Ikegami HDK-55 Operation Manual page 112

5.3 Using the Memory Card
■ Storing the camera setting state on the memory card
Store the camera setting state on the memory card. First confirm that the write protect switch of the memory card is not on the
LOCK side.
1
Turn the rotary pulse switch on MENU (2/3),
the cursor to [MEMORY CARD] and press the SET
button.
The submenu is displayed.
2
Select [SAVE FILE] and press the SET button.
The SAVE FILE submenu is displayed.
3
Select the item from the SAVE FILE submenu
that you wish to save.
Select ALL DATA on the picture.
4
After selecting the item you wish to save, press
the SET button. Then use the rotary pulse switch
and SET button to insert an eight-character file
name.
When the eight character file name has been
determined, [PUSH SET -> START] is displayed
on the cursor.
Press the SET button.If a file of the same file
name exists on the memory card at this time,
proceed to step M1. If you wish to cancel, turn the
rotary pulse switch when [PUSH SET -> START]
is displayed.
5
When the file is being saved, [SAVING FILE] is displayed.
If the file is saved normally, [COMPLETE] is displayed.
CAUTION:
Never remove the memory card from the slot during display of [SAVING FILE] or while the access indicator is lighted, as
data is being written to the memory card. Removing it at this time could damage the memory card data or the memory card
itself.
M1
If a file with the same file name exists on the
memory card, a message is displayed asking
whether it is all right to write over the data. To
enable writing over of data, change [NO] to [YES]
and press the SET button. If [NO] has been
selected, storage is cancelled and the system
returns to step [3].
96
set
ＭＥＭＯＲＹ ＣＡＲＤ
ＳＡＶＥ ＦＩＬＥ
ＬＯＡＤ ＦＩＬＥ
ＳＡＶＥ ＦＩＬＥ
ＡＬＬ ＤＡＴＡ
ＳＮＡＰ ＳＨＯＴ
ＳＣＥＮＥ
ＲＥＦＥＲＥＮＣＥ
ＬＥＮＳ
ＭＥＮＵ ＤＡＴＡ
ＳＡＶＥ ＦＩＬＥ
ＡＬＬ ＤＡＴＡ
ＳＮＡＰ ＳＨＯＴ
ＳＣＥＮＥ
ＲＥＦＥＲＥＮＣＥ
ＬＥＮＳ
ＭＥＮＵ ＤＡＴＡ
ＰＵＳＨ ＳＥＴ→ＳＴＡＲＴ
ＳＡＶＥ ＦＩＬＥ
ＡＬＬ ＤＡＴＡ
ＳＮＡＰ ＳＨＯＴ
ＳＣＥＮＥ
ＲＥＦＥＲＥＮＣＥ
ＬＥＮＳ
ＭＥＮＵ ＤＡＴＡ
ＯＶＥＲＬＡＰＰＥＤ ＦＩＬＥ ＮＡＭＥ .
ＯＶＥＲＷＲＩＴＥ ＮＯ
HDK-55 1206 VER1 (U)
ＡＢＣＤＥＦＧＨ .ＣＤＦ
ＡＢＣＤＥＦＧＨ .ＣＤＦ