Cisco ASA Series Cli Configuration Manual page 672

Configuring OSPFv3
Command
Step 1
ipv6 router ospf
process-id
Example:
hostname(config-if)# ipv6
router ospf 1
Step 2
redistribute
source-protocol
[process-id]
[include-connected
{[level-1 | level-2}]
[as-number] [metric
[metric-value |
transparent}]
[metric-type type-value]
[match {external [1|2] |
internal | nssa-external
[1|2]}] [tag tag-value]
[route-map map-tag]
Example:
hostname(config-rtr)#
redistribute connected 5
type-1
Cisco ASA Series CLI Configuration Guide
1-40
Purpose
Enables an OSPFv3 routing process and enters IPv6 router configuration mode.
The process-id argument is an internally used identifier for this routing process, is
locally assigned, and can be any positive integer from 1 to 65535. This ID does not
have to match the ID on any other device; it is for internal administrative use only.
You can use a maximum of two processes.
Redistributes IPv6 routes from one OSPFv3 process into another.
The source-protocol argument specifies the source protocol from which routes are
being redistributed, which can be static, connected, or OSPFv3. The process-id
argument is the number that is assigned administratively when the OSPFv3 routing
process is enabled. The include-connected keyword allows the target protocol to
redistribute routes learned by the source protocol and connected prefixes on those
interfaces over which the source protocol is running. The level-1 keyword specifies
that for Intermediate System-to-Intermediate System (IS-IS), Level 1 routes are
redistributed into other IP routing protocols independently. The level-1-2 keyword
specifies that for IS-IS, both Level 1 and Level 2 routes are redistributed into other
IP routing protocols. The level-2 keyword specifies that for IS-IS, Level 2 routes are
redistributed into other IP routing protocols independently. For the metric
metric-value keyword-argument pair, when redistributing routes from one OSPFv3
process into another OSPFv3 process on the same router, the metric is carried
through from one process to the other if no metric value is specified. When
redistributing other processes into an OSPFv3 process, the default metric is 20 when
no metric value is specified. The metric transparent keyword causes RIP to use the
routing table metric for redistributed routes as the RIP metric. The metric-type
type-value keyword-argument pair specifies the external link type that is associated
with the default route that is advertised into the OSPFv3 routing domain. Valid
values can be one of the following: 1 for a Type 1 external route or 2 for a Type 2
external route. If no value is specified for the metric-type keyword, the ASA adopts
a Type 2 external route. For IS-IS, the link type can be one of the following: internal
for an IS-IS metric that is less than 63 or external for an IS-IS metric that is greater
than 64 and less than 128. The default is internal. The match keyword redistributes
routes into other routing domains and is used with one of the following options:
external [1|2] for routes that are external to the autonomous system, but are
imported into OSPFv3 as Type 1 or Type 2 external routes; internal for routes that
are internal to a specific autonomous system; nssa-external [1|2] for routes that are
external to the autonomous system, but are imported into OSPFv3 in an NSSA for
IPv6 as Type 1 or Type 2 external routes. The tag tag-value keyword-argument pair
specifies the 32-bit decimal value that is attached to each external route, which may
be used to communicate information between ASBRs. If none is specified, then the
remote autonomous system number is used for routes from BGP and EGP. For other
protocols, zero is used. Valid values range from 0 to 4294967295. The route-map
keyword specifies the route map to check for filtering the importing of routes from
the source routing protocol to the current routing protocol. If this keyword is not
specified, all routes are redistributed. If this keyword is specified, but no route map
tags are listed, no routes are imported. The map-tag argument identifies a configured
route map.
Chapter 1 Configuring OSPF