Specifications; Electrical Data, 380-480 - Danfoss VLT AQUA Drive FC 202 Design Manual

Specifications

7 Specifications
7.1 Electrical Data, 380–480 V
®
VLT AQUA Drive FC 202
High/normal load
(High overload=150% current during 60 s, normal
overload=110% current during 60 s)
Typical shaft output at 400 V [kW]
Typical shaft output at 460 V [hp]
Typical shaft output at 480 V [kW]
Enclosure size
Output current (3-phase)
Continuous (at 400 V) [A]
Intermittent (60 s overload) (at 400 V)[A]
Continuous (at 460/480 V) [A]
Intermittent (60 s overload) (at 460/480 V) [kVA]
Continuous kVA (at 400 V) [kVA]
Continuous kVA (at 460 V) [kVA]
Continuous kVA (at 480 V) [kVA]
Maximum input current
Continuous (at 400 V) [A]
Continuous (at 460/480 V) [A]
Maximum number and size of cables per phase
- Mains, motor, brake, and load share [mm
Maximum external mains fuses [A]
Estimated power loss at 400 V [W]
Estimated power loss at 460 V [W]
3)
Efficiency
Output frequency [Hz]
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C (°F)]
Table 7.1 Electrical Data for Enclosures D1h/D3h/D5h/D6h, Mains Supply 3x380–480 V AC
1) For fuse ratings, see chapter 10.5 Fuses and Circuit Breakers.
2) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies for
dimensioning of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control
card power consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-
efficiency-directive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for
slots A and B each add only 4 W.
3) Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy
efficiency class, see chapter 7.5 Ambient Conditions. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
MG22B222
Design Guide
2 (AWG)]
1)
2), 3)
2), 3)
Danfoss A/S © 01/2018 All rights reserved.
N110K N132
HO NO HO
90 110 110
125 150 150
110 132 132
D1h/D3h/D5h/D6h
177 212 212
266 233 318
160 190 190
240 209 285
123 147 147
127 151 151
139 165 165
171 204 204
154 183 183
2x95 (2x3/0) 2x95 (2x3/0)
315
2031 2559 2289
1828 2261 2051
0.98 0.98
0–590 0–590
110 (230) 110 (230)
75 (167) 75 (167)
± 15% (tolerance relates to variety in voltage and cable conditions). These
N160
NO HO NO
132 132 160
200 200 250
160 160 200
260 260 315
286 390 347
240 240 302
264 360 332
180 180 218
191 191 241
208 208 262
251 251 304
231 231 291
2x95 (2x3/0)
350 400
2954 2923 3770
2724 2089 3628
0.98
0–590
110 (230)
75 (167)
7 7
41