Status Message Stack; Status Message On Data Zone-Ch/Gid; Status Message Serial Output; Aux Input Status Message - Kenwood TK-3180 Function Reference

*1 You can enable/disable the Status 80 - 99 when using the Manual
Dialing function with KPG-89D.
(Special).)
*2 The Horn Alert terminal does not activate when the Off-hook
Horn Alert function is disabled and the microphone is in the Off-
hook position.
*3 In this case, the Stun Status does not change even if a user
changes the Status in Status Mode.
*4 You can enable/disable the Status 80 - 99 when using the Manual
Dialing function with the KPG-89D.
99 (Special).)
!
Emergency
When the transceiver receives the reserved status
message, the Alert or both of the Alert and Horn is
activated according to the Emergency Status
Response configuration.
!
Remote Stun
This function allows you to disable almost all the
transceiver's functions. Only the following operations
function when the Stun function is enabled. The
transceiver recovers from the Stun status when
receiving the Stun Deactivation status message or the
Status Deactivation command by DTMF.
Table 22-9 Status Message Output
Status Message Inhibit TX.
Normal Operation Inhibit TX.
The transceiver does
not accept the
PC Control transmission request.
It does not output the
received data.
!
Status 90 - 92
These statuses allow you to command or reset the Stun
function.
This function operates regardless of the Stun status of the
receiving party's transceiver.
!
Status 93 - 94
These statuses are used to respond to the Stun status
of the transceiver when receiving the RSTM (Request
Status).

22.3.4 Status Message Stack

This function is used to store the received Status
Message in the Stack memory. The transceiver can store
a maximum of 15 Status Messages.
When the message is stacked, the "
this case, a user can read the stored Status Message by
entering Stack Mode. (Refer to 22.7 Stack.)
Version: 1.11
(Refer to 22.3.13 Status 80 - 99
(Refer to 22.3.13 Status 80 -
Inhibit TX/RX.
Inhibit TX/RX.
The transceiver does
not accept the
transmission request.
It does not output the
received data.
" icon blinks. In
Function Reference
You can configure the Status Message to be stacked
using KPG-89D.
Note: The transceiver can stack a maximum of 15 Status
Messages.
!
Configuration using KPG-89D
•
Configuring the Status Message Stack (Refer to
FPRG 6.12.2 General 2 tab - Status Message
Stack.)
22.3.5 Status Message on Data Zone-
CH/GID
This function allows the transceiver to automatically
change the Data Zone-CH/GID to send the Status
Message.
The transceiver automatically changes the channel to
Data Zone-CH/GID to transmit the Status Message. The
transceiver returns to the previous Zone-CH/GID when
the transmission ends. This function allows a user to
send data using the selected Zone-Channel/Group ID.
You can enable/disable this function using KPG-89D.
!
Configuration using KPG-89D
• Configuring the Status Message on Data Zone-CH/
GID function (Refer to FPRG 6.12.3 Parameter
tab - Status Message on Data Zone-CH/GID.)

22.3.6 Status Message Serial Output

This function allows the transceiver to send the caller's
Fleet/ID from the transceiver's communication port when
the transceiver receives a Status Message.
The dispatcher can remote control the transceiver with a
PC. It can also retrieve the transceiver's status
information by connecting external devices.
You can enable/disable this function using KPG-89D.
!
Configuration using KPG-89D
• Configuring the Status Message Serial Output
(Refer to FPRG 6.12.2 General 2 tab - Status
Message Serial Output.)

22.3.7 AUX Input Status Message

This function allows the transceiver to send the Status
Message when the status of the AUX IN terminal
alternates to low from high.
You can send the Status Message by connecting
sensor to the AUX IN terminal. The transceiver sends the
status message to the FleetSync ID configured
Target Fleet/ID (Status Message).
22 FLEETSYNC
a
in the
105