Panasonic VariCam LT Operating Manual page 146

Item
[KNEE] [KNEE SW]
(page 74)
[KNEE MODE]
[KNEE POINT]
[KNEE SLOPE]
[WHITE CLIP] [SW]
(page 75)
[LEVEL]
[DETAIL] [SW]
[CORING]
[MASTER LEVEL]
[FREQUENCY]
[SKIN DETAIL] [SW]
(page 75)
[TABLE SELECT]
[GET]
[ZEBRA SW]
[EFFECT LEVEL]
[DETECT TABLE]
[- I CENTER]
[- I WIDTH]
[- Q WIDTH]
[- Q PHASE]
[CHROMA] [LEVEL]
[PHASE]
[LINEAR MATRIX] [SW]
(page 77)
[(R-G)_N]
Chapter 10 Menu Operations — Menu list
Enables/disables knee operation.
[ON], [OFF]
f Factory setting: [OFF]
Sets the knee operation mode.
[D RANGE]: Determines the dynamic range that can be represented by the [KNEE SLOPE] value. The
dynamic range that can be represented does not change even if the [KNEE POINT] value changes.
[PRESS]: Determines the signal compression rate through the [KNEE SLOPE] value. The value of the
dynamic range that can be represented changes when the [KNEE POINT] value changes.
f Factory setting: [D RANGE]
Sets the position of the knee point.
[75%] - [109%] (1% step)
f Factory setting: [85%]
Sets the knee inclination.
[0] - [100]
f Factory setting: [100]
Switches the enable/disable of the white clip function.
[ON], [OFF]
f Factory setting: [OFF]
Sets the white clip function level.
[90%] - [109%]
f Factory setting: [109%]
Switches the enable/disable of the detail function.
[ON], [OFF]
f Factory setting: [OFF]
Sets the coring amount for the detail signal.
[0] - [60]
f Factory setting: [1]
Sets the effect level for the detail signal.
[−31] - [31]
f Factory setting: [0]
Sets the thickness of the detail.
[1] - [3]
f Factory setting: [3]
Switches enable/disable of the skin tone detail function.
[OFF], [ON]
f Factory setting: [OFF]
Selects the table for the skin tone detail.
[A], [B], [C], [A+B], [A+C], [B+C], [A+B+C]
f Factory setting: [A]
Sets whether to register the screen center color as the color by which the skin tone detail is applied.
[EXECUTE], [CANCEL]
Sets whether to superimpose the zebra signal to the color by which the skin tone detail is applied.
[ON], [OFF]
f Factory setting: [OFF]
Sets the effective level of the skin tone detail. The higher the value, the more significant the effect.
[0] - [31]
f Factory setting: [16]
Selects the skin tone table of the subject that displays the skin tone detail.
[A], [B], [C]
f Factory setting: [A]
Sets the center position of the upper I axis (setting the area that displays the skin tone).
[0] - [255]
f Factory setting: [35]
Sets the width of the area that displays the skin tone of the upper I axis that focus on [- I CENTER].
[0] - [255]
f Factory setting: [55]
Sets the width of the area that displays the skin tone of the upper Q axis that focus on [- I CENTER].
[0] - [127]
f Factory setting: [22]
Sets the phase of the area that displays the skin tone regarding to the Q axis.
[0] - [255]
f Factory setting: [0]
Sets the chroma level of P and P
R
[OFF], [−99%] - [99%]
f Factory setting: [0%]
Fine adjusts the chroma phase of P
[−31] - [31]
f Factory setting: [0]
Enables/disables the linear matrix function.
[ON], [OFF]
f Factory setting: [OFF]
Adjusts the linear matrix.
[−127] - [127]
f Factory setting: [0]
– 146 –
Description of settings
signals.
B
and P signals.
R B