Page 1 Avaya Reference Guide P330-ML-ML VAYA TACKABLE WITCH OFTWARE ERSION January 2004...
Page 3: Table Of Contents
Entering the Technician Level ... 7 Warranty ... 7 Notice... 7 Avaya Support ... 7 Chapter 2 Avaya P330-ML Layer 2 CLI Commands... 9 clear cam ... 9 clear dot1x config ... 9 clear dynamic vlans ... 10 clear log ... 10 clear logging file ...
Page 14 Router OSPF Context... 293 area ...293 network ...293 passive-interface ...294 redistribute ...294 timers spf ...295 Router SRRP Context ... 296 poll-interval ...296 timeout ...296 Index of Layer 2 CLI Commands... 297 Index of Layer 3 CLI Commands... 301 Avaya P330-ML Reference Guide...
Page 15: Using The Cli
Enter. You can also configure your Avaya P330 using the P330 Manager with its graphical user interface. For details, see the switch User’s Guide and the Avaya™...
Page 16: Chapter 1 Using The Cli
The CLI contains a simple text editor with these functions: Table 1.1 Navigation, Cursor Movement and Shortcuts Keyboard Backspace Up arrow/Down arrow Left arrow/Right arrow Functions Deletes the previous character Scrolls back and forward through the command history buffer Moves the cursor left or right Avaya P330-ML Reference Guide...
Page 17: Navigation, Cursor Movement And Shortcuts
For ambiguous commands, type the beginning letters on the command line and then use the Tab key to toggle through all the possible commands beginning with these letters. Avaya P330-ML Reference Guide Chapter 1 Functions Completes the abbreviated command. Type the minimum number of characters unique to the command.
Page 18: Universal Commands
The syntax for this command is: tree P330 Sessions You can use sessions to switch between the CLI of P330 modules / other stack entities (for example, an X330 ATM or WAN entity plugged into a specific P330 switch or with the G700 Media Gateway Precessor) or to switch between Layer 2 and Layer 3 commands in the router module.
Page 19: Security Levels
Chapter 1 Using the CLI To configure the switch parameters, on module 6, type the command: session 6 switch. Note: When you use the session command the security level stays the same. Note: Use the session command without any parameters to identify the stack master and its slot number.
Page 20: Entering The Supervisor Level
Switching between the entities, does not effect the security level since security levels are established specifically for each user. For example, if the operator with a privileged security level in the Switch entity switches to the Router entity the privileged security level is retained.
Page 21: Entering The Cli
Avaya Support Avaya provides a telephone number for you to use to report problems or to ask questions about your contact center. The support telephone number is 1-800-242- 2121 in the United States. For additional support telephone numbers, see the Avaya Web site: http://www.avaya.com...
Page 22 Chapter 1 Using the CLI Avaya P330-ML Reference Guide...
Page 23 Chapter 2 Avaya P330-ML Layer 2 CLI Commands This chapter describes all the P330-ML Layer 2 CLI commands and parameters in alphabetical order. clear cam User level: privileged, supervisor. Use the clear cam command to delete all entries from the CAM table.
Page 24: Chapter 2 Avaya P330-Ml Layer 2 Cli Commands
User level: privileged, supervisor. This command is available on the P330-ML-ML only. Use the clear dynamic vlans command to clear dynamically learned VLANs. Only the VLANs learned by the switch from incoming traffic are cleared using this command.
Page 25: Clear Log
- do you want to continue (Y/N)? Mirroring packets from port 1/2 to port 1/4 is cleared Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The IP address of the Syslog server. Source module number Source port number...
Page 26: Clear Port Static-Vlan
Chapter 2 Avaya P330-ML Layer 2 CLI Commands clear port static-vlan User level: privileged, supervisor. Use the clear port static-vlan command to delete VLANs statically configured on a port. The syntax for this command is: clear port static-vlan [module/port range][vlan num]...
Page 27: Clear Rmon Statistics
User level: user, privileged, supervisor If this command is to be implemented on a switch other than the stack master, a session should be opened to the relevant switch. Use the clear secure mac command to remove a MAC address from the CAM table of a secured port.
Page 28: Clear Snmp Trap
Chapter 2 Avaya P330-ML Layer 2 CLI Commands clear snmp trap User level: privileged, supervisor. Use the clear snmp trap command to clear an entry from the SNMP trap receiver table. The syntax for this command is: clear snmp trap {<rcvr_addr>|all}...
Page 29: Clear Utilization Cpu
Use the copy module-config scp command to upload the switch-level parameters from the current NVRAM running configuration into a file via SCP. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The module number for which CPU utilization monitoring is disabled. VLAN number...
Page 30: Copy Module-Config Tftp
Chapter 2 Avaya P330-ML Layer 2 CLI Commands The syntax for this command is: copy module-config scp <filename> <ip> <mod_num> filename mod-num Example: P330-N# copy module-config scp c:\config\switch1.cfg 192.168.49.10 5 Username: 330user Password: Beginning upload operation ... This operation may take a few minutes...
Page 31: Copy Running-Config Scp
User level: supervisor Use the copy running-config scp command to upload the current switch-level parameters from the current NVRAM running configuration into a file via SCP. The syntax for this command is: copy running-config scp <filename> <ip> <mod_num>...
Page 32: Copy Running-Config Startup-Config
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N# copy running-config scp c:\config\switch1.cfg 192.168.49.10 5 Username: 330user Password: Beginning upload operation ... This operation may take a few minutes... Please refrain from any other operation during this time. For more information , use 'show upload status' command...
Page 33 The ip address of the tftp server. Example (for Windows): P330-N# copy running-config tftp c:\P330-ML\startup.cfg 149.49.100.41 Example: (for Unix): P330-N# copy running-config tftp /folder/P330- ML/startup.cfg 149.49.100.41 Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands...
Page 34: Copy Scp Module-Config
Use the copy scp module-config command to download a module configuration to the device via SCP. Only parameters that differ from the factory default settings for the switch are included in the configuration file. Therefore, it is important to reinitialize the NVRAM to the factory default settings before downloading configuration files to the switch.
Page 35: Copy Scp Stack-Config
Use the copy scp stack-config command to download a stack configuration to the device via SCP. Only parameters that differ from the factory default settings for the switch are included in the configuration file. Therefore, it is important to reinitialize the NVRAM to the factory default settings before downloading configuration files to the switch.
Page 36 Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example (for Windows): P330-N# copy scp stack-config c:\P330-ML\stack.cfg 149.49.100.41 Username: 330user Password: Beginning download operation ... This operation may take a few minutes... Please refrain from any other operation during this time.
Page 37: Copy Scp Startup-Config
Use the copy scp startup-config command to download a startup configuration to the device via SCP. Only parameters that differ from the factory default settings for the switch are included in the configuration file. Therefore, it is important to reinitialize the NVRAM to the factory default settings before downloading configuration files to the switch.
Page 38: Copy Stack-Config Scp
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: (for Unix): P330-N# copy scp startup-config /folder/P330-ML/startup.cfg 149.49.100.41 Username: 330user Password: Beginning download operation ... This operation may take a few minutes... Please refrain from any other operation during this time.
Page 39: Copy Stack-Config Tftp
* it is recommended to exit from it before performing configuration* * download operations. ******************************************************************** Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The file name (full path) The IP address of the TFTP server...
Page 40: Copy Startup-Config Scp
Use the copy startup-config tftp command to download a policy configuration from a TFTP server. Only parameters that differ from the factory default settings for the switch are included in the configuration file. Therefore, it is important to reinitialize the NVRAM to the factory default settings before downloading configuration files to the switch.
Page 41: Copy Tftp Ew_Archive
Example: (for Unix): P330-N# copy tftp EW-archive /folder/startup.cfg 149.49.100.41 5 Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands P330-ML Manager image file name (full path) The IP address of the host Module to download the embedded web to...
Page 42: Copy Tftp Module-Config
NVRAM running configuration of a switch from a TFTP server. Only parameters that differ from the factory default settings for the switch are included in the configuration file. Therefore, it is important to reinitialize the NVRAM to the factory default settings before downloading configuration files to the switch.
