Safety Of Persons; Use And Handling Of The Power Tool; Service; Intended Use - HellermannTyton Autotool 2000 CPK Operating Instructions Manual

2 .1 .3 Safety of persons

a) Stay alert, attend to the task in hand and use
common sense when you work with a power tool.
Do not use a power tool when you are tired or while
under the influence of drugs, alcohol or medication.
A moment of inattention while using a power tool can
result in serious injuries.
b) Wear appropriate personal protective equipment
(PPE). Depending on the type of power tool and the
way in which it is used, wearing PPE such as a dust
mask, non-slip safety shoes, a hard hat and ear
defenders reduces the risk of injury.
c) Prevent accidental starting. Make sure that the
power tool is switched off before you connect it to
the power source and/or battery pack, and also
before picking up or carrying the tool. Touching the
switch while carrying the power tool or connecting the
power tool to the electricity supply while it is switched
on can lead to accidents.
d) Remove adjusting tools or wrenches before
switching the power tool on. A tool or wrench
engaged in a part that starts to rotate when the power
tool is switched on can cause injuries.
e) Avoid adopting an awkward posture when working.
Maintain a firm footing and keep your balance at all
times. This will enable you to control the power tool
better if an unexpected situation occurs.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing well away
from moving parts. Loose clothes, jewellery or long
hair can be snagged by moving parts.
g) If it can be fitted, dust extraction and filtration
equipment must be connected and used correctly.
Using a dust extractor can reduce hazards associated
with dust.
h) Do not permit yourself to be lulled into a false sense
of security and do not disregard the safety
regulations for working with power tools, even after
frequent or repeated use has made you familiar with
the power tool. Carelessness can result in series injuries
within a fraction of a second.

2 .1 .4 Use and handling of the power tool

a) Do not overload the power tool. Use the correct
power tool for the task in hand. Using the right power
tool for the job will enable you to work better and in
greater safety in the stated performance range.
b) Never use a power tool that has a faulty switch. A
power tool that cannot be switched on or off at the
switch intended for this purpose is dangerous and must
be repaired.
Operating Instructions • AT2000 CPK • 07-2019 • v03 • 106-29004
c) Disconnect the plug from the socket outlet and/or
remove the battery pack from the power tool before
making adjustments, changing accessory tools or
laying the power tool aside. This precaution prevents
accidental starting of the power tool.
d) When not in use, store power tools out of reach of
children. Do not permit anyone to work with the
power tool who is not familiar with it or has not
read and understood these instructions. Power tools
in the hands of inexperienced persons are dangerous.
e) Keep power tools and accessory tools in good
condition at all times. Check that moving parts are
in full working order and do not jam. Check for
parts that are broken or damaged to the extent that
operation of the power tool is impaired. Have
damaged parts repaired before using the power tool.
Many accidents involving power tools are due to poor
maintenance.
f) Keep cutting tools sharp and clean. Carefully
maintained cutting tools with sharp cutting edges are
less likely to jam and are easier to control.
g) Use the power tool, accessory tools, etc. in
accordance with these instructions. Take working
conditions and the task to be undertaken into
account in this respect. Using power tools for other
than the intended use can lead to hazardous situations.
h) Keep handles and gripping surfaces dry, clean and
free of oil and grease. Slippery handles and gripping
surfaces do not permit safe operation and control of the
power tool in unexpected situations.

2 .1 .5 Service

a) Have your power tool repaired only by a qualified
specialist using only the manufacturer's genuine
spare parts. This ensures that the safety of the power
tool is maintained.
2 .2

Intended use

Use the AT2000 CPK only when it is in full working order
and safe, always be safety-conscious and aware of the
hazards.
The AT2000 CPK is suitable for and intended for the
following uses:
• Automatic binding of bundles up to a diameter of max.
80 mm
• Use indoors and, under rainproof roofing, outdoors
• Industrial use
Safety warnings
7