Aux Output Status Message; Power-On Status Message; Power-Off Status Message; Status List - Kenwood TK-3180 Function Reference

22 FLEETSYNC
To enable this function, you must configure the Status
Message to the AUX IN terminal.
You can configure the Aux Input Status Message using
KPG-89D.
!
Configuration using KPG-89D
• Configuring the AUX Input Status Message (Refer
to FPRG 6.12.7 Target tab - AUX Input Status
Message 1 - 3.)

22.3.8 AUX Output Status Message

This function allows a user to alternate the Status of the
AUX OUT terminal (High > Low or Low > High) when
receiving the Status Message. The user can use this
function to remotely turn the external device On/Off.
To enable this function, you must configure the Status
Message to the AUX Out terminal.
You can configure the AUX Output Status Message using
KPG-89D.
!
Configuration using KPG-89D
• Configuring the AUX Output Status Message
(Refer to FPRG 6.12.7 Target tab - AUX Output
Status Message 1 - 3.)

22.3.9 Power-on Status Message

This function allows the transceiver to send the Status
Message when the transceiver is turned ON.
With this function enabled, the dispatcher acknowledges
that the transceiver is turned ON. The transceiver sends
the status message to the FleetSync ID configured with
the Target Fleet/ID (Status Message).
You can configure the Power-on Status Message using
KPG-89D.
!
Configuration using KPG-89D
• Configuring the Power-on Status Message (Refer
to FPRG 6.12.7 Target tab - Power-on Status
Message.)

22.3.10 Power-off Status Message

This function allows a user to send the Status Message
when the transceiver is turned OFF.
With this function enabled, the dispatcher acknowledges
that the transceiver is turned OFF. The transceiver sends
the status message to the FleetSync ID configured with
the Target Fleet/ID (Status Message).
You can configure the Power-off Status Message using
KPG-89D.
106
!
Configuration using KPG-89D
•
Configuring the Power-off Status Message (Refer
to FPRG 6.12.7 Target tab - Power-off Status
Message.)

22.3.11 Status List

The Status Message must be configured to the
transceiver prior to the transmission. A user can store a
maximum of 90 Status Messages in the Status List.
You can configure the Status List using KPG-89D. The
Status List has the following functions.
Call Type
Status
Status Name
TX Inhibit
!
Configuration using KPG-89D
•
Configuring the Status List (Refer to FPRG 6.12.5
Status List tab.)
22.3.12 Target Fleet/ID
The Target Fleet/ID is the receiving party's FleetSync
identification to receive the following Status Messages.
•
Status Message transmission using the AUX IN
terminal
• Power-on Status Message transmission
• Power-off Status Message transmission
• Status Message transmission using the PF Call 1 - 6
keys
• Status Message transmission after entering Status
Message Mode by pressing the PF Status key.
You can configure the Target FleetSync ID using KPG-
89D. The FleetSync ID of the Base Station is normally
used.
Function Reference
Table 22-10 Selective Call Type
Description
You can configure the Status Number. You can
configure the number between 10 and 99.
You can configure the Status name. It is hard to
understand the operation of the Status only with
the Status Number. In this case, you can put a
name to the Status. You can configure a
maximum of 16 characters to each Status
name.
You can enable/disable the transmission to the
receiving party.
When the transmission is inhibited, the status
does not appear on the Status Selection
window. Therefore, a user cannot select the
Status in Message Mode if the transmission is
inhibited.
(Status Message)
Version: 1.11