Page 43: Copy Tftp Startup-Config
TFTP file to the Startup Configuration file in the NVRAM. Only parameters that differ from the factory default settings for the switch are included in the configuration file. Therefore, it is important to reinitialize the NVRAM to the factory default settings before downloading configuration files to the switch.
Page 44: Copy Tftp Sw_Image
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: (for Unix): Router-N (super) # copy tftp startup-config /folder/startup.cfg 149.49.100.41 copy tftp SW_image User level: supervisor Use the copy tftp SW_image command to download a new firmware software version into bank B while either keeping the old version in bank A, or downloading the Embedded Web manager software into bank A.
Page 45 Destination file : P330-ML Host Running state Failure display Last warning Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands : /home/P330-ML/viisa : 135.64.103.104 : Download Process Started : no-error : /home/P330-ML/viisa : 135.64.103.104 : Testing ...
Page 46: Crypto Key Generate Dsa
Chapter 2 Avaya P330-ML Layer 2 CLI Commands copy tftp SW_powerinline_image User level: supervisor This command applies to P333T-PWR switches only and is used by P330- ML-ML switches to control P333T-PWR modules in the stack. Use the copy tftp SW_powerinline_image command to update the inline software application from a TFTP server to the memory of a designated module.
Page 47: Dir
EW_Archive Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands A keyword specifying that the key lenght is provided by the user. The number of bits in the key. Possible values are: 512 – 2048. The default is 768 bits.
Page 48: Disconnect Ssh
• Running Conf – the configuration currently in use. • Startup-config - startup configuration for policy and routing in the P330-ML-ML, P333R, and P333R-LB • SW boot image - Booter file • SW Web Image – Device Manager S/W archive file...
Page 49: Get Time
The syntax for this command is: help [<command> [<subcommand>...]] Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The SSH session ID. Use the show ssh command to learn an SSH session ID.
Page 50: Hostname
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>help username Username commands: ---------------------------------------------------------- Usage: username <name> password <passwd> access-type {read- only|read-write|admin} hostname User level: privileged, supervisor. Use the hostname command to change the Command Line Interface (CLI) prompt. The current module number always appears at the end of the prompt.
Page 51 1.2.0.0 0.0.255.255 Router-N# ip access-list 101 24 fwd3 udp any host 10.1.1.1 range 20 23 optional Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands <action> <protocol> {<source-ip> <source-wildcard> | any |host <source-ip>}[<operator> <port> [<port]] {<destination-ip> <destination- wildcard>|any |host...
Page 52: Ip Access-List-Cookie
Chapter 2 Avaya P330-ML Layer 2 CLI Commands The P334T-ML does not support ‘lt’ and ‘gt’ port operators. ip access-list-cookie User level: supervisor This command applies to the P334T-ML only when it is in device mode "Layer2". Use the ip access-list-cookie command to set the list cookie for a specific policy list.
Page 53: Ip Access-Default-Action
<action> policy- A valid id number for a policy list currently defined for the module list- (100..149) number dscp DSCP value or range of DSCP Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands integer (100...149) default-action-deny|default-action-permit...
Page 54: Ip Access-List-Dscp Trust
Chapter 2 Avaya P330-ML Layer 2 CLI Commands action permit | deny | deny-and-notify | fwd0 | fwd1... fwd7: • permit: do nothing, let the packet pass • deny: drop the packet • deny-and-notify: drop the packet and send an SNMP trap •...
Page 55: Ip Access-List-Name
The syntax for this command is: ip access-list-owner <policy-list-number> <owner> <policy-list-number> <owner> Example: Router-N# ip access-list-owner 101 admin Done! Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands integer (100...149) list name integer (100...149) list owner...
Page 56: Ip Http Enable
Chapter 2 Avaya P330-ML Layer 2 CLI Commands ip http enable User level: supervisor Use the ip http enable command to enable HTTP access to the device. The syntax for this command is: ip http enable Example: P330-N# ip http enable...
Page 57: Ip Ssh Enable
Example: P330-N# ip telnet enable Done! Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands source ip address destination ip address ip | tcp | udp | integer (1...255) integer (1...65535) integer (1...65535) value of TCP established bit...
Page 58: Ip Telnet-Client Enable
Chapter 2 Avaya P330-ML Layer 2 CLI Commands ip telnet-client enable User level: supervisor Use the ip telnet-client enable command to enable the device to act as a Telnet client. This command can only be run from the console port on the device.
Page 59: No Ip Ssh
Use the no ip telnet-client command to disable the device from acting as a Telnet client. This command can only be run from the console port on the device. The syntax for this command is: no ip telnet-client Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands...
Page 60: No Rmon Alarm
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N# no ip telnet-client Done! no rmon alarm User level: privileged, supervisor. Use the no rmon alarm command to delete an existing RMON alarm entry. The syntax for this command is: no rmon alarm <Alarm Index>...
Page 61: No Rmon History
The syntax for this command is: no snmp-server engineID Example: P330-N# no snmp-server engineID EngineID return to default Done! Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands History index defined using rmon history command or RMON management tool...
Page 62: No Snmp-Server Community
Chapter 2 Avaya P330-ML Layer 2 CLI Commands no snmp-server community User level: supervisor Use the no snmp-server community command to deny access to the device using community strings. The syntax for this command is: no snmp-server community Example: P330-N# no snmp-server community...
Page 63: No Snmp-Server Host
-type-list (Optional) Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Specifies the address (or host name) of the notification recipient agent. The maximum length is 32 bytes. List of notification types. Each types combines related notifications. You can disable notification generations on a per group basis.
Page 64: No Snmp-Server Notifications
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>no snmp-server host 149.49.38.221 Done! no snmp-server notifications User level: supervisor Use the no snmp-server notifications command to disable all available SNMP notifications. The syntax for this command is: no snmp-server notifications...
Page 65: No Snmp-Server View
Use the no username command to remove a local CLI user account. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Variable that specifies the name of the SNMP user. The maximum length is 32 bytes. The security model assigned to the user in user to group association.
Page 66: Nvram Initialize
Chapter 2 Avaya P330-ML Layer 2 CLI Commands The syntax for this command is: no username <name> name Example: P330-1(super)# no username john User account removed. If you wish to delete a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 67: Prompt-Length
Display the full length of the prompt prompt- Set the length in characters of the prompt to display size Example: P330-ML-1(super)# prompt-length 4 ~r)# reset Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands min/avg/max = 0/0/0...
Page 68: Reset Mgp
Avaya P330-ML Layer 2 CLI Commands User level: user, privileged, supervisor Use the reset command to restart the stack or an individual switch. If no switch number is defined or the switch number of the Master is defined, the command resets the entire stack.
Page 69: Reset Stack
User level: supervisor Use the retstatus to display the return status of the previously executed command. The syntax for this command is: retstatus Example: P330-N# retstatus Succeeded Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands...
Page 70: Rmon Alarm
Chapter 2 Avaya P330-ML Layer 2 CLI Commands rmon alarm User level: privileged, supervisor. Use the rmon alarm command to create a new RMON alarm entry. The syntax for this command is: rmon alarm <Alarm Number> <variable> <interval> <sample type>...
Page 71: Rmon Event
Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands This is the event index number of this entry. The type of the event. The possible parameters are: • trap • log • logAndTrap •...
Page 72: Session
Use the session command to open a session with a specific entity within a switch or the stack. For example, you can open a session with the Routing entity of a P330-ML-ML switch in the stack, or with an the X330 ATM (or X330 WAN) sub- module entity plugged into a specific switch.
Page 73: Set Allowed Managers
[add | delete][IP address] delete IP address Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Adds specified IP address to the Allowed Managers table Deletes specified IP address from the Allowed Managers table...
Page 74: Set Arp-Aging-Interval
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N# set allowed managers ip add 149.49.32.134 Ip was added to the table set arp-aging-interval User level: privileged, supervisor. Use the set arp-aging interval command to set the ARP table aging interval for entries in the agent Layer 2 ARP table.
Page 75: Set Autopartition
User level: privileged, supervisor. This command is not relevant to P330-ML-ML switches. It appears in the P330- ML-ML CLI for controlling autopartition of other P330-ML switches in the stack. Use the set autopartition command to enable or disable auto-partitioning on P330-ML switches in the stack.
