Ac Control; Priority 1 Temporary Delete/Add; Priority 2 Temporary Delete/Add; Off-Hook Scan - Kenwood TK-3180 Function Reference

23 SCAN

23.7.11 AC Control

This function allows a user to activate the Carrier Squelch
after deactivating the QT/DQT on the Priority Channel
during Priority Scan. The user can quickly jump to the
Priority Channel since the transceiver does not need to
check the QT/DQT.
The user can hear conversations on the Priority Channel
even if another QT/DQT group is using the same Priority
Channel.
!
Configuration using KPG-89D
•
Configuring the AC Control (Refer to FPRG 6.9.11
AC Control.)
23.7.12 Priority 1 Temporary Delete/
Add
This function allows a user to temporarily delete the
Priority Channel 1 by pressing the PF Scan Del/Add key
when scan pauses on Priority Channel 1 in Scan Mode.
!
Configuration using KPG-89D
•
Configuring the Priority 1 Temporary Delete
function (Refer to FPRG 6.9.12 Priority 1
Temporary Delete/Add.)
23.7.13 Priority 2 Temporary Delete/
Add
This function allows a user to temporarily delete the
Priority Channel 2 by pressing the PF Scan Del/Add key
when scan pauses on Priority Channel 2 in Scan Mode.
!
Configuration using KPG-89D
•
Configuring the Priority 2 Temporary Delete
function (Refer to FPRG 6.9.13 Priority 2
Temporary Delete/Add.)

23.7.14 Off-hook Scan

(TK-7180/ 8180 only)
This function allows you to configure the scan operation
in conjunction with the Mic hook status. You can
configure the scan operation as below.
134
Table 23-7 Off-hook Scan Operation
Off-hook
Scan
Check
(Enable)
Uncheck
(Disable)
!
Configuration using KPG-89D
• Configuring the Off-hook Scan (Refer to FPRG
6.9.14 Off-hook Scan.)

23.7.15 Revert CH/GID Display

This function allows the transceiver to display the Revert
Zone-CH/GID on the display during scan.
!
Configuration using KPG-89D
•
Configuring the Revert CH/GID Display (Refer to
FPRG 6.9.15 Revert CH/GID Display.)

23.7.16 CH/GID Recall

This function allows the transceiver to move to the Last
Called Zone-CH/GID when the PF CH/GID Recall key is
pressed during scan. A user can move to the last
received Zone-CH/GID when receiving a call during scan
while he/she is away from the transceiver.
Note:
" When the PF CH/GID Recall key is pressed while no signal is
received after scan starts, the transceiver moves to the Scan
Start CH/GID.
" When the CH/GID Recall function is enabled, the transceiver
does not resume scan even if the Dropout Delay Time or the
Dwell Time expires.
" The CH/GID Recall function is disabled when changing the CH/
GID. The transceiver resumes scan after the Key Dwell Time
expires.
" The Looolback function will not be activated while performing
the CH/GID Recall function.
!
Transceiver Operation
# The transceiver moves to the Last Called Zone-
CH/GID.
•
Press the PF CH/GID Recall key during scan.
Function Reference
Operation
The transceiver activates scan when the PF
Scan key is pressed regardless of the status of
the microphone.
The transceiver activates scan when the PF
Scan key is pressed if the microphone is in On-
hook status. Scan does not start when the
microphone is Off-hook.
Scan pauses on the Revert CH/GID pauses
when switching the Scan Mode from On-hook to
Off-hook. The repeater resumes scan when the
microphone returns to the On-hook position.
Version: 1.11