Parts List Introduction - Xerox Telecopier 7017 Technical Reference Manual

Parts List Introduction

Overview
The Parts List section gives parts lists and
illustrations of spared subsystem components.
It gives information needed to order parts
used on the system as well as to repair and
replace them.
Organization
Section contents gives page references for all
subsections in the parts list.
Parts Lists (PL)
Each PL gives parts numbers of spared
subsystem components. Item numbers are
given in the parts lists
components on the exploded views.
Exploded Views
Exploded illustrations of spared subsystem
components are included with
Components on the illustrations are given
item numbers. Hardware items are lettered.
Item numbers on the illustration are the same
as item numbers on the PL. Refer to Common
Hardware to identify hardware.
Assemblies and kits are a combination of
several separate components.
identified on the illustration with the Part
Listing item number followed by illustration
numbers that make up the assembly.
example: "15 {5, 6, and 10."
Electrical Connectors
The last PL contains illustrations of electrical
connectors and a corresponding parts list.
Parts List Introduction
Common Hardware
This subsection identifies common hardware
used in the system. The hardware is listed in
alphabetical order by the item letter.
letters are used on the exploded views to
designate hardware in this list. All dimensions
are in millimeters unless otherwise noted.
Part Number Index
This subsection lists, by number, all the spared
parts in the system. It gives PL references for
the parts list of each spared part.
General Information
Symbols
Within the illustrations, and in the listings,
to reference
various symbols
Introduction, Symbology for definitions.
The asterisk * appears in the parts listing and
applies to Xerox USO and RX distribution. The
asterisk indicates that the part can be ordered
each PL.
only through
(USO) or CSO (RX).
Abbreviations
Abbreviations which may be used in the parts
lists text or illustrations are as follows:
These are
USO United States Operations
For
P/OTag/MOD
PWB
Item
are used. Refer
Telecopier Product Support
A AMP
FX Fuji Xerox
P/J Plug/Jack
P/O Part of
Part of Tag/MOD
OLV USO Olivetti FX 1500
Printed Wiring Board
RX Rank Xerox
12/88
5-2
www.printcopy.info
Tag/MOD Tag/Modification
V Volt
W Watt
W/ With
W/Tag/MOD With Tag/Modification
W/O Without
W/O Tag/MOD Without Tag/Modification
XCI Xerox Canada Inc.
XLA Xerox Latin America Group
Tag/MODs
A Tag/MOD is used when a part or area of the
system has been modified.
Tag/MOD Index, which is found in the General
Procedures/Information Section, lists the name
and purpose of the Tag/MOD. In some cases,
you will go to the parts lists and find a part
number listed as "with Tag/MOD."
to
Change Tag/MOD Index for a description of
what the Tag/MOD is and what you need to
install the Tag/MOD. The Change Tag/MOD
Index will either list a kit number (600K...) or
indicate "piece part."
indicated, the parts lists reference(s) will be
given and all parts
Tag/MOD will have to be individually located,
ordered, and installed.
The notation "P/O Tag/MOD" after a part
number indicates that the item is part of a
Tag/MOD. The notation "Tag/MOD" after a
part number will be used only to indicate the
entire Tag/MOD, whether that is a kit number
or an individual part.
Whenever you install a Tag/MOD kit or all the
piece parts that make up a Tag/MOD, mark
the appropriate number on the Tag/MOD
matrix. PL 1.3 shows the Tag/MOD matrix
location.
Telecopier 7017 / 7017SF
The Change
Go to the
If "piece part" is
associated with the