Page 76: Set Cascading
User level: privileged, supervisor. Use the set device-mode command to select the module’s operating mode — Layer 2 or Router . This command is available on P330-ML-ML and P333R switches only. The syntax for this command is: set device-mode <mode>...
Page 77: Set Dot1X Quiet-Period
The syntax for this command is: set dot1x re-authperiod <Seconds> Seconds Number of seconds – 0 to 65535 Example: P330-1(super)# set dot1x re-authperiod 90 Done! set dot1x server-timeout Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands...
Page 78: Set Dot1X Supp-Timeout
User level: supervisor Use the set dot1x supp-timeout command to set the maximum time that the switch will wait for a reply from the Authenticated Station before the session is terminated. The syntax for this command is: set dot1x supp-timeout <Seconds>...
Page 79: Set Dot1X System-Auth-Control Enable
Use the set dot1x tx-period command to set the time interval between attempts to access the Authenticated Station. The syntax for this command is: set dot1x tx-period <Seconds> Seconds Number of seconds – 0 to 65535 Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands...
Page 80: Set Inband Vlan
Use the set intelligent-multicast client port pruning time command to set the aging time for client ports. This is the time after the P330-ML switch reset during which the filtering information is learned by the switch but not configured on the ports.
Page 81: Set Intelligent-Multicast Group-Filtering-Delay Time
User level: privileged, supervisor. Use the set intelligent-multicast group-filtering delay time command to set group filtering time delays. This is the time that the switch waits between becoming aware of a Multicast group on a certain VLAN and starting to filter traffic for this group.
Page 82: Set Interface Inband
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N# set intelligent-multicast router-port-pruning-time Done! set interface inband User level: privileged, supervisor. Use the set interface inband command to configure the Management inband interface on the Master agent in the stack.
Page 83: Set Interface Ppp Enable/Enable-Always/Disable/Off/Reset
PPP has reset the connected modem. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands IP address used by the P330-ML Supervisor Module to connect via its PPP interface Subnet mask used by the P330-ML Supervisor Module to connect via its PPP interface Enable PPP and enter modem mode.
Page 84: Set Intermodule Port Redundancy
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N# set interface ppp enable Entering the Modem mode within 60 seconds... Please check that the proprietary modem cable is plugged into the console port Example: P330-N# set interface ppp disable...
Page 85: Set Intermodule Port Redundancy Off
Intermodule port redundancy entry deleted. set internal buffering User level: privileged, supervisor. This command is not relevant to P330-ML-ML switches. It appears in the P330- ML-ML CLI for controlling internal buffering of other P330-ML switches in the stack. The set internal buffering command allows you to set the size (Maximum, Medium, and Minimum) of the Receive (Rx) buffer allocated to each port of the specified switch.
Page 86: Set Ip Route
User level: privileged, supervisor. Use the set license command to activate the SMON and Routing capabilities of the Avaya P330-ML stack. An Avaya P330-ML stack can include several Avaya P330-ML switches. One SMON license is required per Avaya P330-ML stack; a routing license is required for each P330-ML-ML switch in the stack.
Page 87: Set Logging File Condition
{ all | <application> } { none | <severity> } Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Switch number License number Name of the feature, either smon or routing A keyword signifying that messages from all applications are...
Page 88 Chapter 2 Avaya P330-ML Layer 2 CLI Commands application none severity The application from which logging messages are logged to the logging file. Possible values are: • BOOT • SYSTEM • ROUTER • CONFIG • FILESYS • FAN • SUPPLY •...
Page 89: Set Logging File Disable
Use the set logging server command to define the IP address of a logging server. You may define up to three logging servers. set logging server <ip-address> ip-address Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The IP address of the Syslog server.
Page 90: Set Logging Server Access-Level
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N# set logging server 149.49.38.22 Done! set logging server access-level User level: privileged, supervisor. Use the set logging server access-level command to define the access level associated with Syslog server sink. The user cannot specify an access level higher than the level assigned to him.
Page 91 Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands A keyword signifying that the specified severity threshold applies to all applications. The application to which the filter applies. Possible values are: • BOOT • SYSTEM •...
Page 92: Set Logging Server Disable
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N# set logging server condition LAG Warning 135.64.102.224 Done! set logging server disable User level: privileged, supervisor. Use the set logging server disable command to disable logging messages to a Syslog server.
Page 93: Set Logging Server Facility
<server-facility> <ip-address> server-facility ip-address Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The facility used for sending messages to the Syslog server. Possible values are: • kern – Kernel • user – User processes •...
Page 94: Set Logging Session Condition
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N# set logging server facility news 135.64.102.224 Done! set logging session condition User level: privileged, supervisor. Use the set logging session condition command to define a filter rule for logging messages during the current session.
Page 95: Set Logging Session Disable
CLI session. The syntax for this command is: set logging session enable Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The minimum severity of the logging messages that are logged. Possible values are: • Emergency • Alert •...
Page 96: Set Logout
Sessions will not be automatically logged out. set mac-aging User level: privileged, supervisor. This command is available on the P330-ML-ML switches only. Use the set mac-aging command to enable or disable the MAC aging function. Time until the system automatically disconnects an idle session.
Page 97: Set Mac-Aging-Time
User level: privileged, supervisor. This command is available on the P330-ML-ML switches only. Use the set mac-aging-time command to set the MAC aging time in minutes. This is the time after which unused MAC addresses in the MAC table are erased.
Page 98: Set Port Channel
User level: privileged, supervisor. Use the set port channel command to enable or disable a Link Aggregation Group (LAG) interface on the switch. LAG creation requires a LAG name to be specified. There is no default name. You can also add or remove a port from an existing LAG. When adding or removing a port to an existing LAG, type the same LAG-name.
Page 99: Set Port Classification
Use the set port disable command to disable a port or range of ports. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands A list of ports to be aggregated in the format module/port on or off – enables or disables the channel for the specified...
Page 100: Set Port Dot1X Initialize
Chapter 2 Avaya P330-ML Layer 2 CLI Commands The syntax for this command is: set port disable <mod_num>/<port_num> module port Example: P330-N# set port disable 4/1 Port 4/1 disabled. set port dot1x initialize User level: supervisor Use the set port dot1x initialize command to initialize port dot1x.
Page 101: Set Port Dot1X Port-Control
1/2 control was set to force-authorize set port dot1x quiet-period User level: supervisor Use the set port dot1x quiet-period command to set the 802.1x quiet period per port. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands...
Page 102: Set Port Dot1X Re-Authenticate
Chapter 2 Avaya P330-ML Layer 2 CLI Commands The syntax for this command is: set port dot1x quiet-period <module/port> <seconds> module/ Module and port number (or range of ports) port seconds Number of seconds – 0 to 65535 Example: P330-1(super)# set port dot1x quiet-period 4/2 300...
Page 103: Set Port Dot1X Re-Authperiod
<module/port> <seconds> module/ Module and port number (or range of ports) port seconds Number of seconds – 0 to 65535 Example: P330-1(super)# set port dot1x server timeout 1/2 400 Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands...
Page 104: Set Port Dot1X Supp-Timeout
Chapter 2 Avaya P330-ML Layer 2 CLI Commands set port dot1x supp-timeout User level: supervisor Use the set port dot1x supp-timeout command to set the time for the port to wait for a reply from the Authentication Server before the session is terminated.
Page 105: Set Port Edge Admin State
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Number of the switch in the stack. If you do not specify a number, the ports on all the switches are shown. Number of the port on the module. If you do not specify a number, all the ports on the module are shown.
Page 106: Set Port Enable
Chapter 2 Avaya P330-ML Layer 2 CLI Commands admin The port’s admin satte can be set to either edge-port or non-edge- state port. Examples: P330-N# set port edge admin state 1/1 edge-port port 1/1 edge admin state is set to edge-port...
Page 107: Set Port Level
<module>/<port> [value] module Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Indicates whether the port can receive administrative status from a remote device. Available only for Gigabit Ethernet modules with negotiation set to off.
