ABB SYN 5201 Operating Instructions Manual page 33

Operating Instructions
Parameter sets 1 to 7
1. Actual value calibration "Calibrate act values"
No. Parameter name
1. Nominal voltage
2. Nominal frequency
3. Voltage tuning
4. Angle tuning
2. Command generation "Paralleling cmd gen"
No. Parameter name
1. Test function
2. Paralleling time
3. Paralleling command duration
4. Monitoring time
5. Multiple commands
3. Paralleling conditions "Parallel conditions"
No. Parameter name
1. Slip limit, oversynchronous
2. Slip limit, sub-synchronous
3. Angle limit, negative
4. Angle limit, positive
5. Max. voltage difference, overexcited
6. Max. voltage difference, underexcited
7. Maximum voltage
8. Minimum voltage
4. "Dead bus conditions"
No. Parameter name
1. Maximum zero voltage
2. Release U1 = no-voltage
3. Release U2 = no-voltage
4. Release for U1 and U2 = no-voltage
5. "Voltage matcher"
No. Parameter name
1. Test function
2. Voltage adjustment characteristic
3. Pulse interval
4. Minimum pulse duration
5. Switchover to variable intervals
6. Switchover to tap changer
6. "Frequency matcher"
No. Parameter name
1. Test function
2. Frequency adjustment characteristic
3. Pulse interval
4. Minimum pulse duration
5. Switchover to variable intervals
7. "General parameters"
No. Parameter name
1. Blocking time after selection
2. Total paralleling time
abb
ABB Switzerland Ltd
Template: CHIND Techn doc stand, A4 P de, R1.DOT; Filename: 3BHS109762E01 D.doc; Print: 12/6/2011 5:48:00 PM; Save: 12/1/2011 2:37:00 PM; CHIND No. 3BHS109763 ZAB D14 Rev. -; I-Q
Symbol Range/resolution
Un 50 to 130
2
fn 16 / , 50, 60
3
UOffset 12.0
Offset 180
Symbol Range/resolution
TEST ton ON/OFF
t on 0 to 990/10
tp on OFF, 10 to 990/10
t supervis 0 to 99
MULTIPLE CMD ON/OFF
Symbol Range/resolution
-smax 0.00 to 6.00
+smax 0.00 to 6.00
0 to 99
-max
0 to 99
+max
0 to 40
-Umax
0 to 40
+Umax
Umax 105 to 130
Umin 50 to 95
Symbol Range/resolution
U0max 0 to 49
U1not ON/OFF
U2not ON/OFF
1*2not ON/OFF
Symbol Range/resolution
TEST U-Match ON/OFF
dU/dt 0.00 to 5.00
ts U 1 to 20
tp Umin 0.05 to 2.00
INVERSE U ON/OFF
TAP CHANGER ON/OFF
Symbol Range/resolution
TEST f-Match ON/OFF
df/dt 0.00 to 5.00
ts f 1 to 120
tp fmin 0.05 to 2.00
INVERSE f ON/OFF
Symbol Range/resolution
t block 1 to 10
t tot OFF, 0.5 to 15/
Steps: 0.5
Document No Art Part
3BHS109762 E01
SYN 5201/SYN 5202
Unit Default setting of all
parameter sets
VAC 110
Hz 50
% 0
DEG 0
Unit Default setting of parameter
sets
1 to 6 7
- OFF OFF
ms 100 100
ms 990 OFF
s 10 10
- OFF OFF
Unit Default setting of parameter
sets
1 to 6 7
% 0.4 0.2
% 0.4 0.2
DEG 10 10
DEG 10 10
% 3 3
% 3 3
% 120 120
% 80 80
Unit Default setting of all
parameter sets
% 5
- OFF
- OFF
- OFF
Unit Default setting of parameter
sets
1 to 6 7
- OFF OFF
%/s 0.30 0.00
s 2 2
s 0.05 0.05
- OFF OFF
- OFF OFF
Unit Default setting of parameter
sets
1 to 6 7
- OFF OFF
%/s 0.20 0.00
s 20 20
s 0.05 0.05
- OFF OFF
Unit Default setting of all
parameter sets
s 2
min 5
Language Revision
en D
page
33