Initializing The Settings Of This Product - Ikegami HDK-55 Operation Manual

6.3 Initializing the Settings of this Product

The following two cases are available for initializing the setting of this product.
① Initializes the camera back to the user setting (ENGINEER SET FILE).
This initializes the camera back to the state set by user engineer in advance in response to the environment and the shooting
conditions.
② Initializes the camera back to the initial factory setting (FACTORY SET FILE)
This initializes the camera back to the initial factory setting.
To change the settings, select "PRESET FILE LOAD" on MENU (3/3), then "FILE SELECT" and "LOAD START."
The following explains the set values, descriptions, and setting procedures.
Set Value
FILE SELECT ENGINEER (default)
FACTORY
LOAD START READY (default)
START
CANCEL
1
On MENU (3/3), turn the rotary pulse switch to
position the cursor on "PRESET FILE LOAD", and
press the SET button.
The submenu is displayed.
2
Turn the rotary pulse switch to position the cursor
on "FILE SELECT", and press the SET button.
The cursor moves to the mode selection column.
3
Turn the rotary pulse switch to select the value to
be set, and press the SET button.
The value is confirmed.
4
Press the SET button when the cursor
automatically moves to "LOAD START".
The cursor moves to the mode selection column and
its display changes from "READY" to "START".
Initializes the state back to the user setting.
Initializes the state back to the initial factory setting.
The state before initialization
Starts initialization.
Cancels initialization.
ＳＣＡＮ ＦＯＲＭＡＴ ＳＥＬＥＣＴ
ＣＰＵ ＳＹＳＴＥＭ ＣＯＮＴＲＯＬ
ＡＵＴＯ ＩＲＩＳ ＳＥＴ
ＡＵＴＯ ＳＥＴＵＰ ＭＯＤＥ
ＬＥＮＳ ＳＥＬＥＣＴ
ＬＥＶＥＬ ＡＤＪＵＳＴ
ＰＲＯＣＥＳＳ ＭＯＤＥ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＦＩＬＥ ＳＥＬＥＣＴ ＥＮＧＩＮＥＥＲ
ＬＯＡＤ ＳＴＡＲＴ ＲＥＡＤＹ
ＦＩＬＥ ＳＥＬＥＣＴ ＥＮＧＩＮＥＥＲ
ＬＯＡＤ ＳＴＡＲＴ ＲＥＡＤＹ
ＦＩＬＥ ＳＥＬＥＣＴ ＥＮＧＩＮＥＥＲ
ＬＯＡＤ ＳＴＡＲＴ ＲＥＡＤＹ
HDK-55 1206 VER1 (U)
6.3 Initializing the Settings of this Product
Description
＊＊＊ ＭＥＮＵ （３／３） ＊＊＊
▲
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
6
①
Position the cursor on
"PRESET FILE LOAD"
and confirm.
②
Position the cursor on
"FILE SELECT" and
confirm.
③
Select "ENGINEER"
or "FACTORY" and
confirm.
④
Position the cursor on
"LOAD START" and
confirm.
103