Page 108: Set Port Mirror
Chapter 2 Avaya P330-ML Layer 2 CLI Commands port value Example: P330-N# set port level 3/1 5 Port 3/1 level set to 5 set port mirror User level: privileged, supervisor. Use the set port mirror command to define a port mirroring pair in the stack.
Page 109: Set Port Name
100Mbps (Full Duplex), and autonegotiation should be disabled on both cable ends. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Number of the switch. Number of the port on the switch. Name (up to 16 characters)
Page 110: Set Port Point-To-Point Admin Status
P330-N# set port point-to-point admin status 1/1 force-true port 1/1 point to point admin status is set to force-true Number of the switch. If you do not specify a number, the ports on all the switches are shown. Number of the port on the module.
Page 111: Set Port Powerline
Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Number of the module hosting the port for which a powerline priority level is to be set. Number of the port for which a powerline priority level is...
Page 112: Set Port Redundancy
Chapter 2 Avaya P330-ML Layer 2 CLI Commands priority Example: Router-N# set port powerinline priority 2/3 HighLoad Powering priority on port/s 2/3 was set to High set port redundancy User level: privileged, supervisor. Use the set port redundancy command to globally enables or disable the port redundancy pairs you have defined.
Page 113: Set Port Redundancy-Intervals
Example: P330-N# set port redundancy-intervals 100 20 Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The minimum time between redundancy switchovers for each pair (in milliseconds). The period the primary port link has to be “up” before the system switches back (in milliseconds).
Page 114: Set Port Security
Chapter 2 Avaya P330-ML Layer 2 CLI Commands set port security User level: supervisor Use the set port security command to enable MAC security on a port or a range of ports at the module level. The port security is activated only after you enable the secutity mode at the stack level using the set security mode command.
Page 115: Set Port Spantree Disable
RSTP port (and not as common STA port). It forces the port to send a rapid spanning tree BPDU. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Module number Port number Module number...
Page 116: Set Port Spantree Priority
Chapter 2 Avaya P330-ML Layer 2 CLI Commands The syntax for this command is: set port spantree force-protocol-migration <module/port> module/ Port identifier port Example: P330-N>set port spantree force-protocol-migration 1/1 port 1/1 is forced to send a Rapid spanning tree BPDU set port spantree priority User level: privileged, supervisor.
Page 117: Set Port Static-Vlan
Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Number of the switch. Number of the port on the switch. You can also specify a range of ports separated by a dash, for example, 4/5-13 for ports 5 to 13 on module 4.
Page 118: Set Port Trap
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N# set port static-vlan 3/4-6 2 VLAN 2 is bound to port 3/4 VLAN 2 is bound to port 3/5 VLAN 2 is bound to port 3/6 set port trap User level: privileged, supervisor.
Page 119: Set Port Vlan-Binding-Mode
Set Port vlan binding method:5/9 Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The switch number Number of the port on the switch. You can also specify a range of ports separated by a dash, for example, 4/5-13 for ports 5 to 13 on module 4.
Page 120: Set Powerinline External Power
Chapter 2 Avaya P330-ML Layer 2 CLI Commands set powerinline external power User level: privileged, supervisor. This command applies to P333T-PWR switches only and is used by P330- ML-ML switches to control P333T-PWR modules in the stack. Use the set powerinline external power command to set the maximum power available from the external power supply to power DTEs.
Page 121: Set Ppp Baud-Rate
PPP incoming session. The syntax for this command is: set ppp incoming timeout <time> time Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The shared secret, 4 to 32 characters. The timeout in minutes...
Page 122: Set Psu Type
Use the set psu type command to set the main power supply type (AC/DC) of the module. This command is not applicable to P330-ML-ML switches, which determine the PSU type automatically. This command is used to set the power supply types for other P330-ML switches in the stack.
Page 123: Set Queuing Scheme
The module number to which the queuing scheme applies. If no module is specified, the command affects all P330-ML-ML modules in the stack. Examples: P330-N# set queuing scheme wrr 10 2...
Page 124: Set Radius Authentication Retry-Number
Chapter 2 Avaya P330-ML Layer 2 CLI Commands The syntax for this command is: set radius authentication {enable|disable} enable disable Example: P330-1(super)# set radius authentication enable set radius authentication retry-number User level: privileged, supervisor. Sets the number of times an access request is sent when there is no response.
Page 125: Set Radius Authentication Secret
Normally, the UDP port number should be set to its default value of 1812. Some early implementations of the RADIUS server used port number 1645. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands IP address of the RADIUS authentication server default - Primary authentication server Secondary authentication server...
Page 126 Chapter 2 Avaya P330-ML Layer 2 CLI Commands The syntax for this command is: set radius authentication udp-port <number> Example: P330-1(super)# set radius authentication udp-port 300 Avaya P330-ML Reference Guide...
Page 127: Set Secure Mac
User level: user, privileged, supervisor Use the set security violation command to specify the security violation action to be taken. This command is only available on P330-ML-ML switches. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands...
Page 128: Set Snmp Community
Switch security violation action restrict set snmp community User level: privileged, supervisor. Use the set snmp community command to set or modify the switch’s SNMP community strings. The syntax for this command is: set snmp community <read-only | read-write | trap> [community...
Page 129: Set Snmp Timeout
Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Timeout in seconds Activate SNMP traps Deactivate SNMP traps (Optional) Specify all trap types (Optional) Specify the ConfigChange trap from the TRAP-MIB. (Optional) Specify the Fault trap from the TRAP-MIB.
Page 130: Set Snmp Trap Auth
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: To enable SNMP ConfigChange traps to a specific manager: P330-N# set snmp trap 192.168.173.42 enable config SNMP config change traps enabled. Example: To enable all traps to a specific manager: P330-N# set snmp trap 192.168.173.42 enable all SNMP all traps enabled.
Page 131: Set Spantree Default-Path-Cost
When you disable STP, blocking ports are disabled in order to prevent loops in the network. As a result, you need to wait 30 seconds before disabling STP if you reset the switch, enable STP, or insert a new station. The syntax for this command is:...
Page 132: Set Spantree Forward-Delay
Chapter 2 Avaya P330-ML Layer 2 CLI Commands The syntax for this command is: set spantree enable Example: P330-N# set spantree enable bridge spanning tree enabled. set spantree forward-delay User level: privileged, supervisor. Use the set spantree forward-delay command to set the bridge forward delay time parameter.
Page 133: Set Spantree Max-Age
Bridge priority set to 4096. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The priority level is from 0 to 61440, with 0 indicating high priority and 61440 indicating low priority; value should be in steps of 4096. Default value is 32768.
Page 134: Set Spantree Tx-Hold-Count
Chapter 2 Avaya P330-ML Layer 2 CLI Commands set spantree tx-hold-count User level: privileged, supervisor. Use the set spantree tx-hold-count command to limit the maximum number of BPDUs transmitted during a hello-time period. The syntax for this command is: set spantree tx-hold-count <rate>...
Page 135: Set System Contact
“new york”. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands • The contact name string should be typed inside inverted commas. • The name is cleared if you leave this field blank.
Page 136: Set System Name
Chapter 2 Avaya P330-ML Layer 2 CLI Commands set system name User level: privileged, supervisor. Use the set system name command to set the mib2 system name MIB variable. The syntax for this command is: set system name [string] string Example: P330-N# set system name “P330-ML-1”...
Page 137: Set Time Client
User level: privileged, supervisor. Use the set time client command to enable or disable the periodic network time acquisition by the switch from the network time server (SNTP or TIME protocol). The syntax for this command is:...
Page 138: Set Time Server
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>set time protocol sntp-protocol The protocol has been set to SNTP protocol P330-N> set time protocol time-protocol The protocol has been set to TIME protocol set time server User level: privileged, supervisor.
Page 139: Set Trunk
CPU utilization is set on module 1 Done! Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Number of the switch. Number of the port on the switch. You can also specify a range of ports separated by a dash, for example, 4/5-13 for ports 5 to 13 on switch 4.
Page 140: Set Vlan
Chapter 2 Avaya P330-ML Layer 2 CLI Commands set vlan User level: privileged, supervisor. Use the set vlan command to configure VLANs. The syntax for this command is: set vlan <vlan-id> [name <vlan-name>] vlan-id vlan-name Example: P330-N# set vlan 3 name gregory VLAN id 3, vlan-name gregory created.
