Mitsubishi Electric Melsec QJ71LP21 Reference Manual page 280

7 APPLICATION FUNCTIONS
Control data
Device Item
Error completion
(S1)+0
type
(S1)+1 Completion status
Channel used by
(S1)+2
host station
Target station's
(S1)+3
CPU type
Target station
(S1)+4
network No.
(S1)+5 Target station No.
(S1)+6 (Use prohibited)
(S1)+7 Number of resends
5: The setting side is as shown below.
User : It is data the user sets in the sequence program before execution of a link dedicated instruction.
System: The programmable controller CPU stores the execution result of the link dedicated instruction.
6: The CPU type can be specified when the host station is a network module of which function version is either D or later or the following.
• Network module: Serial number (first five digits) "10101" or later
(The CPU module cannot be specified in the case other than the above. Only access to the control CPU is available.)
7: The CPU type can be specified when the QCPUs and network modules of the host station or target station are the following versions.
• Network module: Serial number (first five digits) "06092" or later
• QCPU: Serial number (first five digits) "06092" or later
(The CPU module cannot be specified in the case other than the above. Only access to the control CPU is available.)
7 - 56
b15 to
0
1) Error completion type (bit 7)
Specify the clock data setup status for error completion.
0: Clock data at the time of error completion is not set in the area starting from (S1)+11.
1: Clock data at the time of error completion is set in the area starting from (S1)+11.
The instruction completion status is stored.
0 : Normal
Other than 0 : Error (Refer to Section 8.3 for error codes)
Specify the channel used by the host station.
1 to 8: Channel
Specify the CPU module on the station to be accessed.
Setting value
Target station CPU/control CPU/own system CPU
0000 Control CPU (The access target is the same as when "03FF
H
specified.)
03D0 6 Control system CPU
H
03D1 6 Standby system CPU
H
03D2 6 System A CPU
H
03D3 6 System B CPU
H
 Control CPU (single CPU system)
03E0 7
H
 Multiple CPU system No.1
03E1 7 Multiple CPU system No.2
H
03E2 7 Multiple CPU system No.3
H
03E3 7 Multiple CPU system No.4
H
03FF 6 Control CPU
H
When the instruction is executed with control system CPU (03D0
(03D1 ) specified, if system switching occurs at the target station, the instruction execution
H
may fail. (Error code: 4244 , 4248
H
If the instruction has failed with the above error, execute it again.
Specify the network No. of the target station.
1 to 239 : Network No.
254 : Specify this when 254 has been set in Jn.
Specify the station No. of the target station.
1 to 64: Station No.
1) For instruction execution
Specify the number of times the instruction is to be resent when it is not completed within
the monitoring time specified in (S1)+8.
2) At instruction completion
The number of resends executed (result) is stored.
Setting data
b7 to
1) 0
Description
) or standby system CPU
H
)
H
MELSEC-Q
Setting range
b0
1
0001
H
0081
H
1 to 8
" is
H
0000
H
03D0 to 03D3
H
03E0 to 03E3
H
03FF
H
1 to 239
254
1 to 64
0 to 15
(Continued to the next page)
Setting
side 5
User
System
User
H
User
H
User
User
User
System
7 - 56