Hitachi SJ Series User Manual page 653

Chapter 20
20.2.2 400V Class Specifications
Model symbol
P1-*****-H
ND capacity standard notation
P1-***H
Applicable motor (4-pole)
capacity (kW)
Rated output
current (A)
Overload current
rating
Output Rated output voltage
400V
Rated
capacity
(kVA)
500V
Rated input current
(A) *1)
Input Rated input AC voltage *2)
Power supply
equipment capacity
(kVA) *3)
Carrier frequency range *4)
Motor start torque*5)
Regenerative braking
Braking
Minimum resistance that
can be connected (Ω)
H (height) (mm)
Dimension
W (width) (mm)
*7)
D (depth) (mm)
Protective construction
Approximate mass (kg)
*1) The values shown are ratings when carrier frequency is at 2kHz. Please
use the inverter in accordance with "20.4 Current Derating Table".
*2) The rated input currents shown in the table are the values when the rated
current is output. The values vary depending on impedance on the
power supply (wiring, breaker, input reactor option, etc.)
*3) The following shows response to the Low Voltage Directive.
- Pollution degree 2
- Overvoltage category 3 (when input voltage is between 380 and 460
VAC)
- Overvoltage category 2 (when input voltage is higher than 460 VAC)
*4) The power supply equipment capacities shown in the table are the
values when 440V rated current is output. The values vary depending on
impedance on the power supply (wiring, breaker, input reactor option,
etc.)
*5) The setting of rated values for carrier frequencies [bb101]/[bb201] are
internally limited in accordance with the description. Also, it is
recommended to set values equivalent to or above (maximum output
frequency for driving ×10) Hz for the setting of carrier frequencies
[bb101]/[bb201]. Also, in the case of induction motor (IM) control, for
items other than those subject to V/f control, it is recommended to set
carrier frequency at 2kHz or more. In the case of synchronous motor
(SM)/permanent magnet motor (PMM) control, it is recommended to set
carrier frequency at 8kHz or more.
00041 00054 00083 00126 00175 00250 00310 00400 00470 00620 00770 00930 01160 01470 01760 02130 02520 03160
007 015 022 037 055
1.5 2.2 3.7 5.5 7.5
VLD
LD 1.5 2.2 3.7 5.5 7.5
ND 0.75 1.5 2.2 3.7 5.5
4.1 5.4 8.3 12.6 17.5 25.0 31.0 40.0 47.0 62.0 77.0 93.0
VLD
3.1 4.8 6.7 11.1 16.0 22.0 29.0 37.0 43.0 57.0 70.0 85.0
LD
2.5 4.0 5.5 9.2 14.8 19.0 25.0 32.0 39.0 48.0 61.0 75.0 91.0
ND
VLD
LD
ND
2.8 3.7 5.8 8.7 12.1 17.3 21.5 27.7 32.6 43.0 53.3 64.4 80.4 101.8 121.9 147.6 174.6 218.9
VLD
2.1 3.3 4.6 7.7 11.1 15.2 20.1 25.6 29.8 39.5 48.5 58.9 72.7 93.5 110.9 135.1 159.3 200.9
LD
1.7 2.8 3.8 6.4 10.3 13.2 17.3 22.2 27.0 33.3 42.3 52.0 63.0 77.6 103.9 124.7 150.3 180.1
ND
3.6 4.7 7.2 10.9 15.2 21.7 26.8 34.6 40.7 53.7 66.7 80.5 100.5 127.3 152.4 184.5 218.2 273.7
VLD
2.7 4.2 5.8 9.6 13.9 19.1 25.1 32.0 37.2 49.4 60.6 73.6 90.9 116.9 138.6 168.9 199.2 251.1
LD
2.2 3.5 4.8 8.0 12.8 16.5 21.7 27.7 33.8 41.6 52.8 65.0 78.8 97.0 129.9 155.9 187.9 225.2
ND
VLD
4.9 6.4 9.9 15.0 20.8 29.8 36.9 47.6 56.0 73.8 91.7 110.7 138.1 175.0 209.5 253.6 300.0 376.2
LD 3.7 5.7 8.0 13.2 19.0 26.2 34.5 44.0 51.2 67.9 83.3 101.2 125.0 160.7 190.5 232.1 273.8 345.2
ND 3.0 4.8 6.5 11.0 17.6 22.6 29.8 38.1 46.4 57.1 72.6 89.3 108.3 133.3 178.6 214.3 258.3 309.5
Control power supply: Power supply single phase 380-500V (allowable variation range 323-550V),
50Hz (allowable variation range: 47.5-52.5Hz)/60Hz (allowable variation range: 57-63Hz)
Main circuit power supply: 3-phase (3-wire) 380-500V (allowable variation range) 323-550V,
50Hz (allowable variation range: 47.5-52.5Hz)/60Hz (allowable variation range: 57-63Hz)
3.7 4.9 7.5 11.4 15.9 22.7 28.1 36.3 42.6 56.3 69.9 84.4 105.2 133.4 159.7 193.2 228.6 286.7
VLD
2.8 4.4 6.1 10.1 14.5 20.0 26.3 33.6 39.0 51.7 63.5 77.1 95.3 122.5 145.2 176.9 208.7 263.1
LD
2.3 3.6 5.0 8.3 13.4 17.2 22.7 29.0 35.4 43.5 55.3 68.0 82.6 101.6 136.1 163.3 196.9 235.9
ND
VLD
LD
ND
Equipped with braking resistance circuit
(with a discharging resistor separately installed)
100 100 100 70
255 255 255 255 260
150 150 150 150 210
140 140 140 140 170
3 3 3 3
* The models in 400V class are shown as P1-*****-HFF or
P1-*****-HFEF, P1-*****-HFUF, or P1-*****-HFCF.***** filled with
numbers described in "Model symbol".
075 110 150 185 220
11 15 18.5 22 30
11 15 18.5 22 30
7.5 11 15 18.5 22
110% 60sec / 120% 3sec
120% 60sec / 150% 3sec
150% 60sec / 200% 3sec
3-phase (3-wire) 380-500V (depending on receiving voltage)
0.5~10.0kHz
0.5~12.0kHz
0.5~16.0kHz
200%/0.3Hz
70 35 35 24 24 20
260 260 390 390 390
210 210 245 245 245
170 170 190 190 190
IP20 / UL open type
7 7 7 16 16 16
*6) Values when sensorless vector control is applied at ND rating on a
Hitachi's standard motor. Torque characteristics may be different
depending on the control method or motor for use.
*7) The dimensions do not include buttons on the operator keypad.
When optional items are connected, the required dimensions will
increase. Check the instruction manuals of each optional item for details.
*8) Usually a regenerative braking unit needs to e separately installed,
however, in response to your order, we can install the braking circuit
internally and attach a discharging resistor, thereby eliminating the need
for the regenerative braking unit. Please contact the sales officer of our
company shown in the back cover.
20-3
Specifications
300 370 450 550 750 900 1100 1320
37 45 55 75 90 110
37 45 55 75 90 110
30 37 45 55 75 90
116 147 176 213
105 135 160 195
112 150 180
0.5~8.0kHz
0.5~8.0kHz
0.5~10.0kHz
180%/0.3Hz
*6) Regenerative braking unit
separately installed
15 10 10
15 -
550 550 550 700 700
540
390 390 390 390 390
300
250 250 250 270 270
195
22 30 30 30 55 55
132 160
132 160
110 132
252 316
230 290
217 260
- - -
740 740
480 480
270 270
70 70