Page 141: Set Welcome Message
- Restores the default string. Example: P330-N# set welcome message avaya The new welcome string is “avaya” If you wish to define a string which includes spaces, you must enclose the entire string in quotation marks, e.g. "new york".
Page 142: Show Allowed Managers Status
Chapter 2 Avaya P330-ML Layer 2 CLI Commands show allowed managers status User level: user, privileged, supervisor Use the show allowed managers status command to display the activation status of the Allowed Managers feature. The syntax for this command is:...
Page 143: Show Arp-Aging-Interval
P330-N>show arp-aging-interval ARP table aging interval was set to 10 minutes. show arp-tx-interval User level: privileged, supervisor. Use the show arp-tx-interval command to display the keep-alive frames transmission interval. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands...
Page 144: Show Autopartition
User level: privileged, supervisor. Use the show autopartition command to display the automatic partition. Autopartition for the P330-ML-ML switches will always have the value disabled. This command is used to display the autopartition status for the other P330-ML switches in the stack.
Page 145: Show Boot Bank
You must issue this command separately for each switch in the stack using the session command. If you wish to run this command on a switch other than the stack master, you need to open a session to the relevant switch.
Page 146: Show Cam Mac
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: (by Module/Port) P330-N>show cam 1/1 show cam 1/1 Dest MAC/Route Dest Destination Ports ------------------- ----------------- 00-40-0d-59-03-78 00-d0-79-0a-0a-da 00-40-0d-43-1e-e9 00-40-0d-c6-24-01 Total Matching CAM Entries Displayed = 178 show cam mac User level: user, privileged, supervisor Use the show cam mac command to display the module and port number where a specific MAC address was learned.
Page 147: Show Cascading Fault-Monitoring
[<mod_num>] Example: P330-N>show cascading fault-monitoring 1 Module 1 cascading-down fault monitoring enabled. Module 1 cascading-up fault monitoring enabled. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The VLAN on which the MAC addresses were learned.
Page 148: Show Copy Status
Last warning show dev log file User level: privileged, supervisor. This command applies the P330-ML-ML switches only. Use the show dev log file command to display the encrypted device’s log file. The syntax for this command is: show dev log file Example: P330-N>show dev log file...
Page 149: Show Device-Mode
User level: user, privileged, supervisor Use the show device-mode command to show the current P330-ML-ML or P333R operating mode. Possible modes are Router, or Layer 2. This command is not available to the P333T, P334T, P332MF and P333T-PWR switches which do not have Router and to P333R-LB which is always in Load-Balancing mode.
Page 150: Show Erase Status
The syntax for this command is: show image version [<mod_num>] If no switch number is specified, the image version of the all switches will be displayed. Example: P330-N>show image version 1...
Page 151: Show Intelligent-Multicast
The syntax for this command is: show intelligent-multicast hardware-support Example: P330-N>show intelligent-multicast hardware support Intelligent-multicast HW configuration: Module ------- 1 Support IPMc Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Sub-Module ---------- Not Installed Support IPMc 600[Sec] 1800[Sec] 10[Sec] Cascade --------...
Page 152: Show Interface
(Maximum, Minimum, or Medium) of the Receive (Rx) buffer allocated to each port of the specified switch. Internal buffering for the P330-ML-ML switches will always have the value Not supported. This command is used to display the internal buffering status for the other P330-ML switches in the stack...
Page 153: Show Ip Access-Group
(including DSCP and composite operation tables). Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Switch number. If you do not specify a number then the internal buffering for all switches in the stack will...
Page 154: Show Ip Access-List-Dscp
Chapter 2 Avaya P330-ML Layer 2 CLI Commands The syntax for this command is: show ip access-list-details <policy-list-number> policy- A valid id number for a policy list currently defined for the module list- (100 to 199, 0 is the default list)
Page 155: Show Ip Access Lists
The current policy source is local default List (0) parameters List Owner : other List 0 is valid default action for list 0 is permit Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Precedence Name mandatory DSCP#0 mandatory DSCP#1...
Page 156: Show Ip Access-List-Summary
Chapter 2 Avaya P330-ML Layer 2 CLI Commands show ip access-list-summary User level: user, privileged, supervisor This command applies to the P334T-ML only when it is in device mode "Layer2". Use the show ip access-list-summary command to display a summary of policy lists.
Page 157: Show Ip Ssh
Use the show l2-module-config command to display Layer 2 module configuration. If this command is to be implemented on a switch other than the stack master, a session should be opened to the relevant switch. The syntax for this command is:...
Page 158 Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>show l2-module-config Please be patient. Gathering and displaying the information might take a while. P330-ML-N(super)# !# !# Upload time: !# System description: !# Master position: !# Module #: !# Module type, expansion type:...
Page 159 Chapter 2 Avaya P330-ML Layer 2 CLI Commands set port negotiation 2/11 disable set port duplex 2/11 half set port disable 2/15 set port negotiation 2/31 disable set trunk 2/40 dot1q set trunk 2/44 dot1q set port vlan 500 2/44...
Page 160: Show L2-Stack-Config
Use the show l2-stack-config command to display Layer 2 stack configuration. If this command is to be implemented on a switch other than the stack master, a session should be opened to the relevant switch. The syntax for this command is:...
Page 161 Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: Avaya P330-ML Reference Guide...
Page 162 Chapter 2 Avaya P330-ML Layer 2 CLI Commands P330-N>show l2-stack-config P330-ML-N(super)# !# !# Upload time: !# System description: !# IP address, netmask: !# Master position: !# Number of modules: set spantree priority 4096 set arp-tx-interval 0 set logging server 149.49.38.22 set logging server condition all Informational 149.49.38.22...
Page 163: Show License
149.49.77.235 secondary set allowed managers ip add 1.1.11.1 show license User level: privileged, supervisor. Use the show license command to display the current licenses installed on the stack. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands...
Page 164: Show Log
User level: privileged, supervisor. Use the show log command to display an encrypted device’s reset log. This command is for Avaya technical support use. The syntax for this command is: show log [mod_num] Example: P330-N>show log 1...
Page 165: Show Logging File Condition
The syntax for this command is: show logging file condition Example: P330-N>show logging file condition ********************************************************* Message logging configuration of FILE Sink Is Enabled Sink default severity: none Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands sink ***...
Page 166: Show Logging File Content
Chapter 2 Avaya P330-ML Layer 2 CLI Commands show logging file content User level: user, privileged, supervisor Use the show logging file content command to display the contents of the log file. The syntax for this command is: show logging file content [<severity>] [{all|<application>}] [<number>] [<module number>]...
Page 167 P330-N>show logging file content 7 all 1 > 08/04/2003,15:43:36:CLI-Notification: root: set logging file condition all 7 Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The application to which the filter applies. Possible values are: • BOOT • SYSTEM • ROUTER •...
Page 168: Show Logging Server Condition
Chapter 2 Avaya P330-ML Layer 2 CLI Commands show logging server condition User level: user, privileged, supervisor Use the show logging server condition command to display the condition and filtering of logging to the Syslog server. The syntax for this command is: show logging server condition <ip-address>...
Page 169: Show Logging Session Condition
Example: P330-N>show logout CLI timeout is 10 minutes show mac-aging User level: user, privileged, supervisor This command is available on P330-ML-ML switches only. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands sink *** ! Severity Override...
Page 170: Show Mac-Aging-Time
2 minutes longer. show module User level: user, privileged, supervisor Use the show module command to display switch status and information. For each switch with an expansion sub-module installed, both switch and expansion sub-module type and information are shown.
Page 171: Show Module-Identity
The syntax for this command is: show module-identity [module] Example: P330-N>show module-identity Module Identity --------------- 1234567 4144162 Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Statuses ---- -------- ---------------------------- 4144162 PS:OK Fans:OK Mode:Layer2 Conn-Up:Fail Conn-Down:Ok BUPS:Not Prsnt Fans:None Type:None 4455428...
Page 172: Show Port
Level Speed Type Number of the switch. If you do not specify a number, the ports on all the switches are shown. Number of the port on the module (can be a vitrual LAG port number). If you do not specify a number, all the ports on the switch are shown.
