Table of Contents
Advertisement
ASSEMBLY INSTRUCTIONS
Wing Coulter Chisel Center
Frame Assembly
Do not attempt to lift heavy parts (such as the
frame, coulter gangs, wheel lift, and pull hitch)
manually. Use a hoist or a forklift to move these
parts into position.
IMPORTANT
Read all safety precautions at the front of the section
before attempting any of the following procedures.
1. Place center frame assembly on stands
approximately 36" high. The assembly area should
be a large level area of sufficient size to
accommodate the Wing Coulter Chisel when fully
assembled.
Hitch Installation
1. Attach the hitch weldment to the front of the frame
using hitch pins, 1-8 hex lock nuts, and 1/2 x 2-1/4
slotted spring pins (See Figure 3-1.)
2. Move the jack to the forward mounting tube and
rotate to parking position to support the front of the
hitch.
3. Insert a 3/4-10 x 10-1/2 hex head cap screw into the
hose holder tube on the right side of the hitch from
the bottom side so the threads point upward. Hold in
place with a 3/4 prevailing torque flange nut with the
flange pointing upward as well. Do not tighten this
cap screw, so the hose holder bracket may pivot
freely in this joint.
4. Slide the hose holder bracket over the screw and
secure with another 3/4 prevailing torque flange nut.
3-4
WARNING
5. Install a 3/8-16 x 3-1/2 all-thread screw in the front of
the hose holder bracket and secure with a 3/8-16 hex
nut.
6. Slide the hose holder clamp over the 3/8" screw and
loosely start the wing nut on top of the clamp.
Hydraulic hoses will be routed through the clamp
after assembly.
IMPORTANT
The clamp has two sides, so that extend hoses can
be located on one side and retract hoses can be
located on the other side for reference.
IMPORTANT
The leveler tower must be installed so that the
narrow end of the tower is down and the reinforced
holes are to the rear of the machine.
7. Connect narrow end of the leveler tower to the top
hole of the hitch weldment using 1-1/4-7 x 9-1/2 hex
head cap screw, slotted lock washer, and hex nut.
8. Attach the leveler tube to leveler mount plates on the
lift using hitch pin, 1-8 hex lock nut, and 1/2 x 2-1/4
grooved alloy pin.
9. Insert 1-1/2 flange bearings in loose end of the
leveler tube.
10. Connect loose end of leveler tube to the rear top hole
of the leveler tower using hitch pin, 1-8 hex lock nut,
and 1/2 x 2-1/4 grooved alloy pin.
11. Attach the hitch rod radius assembly to the top front
hole of the leveler tower using 1-1/4-7 x 8 hex head
cap screw, slotted lock washer, and hex nut.
12. Connect the remaining end of the hitch rod radius
assembly to the hitch weldment using 1-1/4-7 x 8 hex
head cap screw, slotted lock washer, and hex nut.
13. Assemble hitch ring to the hitch weldment using 1-8 x
7-1/2 hex head cap screws, hitch bushings, flat
washer, and hex lock nuts through the top hole. Use
same hardware, safety chain assembly, and flat
washers in the lower hole.
14. Install optional hitch weights to hitch weldment using
3/4-10 hex head cap screws, height clamps, and hex
lock nuts. Use proper length screws in accordance
with number of hitch weights being used (See
Figure 3-2.)
NOTE
Hitch weights are required when equipment has chopper
reel or harrow assemblies attached to the rear. This will
help balance the machine and prevent it from tipping
over.
F-721-0513
Advertisement
Table of Contents
