Parameters: 16-** Main Menu - Data Readouts - Danfoss VLT HVAC Drive FC 102 Programming Manual

Parameter Descriptions
3.16 Parameters: 16-** Main Menu - Data
Readouts
3.16.1 16-0* General Status
3 3
16-00 Control Word
Range:
0 [0 - 65535 ] View the control word sent from the frequency
*
16-01 Reference [Unit]
Range:
0 ReferenceFeed-
backUnit
*
16-02 Reference [%]
Range:
0 % [-200 - 200
*
%]
16-03 Status Word
Range:
0 [0 - 65535 ] View the status word sent from the frequency
*
16-05 Main Actual Value [%]
Range:
0 % [-100 - 100 %] View the 2-byte word sent with the status
*
16-09 Custom Readout
Range:
0 CustomRea-
doutUnit
*
130
VLT
Function:
converter via the serial communication port in
hex code.
Function:
[-999999 - View the present reference
999999 value applied on impulse or
ReferenceFeed- analog basis in the unit
backUnit] resulting from the configu-
ration selected in
parameter 1-00 Configu-
ration Mode (Hz, Nm, or
RPM).
Function:
View the total reference. The total reference
is the sum of digital, analog, preset, bus,
and freeze references, plus catch up and
slow down.
Function:
converter via the serial communication port in
hex code.
Function:
word to the bus master reporting the
main actual value.
Function:
[-999999.99 - View the user-defined readouts
999999.99 as defined in
CustomRea- parameter 0-30 Custom Readout
doutUnit] Unit, parameter 0-31 Custom
Readout Min Value, and
parameter 0-32 Custom Readout
Max Value.
Danfoss A/S © 03/2015 All rights reserved.
®
HVAC Drive FC 102
3.16.2 16-1* Motor Status
16-10 Power [kW]
Range:
0 kW [0 -
*
10000
kW]
16-11 Power [hp]
Range:
0 hp [0 -
*
10000 hp]
16-12 Motor Voltage
Range:
0 V [0 - 6000 V] View the motor voltage, a calculated value
*
16-13 Frequency
Range:
0 Hz [0 - 6500 Hz] View the motor frequency, without
*
16-14 Motor current
Range:
0 A [0 - 10000
*
A]
16-15 Frequency [%]
Range:
0 % [-100 -
*
100 %]
Function:
Displays motor power in kW. The value shown
is calculated based on the actual motor
voltage and motor current. The value is
filtered, and therefore approximately 1.3 s may
pass from when an input value changes to
when the data readout values change. The
resolution of readout value on fieldbus is in
10 W steps.
Function:
View the motor power in hp. The value
shown is calculated based on the actual
motor voltage and motor current. The value is
filtered, and therefore approximately 1.3 ms
may pass from when an input value changes
to when the data readout values change.
Function:
used for controlling the motor.
Function:
resonance damping.
Function:
View the motor current measured as a mean
value, I . The value is filtered, and thus
RMS
approximately 1.3 s may pass from when an
input value changes to when the data
readout values change.
Function:
View a 2-byte word reporting the actual motor
frequency (without resonance dampening) as a
percentage (scale 0000-4000 hex) of
parameter 4-19 Max Output Frequency. Set
parameter 9-16 PCD Read Configuration index 1
to send it with the status word instead of the
MAV.
MG11CE02