Page 173: Show Port Auto-Negotiation-Flowcontrol-Advertisement
Number of the switch. If you do not specify a number, the modules on all the switches are shown. Number of the port on the switch. If you do not specify a number, all the ports on the switch are shown.
Page 174 Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>show port channel Port Channel Status ------ --------------- ---------------- ---------------- P330-N>show port channel 3/3 info Port Speed ------ ------ ------- ----- --------- -------- -------- Channel Name MEIR MEIR my-channel my-channel my-channel...
Page 175: Show Port Classification
Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Number of the switch. If you do not specify a number, the ports on all the switches are shown. Number of the port on the module. If you do not specify a number, all the ports on the module are shown.
Page 176: Show Port Dot1X
Chapter 2 Avaya P330-ML Layer 2 CLI Commands show port dot1x User level: user, privileged, supervisor Use the show port dot1x command to display all the configurable values associated with the authenticator port access entity (PAE) and backend authenticator. The syntax for this command is: show dot1x [mod]/[port] Number of the module.
Page 177 Quiet Period ReAuth Period Server Tmout Supp Tmeout Tx Priod Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The current state od the Backend Authentication state machine. Possible states include: • Request • Response • Success •...
Page 178: Show Port Dot1X Statistics
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Max Req show port dot1x statistics User level: user, privileged, supervisor Use the show port dot1x statistics command to display all the port dot1x statistics. The syntax for this command is: show dot1x statistics [mod]/[port] Number of the module.
Page 179: Show Port Edge State
------------- edge-port non-edge-port Number of the switch . If you do not specify a number, all switches are shown. Number of the port on the switch. If you do not specify a number, all ports on the specified switch are shown.
Page 180 Chapter 2 Avaya P330-ML Layer 2 CLI Commands Output Fields Field Port Send- Flowcontrol- Admin Send- Flowcontrol- Oper Receive- Flowcontrol- Admin Receive- Flowcontrol- Oper Description Module and port number Send flow-control administration. Possible settings: • ON indicates that the local port is allowed to send flow control frames to the far end.
Page 181: Show Port Mirror
Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands point-to-point oper state -------------------------- point to point connection point to point connection point to point connection point to point connection point to point connection...
Page 182: Show Port Redundancy
User level: user, privileged, supervisor Use the show port security command to list the security mode of the ports of a switch or stack. When no port number is specified, this command displays all the secured ports in the stack.
Page 183: Show Port Trap
Number of the switches. If you do not specify a number, the ports on all the switches are shown. Number of the port on the switch. If you do not specify a number, all the ports on the switch are shown.
Page 184: Show Powerinline
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>show port vlan-binding-mode port 2/1 is statically bound port 2/2 is statically bound port 2/3 is statically bound port 2/4 is statically bound port 2/5 is statically bound port 2/6 is statically bound...
Page 185: Show Powerinline Image Version
This command applies to P333T-PWR switches only and is used by P330- ML-ML switches to control P333T-PWR modules in the stack. Use the show powerinline image version command to display the current Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Inline Power Operational Allocated...
Page 186: Show Ppp Authentication
Chapter 2 Avaya P330-ML Layer 2 CLI Commands image version of P333T-PWR switches in the stack or a specific switch. The syntax of this command is: show powerinline image version [<module-number>] If you do not specify a number, then the software version for all the P333T-PWR switches is shown.
Page 187: Show Ppp Baud-Rate
Use this show ppp incoming timeout command to display the amount of time in minutes that a PPP session can remain idle before being automatically disconnected. The syntax for this command is: show ppp incoming timeout Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands None...
Page 188: Show Ppp Session
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>show ppp incoming timeout PPP incoming timeout is 15 minutes show ppp session User level: user, privileged, supervisor Use the show ppp session command to display PPP parameters and statistics of an active PPP session.
Page 189: Show Queuing Scheme
Use the show queuing scheme command to display the current queuing scheme settings. If this command is to be implemented on a P330-ML-ML switch other than the stack master, a session should be opened to the relevant switch. The syntax for this command is:...
Page 190: Show Rmon Alarm
Chapter 2 Avaya P330-ML Layer 2 CLI Commands show rmon alarm User level: user, privileged, supervisor Use the show rmon alarm command to display the parameters set for a specific alarm entry that was set using the rmon alarm command on or using the P330-ML Manager.
Page 191: Show Rmon Event
[<History Index>] History Index Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands History index defined using rmon event command or the P330-ML Manager History index defined using rmon history command or RMON management tool...
Page 192: Show Rmon Statistics
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>show rmon history 1026 history Entry 1026 is active, owned by amir Monitors ifEntry.1.1026 every 30 seconds Requested # of time intervals, ie buckets, is 20 Granted # of time intervals, ie buckets, is 20...
Page 193: Show Secure Current
The syntax for this command is: show secure mac [<mod-num>/<port-num> mod-num Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Time Since Last Request(In Sec) ------------------------------------ Module where the secured port is located...
Page 194: Show Security Mode
Chapter 2 Avaya P330-ML Layer 2 CLI Commands port-num Example: P330-N# show secure mac port 1/7 Port Secure-Src-Addrs ------ ----------------- 00-40-0d-9b-9d-00 00-40-0d-98-61-2e 00-40-0d-8a-a3-23 show security mode User level: user, privileged, supervisor Use the show security mode command to display the status of the MAC security feature.
Page 195 Trap-Rec-Address ---------------- 135.64.100.73 SNMPv3 Notifications Status ----------------------------- Traps: Enabled Informs: Enabled Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Community-String ---------------- public public meir Status Traps Configured -------- ---------------- Enabled config fault trafic_threshold...
Page 196: Show Snmp Engineid
Chapter 2 Avaya P330-ML Layer 2 CLI Commands SNMP-Rec-Address Model ---------------- ----- ------- --------------- ----------- ------------------ 135.64.100.73 UDP port: 162 149.64.100.73 UDP port: 162 show snmp engineID User level: supervisor Use the show snmp engineID command to display SNMP engine information.
Page 197: Show Snmp Group
[<group-name>] group-name (optional) Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Description The SNMP engine ID. The number of times the SNMP engine has been started or reinitialized. The name of a group to display. If no group is...
Page 198 Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>show snmp group Group Name: initial Security Model: v3 Security Level: noauth Read View: iso Write View: iso Notify View: iso Status: active Group Name: ReadCommG Security Model: v1 Security Level: noauth...
Page 199: Show Snmp Retries
User level: user, privileged, supervisor Use the show snmp timeout command to display the default SNMP timeout in seconds. The SNMP timeout is only for the Avaya P330-ML Embedded Web Manager. Tip: This command is useful for access using the Device Manager.
Page 200: Show Snmp Usertogroup
Chapter 2 Avaya P330-ML Layer 2 CLI Commands information for a specific user. The syntax for this command is: show snmp user [<user>] user (Optional) Example: P330-N>show snmp user initial EngineId: 1a:e9:00:00:01:95:31:4b:64 User Name: initial Authentication Protocol: none Privacy Protocol: none...
Page 201: Show Snmp View
The syntax for this command is: show snmp view [<viewname>] viewname (Optional) Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Name of the view. If you do not specify a view, the configuration of all SNMP views is displayed.
Page 202 Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>show snmp view snmpv1View View Name: snmpv1View Subtree Oid: 1 Subtree Mask: View Type: include Storage Type: nonVolatile Status: active View Name: snmpv1View Subtree Oid: 1.3.6.1.6 Subtree Mask: View Type: exclude...
Page 203: Show Spantree
Number of the switch. If you do not specify a number, all switches are shown. Number of the port on the switch. If you do not specify a number, all ports on the specified switch are shown.
Page 204 Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>show spantree Spanning tree state is enabled Designated Root: Designated Root Priority: 32768 Designated Root Cost: 100 Designated Root Port: 1/7 Root Max Age: 20 Root Forward Delay: 15 Bridge ID MAC ADDR: 00-40-0d-b9-89-ff...
Page 205 Tx Hold Count Soanning Tree Version Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Description Status of whether Spanning-Tree Protocol is enabled or disabled MAC address of the designated spanning-tree root bridge Priority of the designated root bridge...
