Ikegami HDK-55 Operation Manual page 100

5.2 Settings from the Menu
Menu Item
FOCUS ASSIST
ASSIST AREA
TRIGGER
AREA ON/OFF SW
VF DOT BY DOT
FOR RET
ASSIST DATA
ASSIST DATA SETTING
SW ACTION
AREA DISP TIME
AREA SIZE
AREA LEVEL
AREA COLOR
AREA MARKER
EDGE BOOST
LEVEL
EDGE COLOR
STORE DATA
MIC GAIN CONTROL
MIC1 STEP
MIC1 FINE
MIC2 STEP
MIC2 FINE
RETURN SELECT MODE
RET-2/MIC SEL
VTR SW SEL
RET PRIORITY
FILTER SERVO MODE
SERVO CONT
SW FUNCTION
RET-1 (HANDLE)
RET-2 (HANDLE)
ZOOM SPEED
FOCUS SPEED
84
Initial
Setting value
setting
TRIGGER TRIGGER ON,
ON ALWAYS ON, OFF
FOCUS, FOCUS/ZOOM,
FOCUS
LENS VTR
NONE LENS VTR, NONE
UNLINK UNLINK, LINK
ON ON, OFF
NO.1 N0.1 to N0.4
ALTERNATE,
ALTERNATE
MOMENTARY
0.0S to 5.0S
1.0S
(units of 0.5 sec)
15 1 to 100
60% 100% to 25%
MONO MONO, COLOR, NEGA
OFF ON, OFF
55 1 to 100
MONO, CYAN,
MONO MAGENTA, YELLOW,
GREEN, RED, BLUE
--- N0.1 to N0.4
+4dB, 0dB, -10dB,
-40dB -20dB, -30dB, -40dB,
-50dB, -60dB
0 -100 to 100
+4dB, 0dB, -10dB,
-40dB -20dB, -30dB, -40dB,
-50dB, -60dB
0 -100 to 100
RET-2 RET-2, MIC
RET-2 RET-2, MIC
NOTHING,
NOTHING
RET-2, RET-1
SERVO SERVO ,MANUAL
RET-1, ZOOM-,
RET-1
FOCUS-, NONE
RET-2, ZOOM+, FOCUS+,
RET-2
NONE
15 0 to 100
15 0 to 100
HDK-55 1206 VER1 (U)
Description, Remarks
Sets the ASSIST AREA display.
Select TRIGGER ON if you wish to display with the trigger of
lens operation, etc.
Trigger to display ASSIST AREA.
This setting is used when TRIGGER ON is selected.
Selects the switch to turn ON/OFF the ASSIST AREA.
Sets whether a control signal is sent to a VF having a DOT BY
DOT display function.
Sets whether to display the ASSIST AREA or not when
switching to the RET signal.
Selects the ASSIST DATA compiled in the ASSIST DATA
SETTING menu.
If the trigger has been assigned to the LENS VTR SW, sets
whether it is momentary operation or alternate operation.
Sets the time from trigger detection until the focus assist area
is erased.
Sets the focus assist area range.
If set to "100", it is the entire screen domain.
Sets the image level of the ASSIST AREA.
Sets whether the ASSIST AREA image should be color,
monochrome or negative.
Sets whether the assist area frame marker is displayed nor not.
Sets the boost level of the edge signal.
Sets the color of the edge signal.
The contents set in the ASSIST DATA SETTING menu are
stored as ASSIST DATA. Select the numbers you wish to store
from No. 1 to No. 4 and write over the present data to store
them.
The MIC1 gain is changed step by step.
Fine adjustment of the MIC1 gain. The gain decreases about -8
dB with -100, and increases about +8 dB with +100.
The MIC2 gain is changed stepwise.
Fine adjustment of the MIC2 gain. The gain decreases about -8
dB with -100, and increases about +8 dB with +100.
Allocates a function to the RET-2/MIC button on top of handle
and on left side of camera.
If the FOCUS ASSIST menu (TRIGGER or AREA ON/OFF
SW) is set to LENS VTR, it becomes FOCUS ASST fixed
(information display).
If a RET-1 or RET-2 image is not displayed in the viewfinder,
sets the output signal to MON SDI (during RETURN setting).
NOTHING ： Sets to RET image last displayed in VF.
RET1 ： Sets to RET-1 image.
RET2 ： Sets to RET-2 image.
SERVO ： Sets to automatic control.
MANUAL ： Sets to manual control.
Sets the button control of RET-1 and RET-2/MIC on the top of
the handle.
When assigning to ZOOM, FOCUS, a serial lens is required.
Sets the operational speed of ZOOM, FOCUS control. The
speed is slower for "0" and faster for "100".
MENU DATA
ALL VF
- -
- -
- -
- -
- -
- -
‐ ‐
-
-
-
-
-
-
-
-
-
-
-
-