gefran ADV200 Series Quick Start Up Manual, Specification And Installation page 81

Step 2 - Setting motor parameter (Set motor data)
Set the rating data of the motor connected: rated voltage, rated frequency, rated
current, rated speed, rated power, power factor (cosφ).
The self-tuning procedure is described below using the data of an imaginary motor
by way of example.
T+ T - EN LOC ILim n:0 AL
01 MONITOR
02 DRIVE INFO
03 STARTUP WIZARD
04 DRIVE CONFIG
Rated Voltage [V]:
Rated current [A]:
Rated speed [rpm]:
Rated frequency [Hz]:
Pole pairs:
Motor & Co.
Type: ABCDE IEC 34-1 / VDE 0530
Motor: 3 phase Nr
50 Hz .
Rated voltage
380 V
I nom
Rated power
10 Hp Power factor
Rated speed (n ) 720 rpm
N
IP54
Iso Kl F S1
Made in ..............
T+ T- EN LOC ILim n:0 AL
STARTUP WIZARD
E
Set motor data ?
E=Yes Down=Next
motor rated voltage as indicated on the data plate.
motor rated current, approximately, the value should not be less than 0.3 times the rated current of the
drive, output current class 1 @ 400V on the rating plate of the drive.
motor rated speed, the value must reflect the speed of the motor at full load at rated frequency. If slip is
indicated on the motor rating data, set the Rated speed parameter as follows:
Rated speed = Synchronous speed - Slip
motor rated frequency, as shown on the data plate.
Number of motor pole pairs. The number of motor pole pairs is calculated using the data on the plate and
the following formula: P = 60 [s] x f [Hz] / nN [rpm]
Where: p = motor pole pairs
ADV200 • Quick start up guide
12345-91
19.0 A
0.83
T+ T- EN LOC ILim n:0 AL T+ T+
S E Q . 0 1 PA R : 2 0 0 0 1 3 . 0 1 S E Q . 0 1
E
Rated voltage Rated voltage Rated voltage
400
+ + +
V
Def: +400 Def: Def:
T+ T- EN LOC ILim n:0 AL T+
S E Q . 0 2 PA R : 2 0 0 2 S E Q . 0 2
E
Rated current Rated current
11.8
+ +
A
Def: +11.8 Def:
T+ T- EN LOC ILim n:0 AL T+
S E Q . 0 3 PA R : 2 0 0 4 S E Q . 0 3
E
Rated speed Rated speed
1450
+ +
rpm
Def: +1450 Def:
T+ T- EN LOC ILim n:0 AL
S E Q . 0 4 PA R : 2 0 0 6
Rated frequency
50.0
+
Hz
Def: +50.0
T+ T- EN LOC ILim n:0 AL T+
S E Q . 0 5 PA R : 2 0 0 8 S E Q . 0 5
E
Pole pairs Pole pairs
2
+ +
Def: +2 Def:
T+ T- EN LOC ILim n:0 AL T+
S E Q . 0 6 PA R : 2 0 1 0 S E Q . 0 6
E
Rated power Rated power
5.50
+ +
kW
Def: +5.50 Def:
T+ T- EN LOC ILim n:0 AL
S E Q . 0 7 PA R : 2 0 1 2
Rated power factor
0.83
+
Def: +0.83
T- T- EN EN LOC LOC ILim ILim n:0 n:0 AL AL T+
E
PA R : PA R : 2 0 0 0 1 0 0 S E Q . 0 1
Rated voltage
000000400 000000400 000000380
+
V V
+400 +400 Def:
T- EN LOC ILim n:0 AL T+
E
PA R : 2 0 0 2 S E Q . 0 2
Rated current
0000011.8 0000019.0
+
A
+11.8 Def:
T- EN LOC ILim n:0 AL T+
E
PA R : 2 0 0 4 S E Q . 0 3
Rated speed
000001450 000000720
+
rpm
+1450 Def:
T- EN LOC ILim n:0 AL T+
E
PA R : 2 0 0 8 S E Q . 0 5
Pole pairs
000000002 000000004
+
+2 Def:
T- EN LOC ILim n:0 AL T+
E
PA R : 2 0 1 0 S E Q . 0 6
Rated power
000005.50 000007.36
+
kW
+5.50 Def:
T- EN LOC ILim n:0 AL
PA R : 2 0 0 0
E
V
+400
T- EN LOC ILim n:0 AL
PA R : 2 0 0 2
E
A
+11.8
T- EN LOC ILim n:0 AL
PA R : 2 0 0 4
E
rpm
+1450
T- EN LOC ILim n:0 AL
PA R : 2 0 0 8
E
+2
T- EN LOC ILim n:0 AL
PA R : 2 0 1 0
E
kW
+5.50
81