Table of Contents
Advertisement
--------------------------------------------------------HMCS47C,HMCS47CL
• ELECTRICAL CHARACTERISTICS-1 (Vee - 5V
±
10%, Ta - _20°C to +75°C)
Item
Symbol
Test Conditions
Value
min.
typo
Input "Low" Voltage
V 1L
-
-
Input "High" Voltage (1)
V 1Hl
Vee - 1.0
-
Input "High" Voltage (2)
V 1H2
Vee - 1.0
-
Output "Low" Voltage
VOL
IOL = 1.6mA
-
-
Output "High" Voltage (1)
V OHl
-l oH = 1.0mA
2.4
-
Output "High" Voltage (2)
V OH2
-loH
=
0.01 mA
Vee - 0.3
-
Interrupt Input Hold Time
tiNT
20Tinst
-
Interrupt Input Fall Time
tflNT
-
-
Interrupt Input Rise Time
trlNT
-
-
Output "High" Current
IOH
V OH = 10V
-
-
V
in
=
Oto Vee
-
-
Input Leakage Current
IlL
V
in
=
0 to 10V
-
-
Pull up MOS Current
-Ip
Vee = 5V
60
-
V
in
= Vee. Vee
=
5V.
Supply Current (1)
leel
Ceramic Filter
-
-
Oscillation
(folC
=
800kHz)
V
in
= Vee. Vee = 5V
R
f
Oscillation
Supply Current (2)
lee2
(folC
=
800kHz)
-
-
External Clock
Operation (fcp = 800kHz)
Standby I/O Leakage
HLT
I
V
in
= 0 to Vee
-
-
Current
I LS
= 1.0V
I
V
in
=
Oto 10V
-
-
Standby Supply Current
Ices
V
in
=Vee. HLT = 0.2V
-
-
External Clock Operation
External Clock Frequency
fcp
350
-
External Clock Duty
Duty
45
50
External Clock Rise Time
t
rcp
0
-
External Clock Fall Time
ttcp
0
-
Instruction Cycle Time
T
inst
T
inst
= 4/fcp
4.7
-
Internal Clock Operation (R t Oscillation)
Clock Oscillation Frequency
R t = 51kn
±
2%
Clock Oscillation Frequency
Ceramic Filter Circuit
Instruction Cycle Time
T
inst
=
4/f(JfK;
[NOTE
1
I
All voltages are with respect to GND.
[NOTE 21 This is applied to RESET. HLT. OSC,. INTo. INT, and the With Pull up MOS or CMOS
type
of I/O pins.
[NOTE 31 This is applied to the Open Drain
type
of I/O pins.
[NOTE 41 This is applied to the CMOS type of I/O or Output pins.
[NOTE 51 This is applied to the With Pull up MOS or CMOS
type
of I/O or Output pins.
[NOTE 61 This is applied to the Open Drain
type
of I/O or Output pins.
[NOTE 71 I/O current is excluded.
[NOTE 81 The Standby I/O Leakage Current is the I/O leakage current in the Halt and Disable State.
[NOTE 91 I/O current is excluded.
Unit
Note
max.
1.0
V
Vee
V
2
10
V
3
0.8
V
-
V
4
-
V
5
-
p.s
50
p.s
50
p.s
3
p.A
6
1
2
3
p.A
3
250
p.A
2.0
mA
7
0.85
mA
7
1
p.A
5.8
3
p.A
6.8
12
p.A
9
850
kHz
55
%
0.2
p.s
0.2
p.s
11.4
p.s
The Standby Supply Current is the supply current at VCC=5V
± 10%
in the Halt State. The supply current in the case where the supply
voltage
falls
to the Halt Duration voltage is called the Halt Current (lDH). and it is shown in "ELECTRICAL CHARACTERISTICS -2."
111
Advertisement
Table of Contents
