Table of Contents
Advertisement
--------------------------------------------------------HMCS45C,HMCS45CL
• ELECTRICAL CHARACTERISTICS-1 (Vee=5V±10%. Ta=-20'C to +75'C)
Value
Item
Symbol
Test Conditions
min.
typo
Input "Low" Voltage
V,L
-
-
Input "High" Voltage (1)
V,HI
Vee- 1 .O
-
Input "High" Voltage (2)
V,H2
Vee- 1 .O
-
Output "Low" Voltage
VOL
IOL=1.6mA
-
-
Output "High" Voltage (1)
VOHI
-loH=1.0mA
2.4
-
Output "High" Voltage (2)
VOH2
-loH=O.Ol mA
Vec- 0 .3
-
Interrupt Input Hold Time
tiNT
2·Tinst
-
Interrupt Input Fall Time
tfiNT
-
-
Interrupt Input Rise Time
trlNT
-
-
Output "High" Current
IOH
VOH=10V
-
-
Vin=O to Vce
-
-
Input Leakage Current
IlL
Vin=O to 10V
-
-
Pull up MOS Current
-Ip
Vcc=5V
60
-
Vin=V cc •
Supply Current (1)
Icc I
Ceramic Filter
-
-
Oscillation
Vin=V cc •
Supply Current (2)
Icc2
Rf Oscillation.
~
~
External Clock Operation
- - _
.1
Vin=O to Vcc
-
-
Standby I/O Leakage Current
ks
HLT -1.0V
1
.
-0
10V
V,n-
to
~
-
Standby Supply Current
Ices
Vin=V cc • HLT=0.2V
-
-
External Clock Operation
External Clock Frequency
fcp
200
400
External Clock Duty
Duty
45
50
External Clock Rise Time
trcp
0
-
External Clock Fall Time
tfcp
0
-
Instruction Cycle Time
Tinst
Tinst=4/f cp
9.1
10
Internal Clock Operation (Rf Oscillation)
Clock Oscillation Frequency
Rf=91kO±2%
Clock Oscillation Frequency
Ceramic Filter Circuit
Instruction Cycle Time
Tinst=4/fos c
[NOTE 1) All voltages are with respect to GND.
[NOTE 2) This is applied to RESET.
HIT.
OSC,. INTo. INTt and the With Pull up MOS or CMOS type of I/O pins.
[NOTE 3) This is applied to the Open Drain type of I/O pins.
[NOTE 4) This is applied to the CMOS type of I/O or Output pins.
[NOTE 5) This is applied to the With Pull up MOS or CMOS type of I/O or Output pins.
[NOTE 6) This is applied to the Open Drain type of I/O or Output pins.
[NOTE 7) I/O current is excluded.
[NOTE 8) The Standby I/O Leakage Current is the I/O leakage current in the Halt and Disable State.
[NOTE 9) I/O current is excluded.
Unit
max.
1.0
V
Vee
V
10
V
0.8
V
-
V
-
V
-
J.l.s
50
J.l.S
50
J.l.S
3
J.l.A
1.0
3
J.lA
250
J.lA
2
mA
1.0
mA
1
J.l.A
3
J.lA
10
J.l.A
440
kHz
55
%
0.2
J.l.S
0.2
J.l.s
20
J.l.S
The Standby Supply Current is the supply current at Vcc = 5V ± 10% in the Halt State. The supply current in the case where the supply
voltage falls to the Halt Duration Voltage is called the Halt Current
(lOH).
and it is shown in "ELECTRICAL CHARACTERISTICS-V'
63
Note
2
3
4
5
6
2
3
7
7
2. 8
3. 8
9
Advertisement
Table of Contents