Page 206: Show System
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Spanning Tree Default Path Costs Port State Cost Priority show system User level: user, privileged, supervisor Use the show system command to display the up time, system name, location, and contact person.
Page 207: Show Tftp Download Software Status
Use the show time command to display the current P330-ML time and timezone. The syntax for this command is: show time Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands : p340_4_0_4.web : 149.49.100.51 : Idle : (null)
Page 208: Show Time Parameters
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>show time 10:32:34 27 JAN 2000 GMT show time parameters User level: user, privileged, supervisor Use the show time parameters command to display the time status and parameters. The syntax for this command is:...
Page 209: Show Trunk
Number of the switch. If you do not specify a number, all switches in the stack are shown. Number of the port on the switch. If you do not specify a number, all ports on the specificity switch are shown.
Page 210: Show Upload Status
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N>show trunk 4/1-2 P330-ML-1(super)# show trunk 1/42-44 Port Mode Binding mode ------ ----- ------------------------- ----------- ---------------------- 1/42 bound to configured vlans Port Mode Binding mode ------ ----- ------------------------- ----------- ---------------------- 1/43...
Page 211: Show Username
Use the show utilization command to display CPU utilization statistics for modules in the stack. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Number of the module. If you do not specify a number, upload statuses for all modules in the stack are shown. : stack-config : 149.49.36.200...
Page 212 Chapter 2 Avaya P330-ML Layer 2 CLI Commands The syntax for this command is: show utilization <module-number> module-number Example: P330-1(super)# show utilization 5sec 60sec ------ ----- Appl. Disabled The module for which to display utilization statistics. If no module is specified, utilization statistics for all modules is displayed.
Page 213: Show Vlan
Switch Ports statically bound to this vlan: In module 1 : 43 Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The VLAN ID for which to display bound ports. The VLAN name for which to display bound ports.
Page 214: Show Web Aux-Files-Url
User level: user, privileged, supervisor Displays the URL/directory from where the switch can access the Device Manager auxiliary files (for example help files). The syntax for this command is: show web aux-files-url Example: P330-N>show web aux-files-url...
Page 215: Snmp-Server Enable
User level: supervisor Use the snmp-server command to enable SNMP Access to the switch. The syntax for this command is: snmp-server enable [volatile] volatile (Optional) Example: P330-N>snmp-server enable Done! snmp-server enable notifications User level: supervisor Use the snmp-server enable notifications command to enable sending all Simple Network Management Protocol (SNMP) notifications (traps and informs).
Page 216: Snmp-Server Group
Chapter 2 Avaya P330-ML Layer 2 CLI Commands The syntax for this command is: snmp-server engineID <engineID> engineID Example: P330-N>snmp-server engineID 1a:e9:00:00:01:95:31:8a:9d P330-N>EngineID changed P330-N>Done! snmp-server group User level: supervisor Use the snmp-server group command to configure SNMPv3 groups. The syntax for this command is: snmp-server group <groupname>...
Page 217: Snmp-Server Host
Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Keyword that specifies a view for SNMP notifications. If this keyword is not included in the command, the group has no associated notify view. The name of the view for SNMP notifications.
Page 218: Snmp-Server Informs
Chapter 2 Avaya P330-ML Layer 2 CLI Commands udp-port (Optional) port notification -type-list (Optional) Example: P330-N>snmp-server host 149.49.38.221 informs v3 noauth charlieBrown Done! snmp-server informs User level: supervisor Use the snmp-server informs command to configure inform parameters. Keyword that specifies that a specific UDP port on the target host should be used when sending notifications to the host.
Page 219: Snmp-Server Remote-User
Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Maximum number of times to resend an inform request. Number of seconds to wait for an acknowledgment before resending. The default is 3. Variable that specifies the name of the SNMP user. The maximum length is 32 bytes.
Page 220: Snmp-Server User
Chapter 2 Avaya P330-ML Layer 2 CLI Commands priv des56 (Optional) auth- password Example: P330-N>snmp-server remote-user charles 22:00:00:01:6e:4a:32:22:01 2L2NotifyG3 Done! snmp-server user User level: supervisor Use the snmp-server user command to configure a new SNMP user. The syntax for this command is: snmp-server user <username>...
Page 221: Snmp-Server View
You can only run this command on a stack. Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands Name of the view. Object identifier (OID) of the ASN.1 subtree to be included or excluded from the view. To identify the subtree, specify a text string consisting of numbers, such as 1.3.6.2.4.
Page 222: Sync Time
Chapter 2 Avaya P330-ML Layer 2 CLI Commands The stack is reset once the command has been executed. You should not load the stack with traffic during this test. Please follow the instruction shown on the CLI screen, during the various stages of this test.
Page 223: Terminal
Avaya P330-ML Reference Guide Chapter 2 Avaya P330-ML Layer 2 CLI Commands The IP address of the remote host. The port number over which to open the Telnet connection. New user name (minimum four characters) User’s password (minimum four characters)
Page 224: Validate-Group
Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-1(super)# username john password johnny access-type read-write User account added. P330-1(super)# username root password secret access-type read-write ERROR: User account root has always an administrator access type. P330-1(super)# username root password secret access-type admin User account modified.
Page 225 Chapter 2 Avaya P330-ML Layer 2 CLI Commands Example: P330-N# validate-group 101 List 101 is valid-in-progress P330-N# validate-group 101 List 101 is valid The validation process may take some time to complete. Avaya P330-ML Reference Guide...
Page 226 Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guide...
Page 227: Router Configuration Contexts
Chapter 3 Avaya P330-ML Layer 3 CLI Commands This chapter provides all the Layer 3 CLI (Command Line Interface) commands, parameters, and their default values. How the Layer 3 CLI is Organized The commands that make up the Layer 3 CLI are organized alphabetically and according to context.
Page 228: Chapter 3 Avaya P330-Ml Layer 3 Cli Commands
Chapter 3 Avaya P330-ML Layer 3 CLI Commands General Commands User level: privileged, supervisor. If you are at the “privileged” level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode.
Page 229: Clear Arp-Cache
Flushing all arp entries Flushed 100 ARP entries Done! Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands The amount of time, in seconds, that an entry remains in the arp cache. VLAN string (up to 16 characters) IP address...
Page 230: Clear Fragment
Chapter 3 Avaya P330-ML Layer 3 CLI Commands clear fragment User level: privileged, supervisor. Use the clear fragment command to restore fragment action database defaults and free all waiting fragments. The syntax for this command is: clear fragment Example: Router-N# clear fragment...
Page 231: Clear Ip Traffic
Router-N(configure)# clear vlan 2 name vlan2 If you wish to enter a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”. Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands VLAN number VLAN name...
Page 232: Configure
Chapter 3 Avaya P330-ML Layer 3 CLI Commands configure User level: privileged, supervisor. Use the configure command to enter configure mode. The syntax for this command is: configure Example: P330-1(super)# configure Router-N(configure)# copy module-config scp Use the copy module-config scp command to upload the switch-level parameters from the current NVRAM running configuration into a file via SCP.
Page 233: Copy Module-Config Tftp
* download operations. ******************************************************************** copy running-config scp Use the copy running-config scp command to upload the current switch-level parameters from the current NVRAM running configuration into a file via SCP. The syntax for this command is: copy running-config scp <filename> <ip> <mod_num>...
Page 234: Copy Running-Config Startup-Config
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Example: P330-N# copy running-config scp c:\config\switch1.cfg 192.168.49.10 5 Beginning upload operation ... This operation may take a few minutes... Please refrain from any other operation during this time. For more information , use 'show upload status' command...
Page 235: Copy Scp Module-Config
Use the copy scp module-config command to download a module configuration to the device via SCP. Only parameters that differ from the factory default settings for the switch are included in the configuration file. Therefore, it is important to reinitialize the NVRAM to the factory default settings before downloading configuration files to the switch.
Page 236: Copy Scp Startup-Config
Use the copy scp startup-config command to download a startup configuration to the device via SCP. Only parameters that differ from the factory default settings for the switch are included in the configuration file. Therefore, it is important to reinitialize the NVRAM to the factory default settings before downloading configuration files to the switch.
