Danfoss VLT 6000 series Operating Instructions Manual page 164

PNU Parameter
# description
300 Terminal 16, Digital input
301 Terminal 17, Digital input
302 Terminal 18, Digital input
303 Terminal 19, Digital input
304 Terminal 27, Digital input
305 Terminal 29, Digital input
306 Terminal 32, Digital input
307 Terminal 33, Digital input
308 Terminal 53, analogue input voltage Reference
309 Terminal 53, min. scaling
310 Terminal 53, max. scaling
311 Terminal 54, analogue input voltage No operation
312 Terminal 54, min. scaling
313 Terminal 54, max. scaling
314 Terminal 60, analogue input current Reference
315 Terminal 60, min. scaling
316 Terminal 60, max. scaling
317 Time out
318 Function after time out
319 Terminal 42, output
320 Terminal 42, output, pulse scaling
321 Terminal 45, output
322 Terminal 45, output, pulse scaling
323 Relay 1, output function
324 Relay 01, ON delay
325 Relay 01, OFF delay
326 Relay 2, output function
327 Pulse reference, max. frequency
328 Pulse feedback, max. frequency
364 Terminal 42, bus control
365 Terminal 45, bus control
Changes during operation:
"Yes" means that the parameter can be changed,
while the frequency converter is in operation. "No"
means that the frequency converter must be stopped
before a change can be made.
4-Setup:
"Yes" means that the parameter can be programmed
individually in each of the four setups, i.e. the
same parameter can have four different data
values. "No" means that the data value will be
the same in all four setups.
Conversion index:
This number refers to a conversion figure to
be used when writing or reading by means
of a frequency converter.
164
Factory setting
Reset
Freeze output
Start
Reversing
Coasting stop, inverse
Jog
No operation
No operation
0.0 V
10.0 V
0.0 V
10.0 V
4.0 mA
20.0 mA
10 sec.
Off
0 - I 0-20 mA
MAX
5000 Hz
0 - f 0-20 mA
MAX
5000 Hz
Alarm
0.00 sec.
0.00 sec.
Running
5000 Hz
25000 Hz
0
0
Data type:
Data type shows the type and length of the telegram.
Data type
3
4
5
6
7
9
MG.61.A5.02 - VLT is a registered Danfoss trademark
®
VLT 6000 HVAC Series
Range Changes 4-Setup
during operation
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
0.0 - 10.0 V Yes Yes
0.0 - 10.0 V Yes Yes
Yes Yes
0.0 - 10.0 V Yes Yes
0.0 - 10.0 V Yes Yes
Yes Yes
0.0 - 20.0 mA Yes Yes
0.0 - 20.0 mA Yes Yes
1 - 99 sec. Yes Yes
Yes Yes
Yes Yes
1 - 32000 Hz Yes Yes
Yes Yes
1 - 32000 Hz Yes Yes
Yes Yes
0 - 600 sec. Yes Yes
0 - 600 sec. Yes Yes
Yes Yes
Depends on Yes Yes
input terminal
0 - 65000 Hz Yes Yes
0.0 - 100 % Yes Yes
0.0 - 100 % Yes Yes
Conversion index
74
2
1
0
-1
-2
-3
-4
Description
Integer 16
Integer 32
Unsigned 8
Unsigned 16
Unsigned 32
Text string
Conversion Data
index type
0 5
0 5
0 5
0 5
0 5
0 5
0 5
0 5
0 5
-1 5
-1 5
0 5
-1 5
-1 5
0 5
-4 5
-4 5
0 5
0 5
0 5
0 6
0 5
0 6
0 5
0 6
0 6
0 5
0 6
0 6
-1 6
-1 6
Conversion factor
0.1
100
10
1
0.1
0.01
0.001
0.0001