HP A6616 Installation Manual page 33

For a Combo interface, the default operating interface is the electrical interface. For a Combo interface, the default operating interface is the electrical interface. For a Combo interface, the default operating interface is the electrical interface.

For a Combo interface, you can use either the electrical Ethernet interface or the optical For a Combo interface, you can use either the electrical Ethernet interface or the optical For a Combo interface, you can use either the electrical Ethernet interface or the optical

Ethernet interface. You can use the Ethernet interface. You can use the combo enable { copper | fiber } command in interface
view to switch between the optical and electrical interfaces. For details ab view to switch between the optical and electrical interfaces. For details ab view to switch between the optical and electrical interfaces. For details about the combo
enable { copper | fiber } command, refer to
SR6600 Routers User Manual User Manual.
Use optical transceivers provided by HP only. The device may be incompatible with other Use optical transceivers provided by

optical transceivers and thus displays alarms automatically. optical transceivers and thus displays alarms automatically.
"Hot-swapping" a module refers to first using the swapping" a module refers to first using the remove slot slot-number

the module, and then manually pulling it out, or inserting the module into its slot without the module, and then manually pulling it out, or inserting the module into its slot without the module, and then manually pulling it out, or inserting the module into its slot without
powering off the device. For details about the powering off the device. For details about the remove slot command, refer to
Management in the System Volume
LEDs
Figure 1-24 FIP-210 LEDs
(1) LED for 10/100/1000 Mbps electrical Ethernet interface 0 (GE0) (1) LED for 10/100/1000 Mbps electrical Ethernet interface 0 (GE0)
(2) LED for 10/100/1000 Mbps electrical Ethernet interface 1 (GE1) (2) LED for 10/100/1000 Mbps electrical Ethernet interface 1 (GE1)
(3) Run LED (RUN)
(4) 1000 Mbps optical Ethernet interface LED (SFP1) (4) 1000 Mbps optical Ethernet interface LED (SFP1)
(5) 1000 Mbps optical Ethernet interface LED (SFP0) Mbps optical Ethernet interface LED (SFP0)
Table 1-27 Description of FIP Description of FIP-210 LEDs
LED
RUN (green)
SFP0 and SFP1
(yellow/green)
GE0 and GE1
(yellow/green)
} command, refer to Ethernet Interfaces in the Access Volume
System Volume of HP SR6600 Routers User Manual.
Status
Off Off
Slow blinking (1 Hz) Slow blinking (1 Hz)
Fast blinking (8 Hz) Fast blinking (8 Hz)
Off Off
Solid green Solid green
Blinking green Blinking green
Solid yellow Solid yellow
Off Off
Solid green Solid green
Blinking green Blinking green
Solid yellow Solid yellow
only. The device may be incompatible with other
No power input is available or the FIP No power input is available or the FIP-210 has failed.
The FIP-210 is working normally. 210 is working normally.
Application program is being loaded (in this case, never power Application program is being loaded (in this case, never power
off the device or hot-swap the FIP
may be damaged).
No optical link is present.
An optical link is present.
Data is being sent or received at a rate of 1000 Mbps. Data is being sent or received at a rate of 1000 Mbps.
The optical transceiver has failed in POST. The optical transceiver has failed in POST.
No link is present.
A 1000 Mbps link is present.
Data is being received or transmitted at a rate of 1000 Mbps. received or transmitted at a rate of 1000 Mbps.
A 10/100 Mbps link is present.
} command in interface
Access Volume of HP
command to stop
command, refer to Device
Meaning Meaning
swap the FIP-210; otherwise, the FIP-210