Danfoss VLT AQUA Drive FC 202 Design Manual page 214

How to Order a Drive
NEMA 3R outdoor weather
shield, D2h
NEMA 3R for in-back/out-back
cooling kit within a welded
enclosure, D3h
NEMA 3R for in-back/out-back
cooling kit within a Rittal
enclosure, D3h
NEMA 3R for in-back/out-back
cooling kit within a welded
enclosure, D4h
NEMA 3R for in-back/out-back
cooling kit within a Rittal
enclosure, D3h
Adaptor plate, D1h/D3h
Adaptor plate, D2h/D4h
Back-channel duct kit, D3h
Back-channel duct kit, D3h
Back-channel duct kit, D4h
Back-channel duct kit, D4h
Pedestal, D1h
Pedestal, D2h
13 13
Pedestal, D5h/D6h
Pedestal, D7h/D8h
Top entry of fieldbus cables,
D1h–D8h
USB in the door, D1h–D8h
(IP20/chassis)
USB in the door, D1h–D8h
(IP21/Type 1 and IP54/Type 12)
Input plate option, D1h–D8h
Terminal blocks
Back-channel cooling kits
212
®
VLT AQUA Drive FC 202
Shield designed to protect drive openings from direct sun, snow, and
falling debris. Drives using this shield must be ordered from the
factory as NEMA 3R ready, which is found in the type code as E5S
enclosure option.
Provides an ingress protection rating of NEMA 3R or NEMA 4. These
enclosures are intended for outdoor use to provide protection against
inclement weather.
Provides an ingress protection rating of NEMA 3R or NEMA 4. These
enclosures are intended for outdoor use to provide protection against
inclement weather.
Provides an ingress protection rating of NEMA 3R or NEMA 4. These
enclosures are intended for outdoor use to provide protection against
inclement weather.
Provides an ingress protection rating of NEMA 3R or NEMA 4. These
enclosures are intended for outdoor use to provide protection against
inclement weather.
Plate used to replace an enclosure D1/D3 with the D1h/D3h using the
same mounting configuration.
Plate used to replace an enclosure D2/D4 with the D2h/D4h using the
same mounting configuration.
Duct kit that converts enclosure to either in-bottom/out-top venting
or top only venting. Enclosure size: 1800 mm (70.9 in).
Duct kit that converts enclosure to either in-bottom/out-top venting
or top only venting. Enclosure size: 2000 mm (78.7 in).
Duct kit that converts enclosure to either in-bottom/out-top venting
or top only venting. Enclosure size: 1800 mm (70.9 in).
Duct kit that converts enclosure to either in-bottom/out-top venting
or top only venting. Enclosure size: 2000 mm (78.7 in).
Provides a 400 mm (15.7 in) pedestal that allows the drive to be floor
mounted. The front of the pedestal has openings for input air to cool
the power components.
Provides a 400 mm (15.7 in) pedestal that allows the drive to be floor
mounted. The front of the pedestal has openings for input air to cool
the power components.
Provides a 200 mm (7.9 in) pedestal that allows the drive to be floor
mounted. The front of the pedestal has openings for input air to cool
the power components.
Provides a 200 mm (7.9 in) pedestal that allows the drive to be floor
mounted. The front of the pedestal has openings for input air to cool
the power components.
Allows for the installation of fieldbus cables through the top of the
drive. The kit is IP20/chassis when installed, but a different mating
connector can be used to increase the protection rating.
USB extension cord kit to allow access to the drive controls via laptop
computer without opening the drive.
USB extension cord kit to allow access to the drive controls via laptop
computer without opening the drive.
Allows fuses, disconnect/fuses, RFI, FRI/fuses, and RFI/disconnect/fuses
options to be added.
Screw terminal blocks for replacing spring loaded terminals.
(1 pc 10 pin 1 pc 6 pin and 1 pc 3-pin connectors)
Danfoss A/S © 01/2018 All rights reserved.
176F6303
176F3521
176F3633
176F3526
176F3634
176F3409
176F3410
176F3627
176F3629
176F3628
176F3630
176F3631
176F3632
176F3452
176F3539
176F3594
Contact factory
Contact factory
Contact factory
130B1116
Standard Stainless steel
MG22B222