rail heat
Manual control of output: Alarm
Manual control of output: Light
Manual control of output: Defrost B
Manual control of output: Heating element
Manual control of output: Humidity
Manual control of output: Rail heat PWM
36 | BC308437742037en-000101
R-W Code 1 2 3 4
1-2 o46 1 1 1 1
1-3* o61 1 1 1 1
2-2 o64 1 1 1 1
3-3* o67 1 1 1 1
1-2* o84 1 1 1 1
1-2 o85 1 1 1 1
1-2 o86 1 1 1 1
1-2 o87 1 1 1 1
1-2 o88 1 1 1 1
1-2 o89 1 1 1 1
1-2 o90 1 1 1 1
1-2 o97 1 1 1 1
1-2 o98 1 1 1
1-2 P41 1 1 1 1
1-2 P82 1 1 1 1
1-3* P83 1 1 1 1
1-3* P84 1 1 1 1
1-3* P85 1 1 1 1
1-2 P86 1 1 1 1
1-2 P87 1 1 1 1
1-1 P88 1 1 1 1
1-2 P89 1 1 1 1
1-3* q09 1 1 1 1
1-2** q11 1 1 1 1
1-2** q13 1 1 1 1
1-2** q14 1 1
1-2** q15 1 1 1
1-2** q16 1 1 1
1-2** q17 1 1 1 1
1-2** q22 1
1-2** q23 1
1-2** q26 1
1-2** q27 1 1 1 1
5 Min. Max. Fac.
1 0 2 0
1 1 9 1
1 0 999 0
1 0/Off 1/On 0/Off
1 0 21 0
1 0 2 0
1 -10 °C ""o87 8
1 "o86" 50 °C 17
1 0 % 100 % 30
1 0 min. 240 min. 30
1 0 3 1
1 1 3 1
1 0 1 0
1 0 3 2
1 4 sec 60 sec 10
1 -999 999 300
1 -999 999 300
1 -999 999 300
1 "P87" 20°C 3
1 0°C "P86" 1
1 0 999 0
1 0/Off 1/On 0/Off
1 0 1 0
1 0 % 100 % 0
1 0/Off 1/On 0/Off
1 0/Off 1/On 0/Off
0/Off 1/On 0/Off
1 0/Off 1/On 0/Off
1 0/Off 1/On 0/Off
1 0/Off 1/On 0/Off
0/Off 1/On 0/Off
0/Off 1/On 0/Off
1 0 % 100 % 0
© Danfoss | DCS (vt) | 2019.09
Actual