Panasonic VariCam LT Operating Manual page 150

Item
[TC] [SET TC]
[SET UB]
[TC/UB/Dur.]
[FREE/REC RUN]
[DF/NDF]
[UB MODE]
[TC IN/OUT SEL]
[TC OUT]
[TC OUT REF]
[REC META DATA] [LOAD]
[RECORD]
[USER CLIP NAME]
[CAM INDEX]
[NEXT REEL COUNT]
[COUNTER RESET]
[PROPERTY]
[REC BEEP SOUND] [MODE]
Chapter 10 Menu Operations — Menu list
Sets the default value of the time code to record.
Hour: [00] - [23]
Minute: [00] - [59]
Second: [00] - [59]
Frame: [00] - [23] (for [24p], [23.98p]), [00] - [24] (for [50i], [50p], [25p]), [00] - [29] (for [59.94i], [59.94p],
[29.97p])
f Factory setting: [00] (various items)
Sets user bits. Enabled only when [USER] is selected in [UB MODE].
This can be set by each digit from [00] to [FF].
f Factory setting: [00]
Switches the time code display to the user bits and duration counter display.
The duration counter is not displayed during the playback.
[TC], [UB], [Dur.]
f Factory setting: [TC]
Sets the operation mode to advance the built-in time code generator. It will be fixed to [REC RUN] when
[MENU] → [CAMERA SETTINGS] → [FPS] → [VFR SW] is set to [ON].
[FREE RUN]: Advances regardless of the operation mode.
[REC RUN]: Advances when recording is in process.
f Factory setting: [FREE RUN]
Sets count method for the built-in time code generator of the camera.
[DF]: Uses the drop frame mode.
[NDF]: Uses the non-drop frame mode.
f Factory setting: [NDF]
Enabled only when [59.94i], [59.94p], or [29.97p] is selected in [MENU] → [SYSTEM SETTINGS] →
[SYSTEM MODE] → [FREQUENCY].
Selects the user bits mode.
[FRAME RATE]: Selects camera imaging information (such as frame rate).
[USER]: Selects the user bits value that has been set.
[EXT INPUT]: Records the user bits values currently input to the <TC IN/OUT> terminal.
[TIME]: Selects the local time. (hh, mm, ss)
[DATE]: Selects the local date and time. (YY, MM, DD, hh)
[USER CLIP NAME (TYPE3)]: CAM INDEX (A-Z) in ASCII character code will go into MSB. Also, the REEL
number in ASCII character code will go into LSB 3 digits.
Example: A123=0x41 0x31 0x32 0x33
0XFFFF is recorded if [USER CLIP NAME] is set to anything other than [TYPE3].
f Factory setting: [USER CLIP NAME (TYPE3)]
Sets the input/output of the <TC IN/OUT> terminal.
[TC IN], [TC OUT]
f Factory setting: [TC IN]
Selects the time code output to the <TC IN/OUT> terminal.
[TCG], [TCG/TCR]
f Factory setting: [TCG]
Sets the output delay of the time code output from the <TC IN/OUT> terminal.
[RECORDING], [SDI OUT]
f Factory setting: [RECORDING]
Loads the metadata upload file saved to the SD memory card.
Sets whether to add loaded metadata at a recording.
[ON]: Adds metadata.
[OFF]: Does not add metadata.
f Factory setting: [OFF]
Sets data to be recorded to [USER CLIP NAME].
(When [RECORD] is [ON])
[TYPE1]: Records setting values of the loaded data.
[TYPE2]: Records the loaded data and counter value.
[TYPE3]: Records the setting value prescribed with CAM INDEX or REEL number.
(When [RECORD] is [OFF])
[TYPE1]: Records the same value as [GLOBAL CLIP ID].
[TYPE2]: Records the same value as [CLIP NAME].
[TYPE3]: Records the setting value prescribed with CAM INDEX or REEL number.
f Factory setting: [TYPE3]
Sets CAM INDEX used in [TYPE3] of [USER CLIP NAME].
[A] - [Z]
f Factory setting: [A]
Sets REEL used in [TYPE3] of [USER CLIP NAME]. The REEL number for the card that the REEL number
is already assigned would not change.
[001] - [999]
f Factory setting: [001]
Resets the counter value when [USER CLIP NAME] is set to [TYPE2].
Checks loaded metadata. This cannot be modified.
Sets if the beep sound is generated when starting or stopping the recording.
[OFF]: The beep sound is not generated.
[START]: The beep sound is generated only when the recording is started.
[STOP]: The beep sound is generated only when the recording is stopped.
[START & STOP]: The beep sound is generated when the recording is started and stopped. The output
time of the beep sound when the recording is stopped will be 1.5 times of when the recording is started.
f Factory setting: [OFF]
– 150 –
Description of settings