Ikegami HDK-55 Operation Manual page 104

5.2 Settings from the Menu
Menu Item
LENS TYPE
AUTO x0.8 CONV
X0.8 CONV CONT
LENS SERIAL I/F
LEVEL ADJUST
MASTER GAMMA
MASTER PED
MASTER FLARE
DTL GAIN
ADJ CLR
PROCESS MODE
SMOOTH STEP GAIN
SMOOTH STEP ECC
MATRIX
HI-LIGHT DTL
GAIN
LIMIT
SMOOTH KNEE
DTL V FILTER
PRESET FILE LOAD
FILE SELECT
LOAD START
MENU MODE
ENGINEER MENU
88
Initial
Setting Value
Setting
OFF, C.PORTABLE,
C.STUDIO, C.FIELD,
OFF
F.PORTABLE, F.STUDIO,
F.FIELD
OFF OFF, ON
OFF OFF, ON
ON ON, OFF
0.0 -100 to +100
0.0 -100 to +100
0.0 -100 to +100
0.0 -100 to +100
READY,
READY PUSH SET→CLR,
CANCEL
OFF,
ON-0.3s, ON-0.5s, ON-
ON-0.5s
0.7s, ON-1.0s, ON-1.5s,
ON-2.0s
OFF,
ON-0.3s, ON-0.5s, ON-
ON-0.5s
0.7s, ON-1.0s, ON-1.5s,
ON-2.0s
OFF OFF, 1, 2, 3
ON OFF, ON
0.0 1 to 100
0.0 -100 to +100
OFF, TYPE1,
TYPE-1
TYPE2, TYPE3
OFF ON, OFF
ENGINEER ENGINEER, FACTORY
READY READY, START, CANCEL Executes initialization.
OFF OFF, ON
HDK-55 1206 VER1 (U)
Description, Remarks
To match the zoom tracking DTL operation characteristics
with the lens zoom characteristics, set the time of the lens used
in the camera.
OFF ： Game tracking DTL is OFF.
C.PORTABLE ： Canon portable lens
C.STUDIO ： Canon studio lens
C.FIELD ： Canon field lens
F.PORTABLE ： Fujinon portable lens
F.STUDIO ： Fujinon studio lens
F.FIELD ： Fujinon field lens
Set by lens file (NO.1-8).
Set automatic switching of the aspect ratio converter (X0.8)
internal lens.
If set to ON, it operates in linked motion with the output aspect
ratio of the down converter to carry out automatic switching.
If turned ON when using the X0.8 converter internal lens,
control is possible.
When not using the X0.8 converter internal lens, set to OFF.
Set whether to respond to the serial interface of the lens or not.
Sets the master gamma value.
The gamma value decreases in the direction of " -100" and
increases in the direction of "+100".
Sets the master pedestal value.
The pedestal value decreases in the direction of "-100" and
increases in the direction of "+100".
Sets the master flare value.
The flare value decreases in the direction of "-100" and
increases in the direction of "+100".
Sets the detail amount.
The detail amount decreases in the direction of "-100" and
increases in the direction of "+100".
Returns the settings changed with LEVEL ADJUST to the state
prior to change as a group.
Changes the STEP GAIN step by step.
Possible to choose the time until convergence.
Changes the STEP ECC step by step.
Possible to choose the time until convergence.
There are independent settings for three channels of the matrix,
which can be switched.
Possible to increase the DTL level of the highlight part.
Sets the level value to be emphasized.
Level increases in the direction of +100.
Sets the upper limit for the emphasized DTD level.
The "-100" direction lowers the limit. The "+100" direction
raises the limit and lowers the DTL level.
SMOOTH KNEE is a function to adjust the compression level
of the brightness signal with KNEE. It can be selected from the
following three setting types.
TYPE1 : The compression rate of brightness is low.
TYPE2 : The compression rate of brightness is medium.
TYPE3 : The compression rate of brightness is high.
If the V filter of the DTL is ON, the resolution feeling in
direction V diminishes, making it possible to obtain an image
with less noise.
Function to load the user settings (ENGINEER SET FILE)
or factory settings (FACTORY SET FILE) for the level
adjustment or menu of the camera.
Used to return the camera state back to the previous or initial
settings.
ENGINEER : Initializes the state back to the user setting.
FACTORY : Initializes the state back to the initial factory
setting.
If set to ON, possible to display engineer menu.
If the camera power is turned OFF, this menu setting returns to
OFF.
MENU DATA
ALL VF
-
-
-
-
- -
- -
- -
- -
- -
-
-
- -
- -
- -
- -
- -
-
- -
- -
- -