Inverter Specifications; Class Specifications - Hitachi SJ Series User Manual

Chapter 20

20.2 Inverter Specifications

20.2.1 200V Class Specifications
Model symbol
P1-*****-L
ND capacity standard notation
P1-***L
Applicable motor (4-pole) capacity (kW)
Rated output current (A)
Overload current rating *1)
Rated output voltage
Output
200V
Rated capacity
(kVA)
240V
Rated input current (A) *2)
Input Rated input AC voltage *3)
Power supply equipment
capacity (kVA) *4)
Carrier frequency operating range *5)
Motor start torque*6)
Regenerative braking
Braking
Minimum resistance that can be
connected (Ω)
H (height) (mm)
Dimension
W (width) (mm)
*7)
D (depth) (mm)
Protective construction
Approximate mass (kg)
*1) The values shown are ratings when carrier frequency is at 2kHz. Please
use the inverter in accordance with "20.4 Current Derating Table".
*2) The rated input currents shown in the table are the values when the rated
current is output. The values vary depending on impedance on the
power supply (wiring, breaker, input reactor option, etc.)
*3) The following shows response to the Low Voltage Directive.
- Pollution degree 2
- Overvoltage category 3
*4) The power supply equipment capacities shown in the table are the
values when 220V rated current is output. The values vary depending on
impedance on the power supply (wiring, breaker, input reactor option,
etc.)
*5) The setting of rated values for carrier frequencies [bb101]/[bb201] are
internally limited in accordance with the description. Also, it is
recommended to set values equivalent to or above (maximum output
frequency for driving ×10) Hz for the setting of carrier frequencies
[bb101]/[bb201]. Also, in the case of induction motor (IM) control, for
items other than those subject to V/f control, it is recommended to set
carrier frequency at 2kHz or more. In the case of synchronous motor
(SM)/permanent magnet motor (PMM) control, it is recommended to set
carrier frequency at 8kHz or more.
00044 00080 00104 00156 00228 00330 00460 00600 00800 00930 01240 01530 01850 02290 02950
004 007 015 022
VLD 0.75 1.5 2.2 3.7
0.75 1.5 2.2 3.7
LD
0.4 0.75 1.5 2.2
ND
VLD 4.4 8.0 10.4 15.6
LD 3.7 6.3 9.4 12.0
ND 3.2 5.0 8.0 11.0
VLD
LD
ND
3-phase (3-wire) 200-240V (depending on receiving voltage)
VLD 1.5 2.8 3.6 5.4
LD
1.3 2.2 3.3 4.2
ND
1.1 1.7 2.8 3.8
VLD 1.8 3.3 4.3 6.5
LD 1.5 2.6 3.9 5.0
ND 1.3 2.1 3.3 4.6
VLD 5.2 9.5 12.4 18.6
LD 4.4 7.5 11.2 14.3
ND 3.8 6.0 9.5 13.1
Control power supply: Power supply single phase 200-240V/allowable variation range 170-264V,
50Hz (allowable variation range: 47.5~52.5Hz)/60Hz (allowable variation range: 57-63Hz)
Main circuit power supply: 3-phase (3-wire) 200-240V/allowable variation range 170-264V,
50Hz (allowable variation range: 47.5-52.5Hz)/60Hz (allowable variation range: 57-63Hz)
2.0 3.6 4.7 7.1
VLD
1.7 2.9 4.3 5.4
LD
1.5 2.3 3.6 5.0
ND
VLD
LD
ND
Equipped with BRD circuit (with a discharging resistor separately installed)
50 50 35 35
255 255 255 255
150 150 150 150
140 140 140 140
3 3 3 3
20-2
* The models in 200V class are shown as P1-*****-LFF or
P1-*****-LFUF. The portion "*****" are filled with numbers
described in "Model symbol".
037 055 075 110 150
5.5 7.5 11 15 18.5
5.5 7.5 11 15 18.5
3.7 5.5 7.5 11 15
22.8 33.0 46.0 60.0 80.0
19.6 30.0 40.0 56.0 73.0
17.5 25.0 32.0 46.0 64.0
110% 60sec / 120% 3sec
120% 60sec / 150% 3sec
150% 60sec / 200% 3sec
7.9 11.4 15.9 20.8 27.7
6.8 10.4 13.9 19.4 25.3
6.1 8.7 11.1 15.9 22.2
9.5 13.7 19.1 24.9 33.3
8.1 12.5 16.6 23.3 30.3
7.3 10.4 13.3 19.1 26.6
27.1 39.3 54.8 71.4 95.2
23.3 35.7 47.6 66.7 86.9 101.2 134.5 166.7 201.2 250.0 321.4
20.8 29.8 38.1 54.8 76.2
10.3 15.0 20.9 27.2 36.3
8.9 13.6 18.1 25.4 33.1
7.9 11.3 14.5 20.9 29.0
0.5~10.0kHz
0.5~12.0kHz
0.5~16.0kHz
200%/0.3Hz
35 16 10 10 7.5
255 260 260 260 390
150 210 210 210 245
140 170 170 170 190
IP20 / UL open type
3 7 7 7 16
*6) Values when sensorless vector control is applied at ND rating on a
Hitachi's standard motor. Torque characteristics may be different
depending on the control method or motor for use.
*7) The dimensions do not include buttons on the operator keypad.
When optional items are connected, the required dimensions will
increase. Check the instruction manuals of each optional item for details.
Specifications
185 220 300 370 450
22 30 37 45 55
22 30 37 45 55
18.5 22 30 37 45
93.0 124 153 185 229
85.0 113 140 169 210
76.0 95.0 122 146 182
79.3 102.2
32.2 43.0 53.0 64.1
29.4 39.1 48.5 58.5 72.7
26.3 32.9 42.3 50.6 63.0
95.2 122.6
38.7 51.5 63.6 76.9
87.3 112.2
35.3 47.0 58.2 70.3
31.6 39.5 50.7 60.7 75.7
110.7 147.6 182.1 220.2 272.6 351.2
90.5 113.1 145.2 173.8 216.7 261.9
42.2 56.3 69.4 83.9 103.9 133.8
38.6 51.3 63.5 76.7 95.3 122.5
34.5 43.1 55.3 66.2 82.6
Regenerative braking unit
separately installed
7.5 5 - - -
550 550
390 390 540
390 390
245 245 300
250 250
190 190 195
16 16 22 30 30
550
75
75
55
295
270
220
93.5
76.2
91.5
99.8
-
700
480
250
43