Menu Configuration And Content - Ikegami HDK-55 Operation Manual

Menu Configuration and content
The following lists the camera menu configuration.
MENU (Simple Menu)
■
The simple menu is the same as MENU (1/3) described below. Refer to items in MENU (1/3) for details of each menu.
■ MENU (1/3)
Menu Item
VF DISPLAY
DISPLAY MODE
MARKER/CHAR LVL
FRAME MARKER
VF ASPECT
SIDE MASK
CONTRAST
BRIGHT
SAFETY AREA
SAFETY MARKER
CENTER MARKER
FOCUS INDICATE
ZOOM INDICATE
AUTO VF ASPECT
ZEBRA INDICATOR
ZEBRA1 DETECT
ZEBRA2 IND
ZEBRA2 DETECT
ZEBRA IND LVL
VF DTL
BOOST FREQ
NOISE SUP
VF DTL
VF MODE
COLOR VF MODE
VF VIDEO SELECT
FRONT TALLY
*1 : It is possible to determine when loading MENU DATA from the SD CARD whether to read the entire MENU or to read only items related to VF.
The setting of an item having a checkmark is read.
*2 : If the color VF is recognized automatically, the display switches to R/G/B.
Initial
Setting value
setting
2 OFF, 1, 2
100 1 to 100
ON-16:9, ON-14:9, ON-13:9,
OFF
ON-4:3, OFF
16:9 16:9, 4:3
OFF, ON-4:3,
OFF
ON-13:9, ON-16:9
50 0 to 100
60 0 to 100
ACTION ACTION, TITLE
ON-16:9 ON-4:3, ON-16:9, OFF
ON ON, OFF
ON OFF, ON
ON OFF, ON
OFF ON, OFF
100% 30 to 109%
OFF OFF, ON
70% 30 to 109%
78 1 to 100
10MHz,15MHz,
10MHz
18MHz,18MHzWIDE
5 0 to 10
35 0 to 100
AUTO AUTO, ON
Y Y, R, G, B, R+G+B,
(R/G/B) (R/G/B)
* 2
ENABLE ENABLE, DISABLE
HDK-55 1206 VER1 (U)
5.2 Settings from the Menu
Description, Remarks
OFF : The markers and characters are constantly OFF, and
only the warning messages are displayed.
1 : Only the markers are constantly displayed. Information
related to characters is displayed for 2 seconds during
function operation and when changing parameters.
2 : The markers and characters are displayed at all times.
Sets the brightness levels of the markers and characters. The
brightness level gets dark in the direction of "1".
Sets the frame marker.
Sets the VF aspect ratio.
Sets the side mask.
Adjusts the side mask contrast level.
Adjusts the side mask brightness level.
ACTION ： Area marker of 93% of the screen height and width.
TITLE ： Area marker of 89% of the screen height and width.
Sets the safety marker.
Sets the center marker.
Only active when using the serial lens.
Only active when using the serial lens.
Switches the VF aspect ratio in linked motion with the output
mode of the BS/CCU down converter.
Overlaps the striped pattern signal on the image if the image
level has exceeded the individual DETECT LEVELS.
The zebra indicator goes ON/OFF with the VF special switch.
-Zebra 1 signal ： Fine, slanted striped pattern signal flowing
toward the upper right of the screen.
Use to control the tone of the entire screen.
-Zebra 2 signal ： Thick, slanted striped pattern signal flowing
to the lower right of the screen.
Used for controlling the tone of the subject,
such as face tone, etc
Sets the DETECT LEVEL of the 1st zebra indicator.
Selects whether there is a 2nd zebra indicator or not.
Sets the DETECT LEVEL of the 2nd zebra indicator.
Adjusts the overlap level of the zebra indicator.
Adjusts the overlap amount of the VF image focusing edge
signal (VF DTL).
Selects the frequency to be boosted.
Sets the removal level of the noise signal.
Sets the VF detail amount. The detail amount decreases in the
direction of "0" and increases in the direction of "100".
AUTO : Automatically recognizes the color VF to convert the
VF VIDEO signal to R/G/B output.
ON : Makes the VF VIDEO signal output R/G/B.
Sets the VF image output.
R/G/B can be set in case the color VF is mounted or when the
COLOR VF MODE is ON.
Sets active/inactive for VF FRONT TALLY.
*1
MENU DATA
ALL VF
5
83