Settings - Siemens SIPROTEC 4 Manual

Functions
2.15 Automatic Reclosing System 79
is available, active, unblocked and ready for another cycle. Control via the cold load pickup function is not
ARcycle- related.
Since control via cold load pickup and cyclic control via auto-reclosing system can run simultaneously, the
overcurrent protection must coordinate the input values of the two interfaces. In this context the cyclic auto-
reclosing control has the priority and thus overwrites the release of the cold load pickup function.
If the protective elements are controlled via the automatic reclosure function, changing the control variables
(e.g. by blocking) has no effect on elements that are already running. The elements in question are continued.
Note Regarding Settings List for Automatic Reclosure Function
The setting options of address 7137 Cmd.via control are generated dynamically according to the current
configuration.

Settings

2.15.7
Addr. Parameter
7101 FCT 79
7103 BLOCK MC Dur.
7105 TIME RESTRAINT
7108 SAFETY 79 ready
7113 CHECK CB?
7114 T-Start MONITOR
7115 CB TIME OUT
7116 Max. DEAD EXT.
7117 T-ACTION
7118 T DEAD DELAY
7127 DEADTIME 1: PH
7128 DEADTIME 1: G
7129 DEADTIME 2: PH
7130 DEADTIME 2: G
7131 DEADTIME 3: PH
7132 DEADTIME 3: G
7133 DEADTIME 4: PH
7134 DEADTIME 4: G
7135 # OF RECL. GND
7136 # OF RECL. PH
7137 Cmd.via control
7138 Internal SYNC
7139 External SYNC
7140 ZONE SEQ.COORD.
224
Setting Options
OFF
ON
0.50 .. 320.00 sec; 0
0.50 .. 320.00 sec
0.01 .. 320.00 sec
No check
Chk each cycle
0.01 .. 320.00 sec; ∞
0.10 .. 320.00 sec
0.50 .. 1800.00 sec; ∞
0.01 .. 320.00 sec; ∞
0.0 .. 1800.0 sec; ∞
0.01 .. 320.00 sec
0.01 .. 320.00 sec
0.01 .. 320.00 sec
0.01 .. 320.00 sec
0.01 .. 320.00 sec
0.01 .. 320.00 sec
0.01 .. 320.00 sec
0.01 .. 320.00 sec
0 .. 9
0 .. 9
(Einstellmöglichkeiten
anwendungsabhängig)
(Einstellmöglichkeiten
anwendungsabhängig)
YES
NO
OFF
ON
Default Setting Comments
OFF 79 Auto-Reclose Function
1.00 sec AR blocking duration after manual
close
3.00 sec 79 Auto Reclosing reset time
0.50 sec Safety Time until 79 is ready
No check Check circuit breaker before AR?
0.50 sec AR start-signal monitoring time
3.00 sec Circuit Breaker (CB) Supervision
Time
100.00 sec Maximum dead time extension
∞ sec Action time
1.0 sec Maximum Time Delay of Dead-
Time Start
0.50 sec Dead Time 1: Phase Fault
0.50 sec Dead Time 1: Ground Fault
0.50 sec Dead Time 2: Phase Fault
0.50 sec Dead Time 2: Ground Fault
0.50 sec Dead Time 3: Phase Fault
0.50 sec Dead Time 3: Ground Fault
0.50 sec Dead Time 4: Phase Fault
0.50 sec Dead Time 4: Ground Fault
1 Number of Reclosing Cycles
Ground
1 Number of Reclosing Cycles Phase
none Close command via control device
none Internal 25 synchronisation
NO External 25 synchronisation
OFF ZSC - Zone sequence coordination
E50417-G1140-C343-A8, Edition 12.2017
SIPROTEC 4, 7SJ80, Manual