Page 237: Copy Startup-Config Tftp
User level: privileged, supervisor. Copies the policy and router configurations from the saved TFTP file to the Startup Configuration file in the NVRAM. Only parameters that differ from the factory default settings for the switch are Avaya P330-ML Reference Guide Chapter 3...
Page 238: Disconnect Ssh
Chapter 3 Avaya P330-ML Layer 3 CLI Commands included in the configuration file. Therefore, it is important to reinitialize the NVRAM to the factory default settings before downloading configuration files to the switch. To reinitialize the NVRAM, run the nvram initialize command.
Page 239: Event Log
Router-N(configure)# erase startup-config event log Use the event log command to display a list of the event messages. The event messages shown are encrypted and are reserved for Avaya use only. The syntax for this command is: event log [<num>]...
Page 240: Fragment Chain
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Example: Router-N(configure router:rip)# exit Router-N(configure)# fragment chain Use the fragment chain command to set the maximum number of fragments that can comprise a single IP packet destined to the router. Use the no form of this command to set the fragment chain to the default value (64).
Page 241: Fragment Timeout
<command> command Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands The maximum number of seconds to re-assemble an IP packet, from 5 to 120. The default is 10. A specific CLI command or group of commands...
Page 242: Hostname
Use the no hostname command to return the system prompt to its default. This command does not change the system prompt of the switch. To change the system prompt of the switch, use the host name command in the Layer 2 tree. The syntax for this command is: [no] hostname [<hostname_string>]...
Page 243: Interface
<policy-list-number> <default- Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands The rate of echo requests per second. Value range = 1 to 1000. Default = 50. String (up to 32 characters). This name should not...
Page 244: Ip Access-Group
Chapter 3 Avaya P330-ML Layer 3 CLI Commands action> <policy-list-number> <default-action> Example: Router-N(configure)# ip access-default-action 101 default- action-deny Done! ip access-group User level: privileged, supervisor. Use the ip access group command to activate a specific policy list. The syntax for this command is: ip access-group <policy-list-number>...
Page 245: Ip Access-List-Cookie
The syntax for this command is: ip access-list-cookie <policy-list-number> <cookie> policy-list-number cookie Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands <source-ip>}[<operator> <port> [<port]] {<destination-ip> <destination- wildcard>|any |host <destination-ip>}[<operator> <port> [<port>]][established] [precedence] integer (100 - 149)
Page 246: Ip Access-List-Copy
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Example: Router-N# ip access-list-cookie 101 12345 ip access-list-copy User level: privileged, supervisor. Use the ip access-list-copy command to copy a configured source policy list to a destination policy list. The syntax for this command is: ip access-list-copy <source-list>...
Page 247: Ip Access-List-Dscp Trust
Forward the packet with its original 802.1p priority (default) trust-dscp Forward the packet with the maximum priority between 802.1p and the priority obtained from the DSCP-CoS mapping table Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands...
Page 248: Ip Access-List-Name
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Example: Router-N(configure)# ip access-list-dscp trust 100 trust- dscp Done! ip access-list-name User level: privileged, supervisor. Use the ip access-list-name command to set a name for a policy list. The syntax for this command is: ip access-list-name <policy-list-number>...
Page 249: Ip Bootp-Dhcp Relay
Example: To enable relaying of BOOTP and DHCP requests: Router-N(configure)# ip bootp-dhcp relay Done! To disable relaying of bootp and dhcp requests: Router-N(configure)# no ip bootp-dhcp relay Done! Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands...
Page 250: Ip Default-Gateway
Chapter 3 Avaya P330-ML Layer 3 CLI Commands ip default-gateway User level: privileged, supervisor. If you are at the ”privileged” level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode.
Page 251: Ip Max-Route-Entries
Configure mode. Type configure at the command prompt to enter configure mode. The ip max-route-entries command exists for compatibility with Avaya™ P550. There is no limitation on the size of the routing table, except for the amount of available memory.
Page 252: Ip Ospf Router-Id
Chapter 3 Avaya P330-ML Layer 3 CLI Commands a dotted decimal. The syntax for this command is: [no] ip netmask-format <mask-format> The possible mask formats are: bitcount decimal hexadecimal Example: To display netmasks in decimal format: Router-N(configure)# ip netmask-format bitcount decimal...
Page 253: Ip Route
Type configure at the command prompt to enter configure mode. Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands The IP address of the network Mask of the static route The next hop address in the network The path cost.
Page 254: Ip Simulate
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Use the ip routing command to enable IP routing. Use the no ip routing command to disable the IP routing process in the device. By default, IP routing is enabled. The syntax for this command is:...
Page 255: Ping
64 bytes from 149.49.48.1: icmp_seq=1. time=0. ms 64 bytes from 149.49.48.1: icmp_seq=2. time=0. ms ----149.49.48.1 PING Statistics---- 3 packets transmitted, 3 packets received, 0% packet loss round-trip (ms) prompt-length Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands min/avg/max = 0/0/0...
Page 256: Reset
Chapter 3 Avaya P330-ML Layer 3 CLI Commands User level: privileged, supervisor. Use the CLI prompt length command to set the length of the command prompt that is displayed. The syntax for this command is: prompt-length <full | prompt-size> full...
Page 257: Router Rip
Use the router srrp command to enable srrp redundancy for the main router and enter the “router srrp” context. Use the no router srrp command to disble srrp redundancy for the main router. Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands...
Page 258: Router Vrrp
User level: user, privileged, supervisor Use the session command to open a session with a specific entity in a switch of the stack. For example, you can open a session with the Routing entity of a P332G-ML switch in the stack.
Page 259: Set Device-Mode
Use the set device-mode command to change the basic mode of operation of the switch between Router and Layer 2 modes. This command is available on P330-ML-ML and P333R switches only. The syntax for this command is: set device-mode <mode>...
Page 260: Set Policy Type
P334T-ML through Fast Ethernet ports router - apply policy on routed packets only local or policy server • The default policy source for P330-ML-ML switches is local • The default policy source for P333R and P333R-LB switches is policy-server Avaya P330-ML Reference Guide...
Page 261: Set System Contact
Done! If you wish to enter a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”. Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands System contact System name...
Page 262: Set System Name
Chapter 3 Avaya P330-ML Layer 3 CLI Commands set system name User level: privileged, supervisor. Use the set system name command to set the mib2 system name MIB variable. The syntax for this command is: set system name [string] string...
Page 263: Set Vlan
Module #1 =========== Module Source file Destination file : .router-running Host Running state Failure display Last warning Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands VLAN number VLAN name : .router-startup : Idle : (null) : No-warning...
Page 264: Show Device-Mode
Device mode is router show download status User level: user, privileged, supervisor This command applies the P330-ML-ML switches only. Use the show download status command to display a summary of the last software download operation. The syntax for this command is:...
Page 265: Show Fragment
Number of packets which overflowed the database is 0 Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands Maximum number of packets set by the fragment size command Maximum number of fragments for a single packet set by the fragment chain command.
Page 266: Show Ip Access-Group
User level: user, privileged, supervisor Use the show ip access-group command to see information about the configured active access list. This command is available on P330-ML-ML switches only. The syntax for this command is: show ip access-group Example: Router-N>...
Page 267: Show Ip Access-List-Dscp
Use the show ip access-list-summary command to display a list of all configured access lists. The syntax for this command is: show ip access-list-summary Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands Precedence Name mandatory DSCP#0 mandatory...
Page 268: Show Ip Arp
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Example: Router-N> show ip access-list-summary The policy lists summary: default List (0) show ip arp User level: user, privileged, supervisor Use the show ip arp command to display the Address Resolution Protocol (ARP) cache.
Page 269: Show Ip Icmp
Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands The name of the interface whose information you want to display. The name or ID of the VLAN over which there are interfaces you want to display.
Page 270: Show Ip Interface Brief
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Example: Router-N> show ip interface Showing 2 Interfaces mgmt is administratively up On vlan Default Internet address is 10.49.54.14 255.255.255.0 Broadcast address is 10.49.54.255 Directed broadcast forwarding is disabled Proxy ARP is disabled...
Page 271: Show Ip Ospf
The syntax for this command is: show ip ospf database [<ls type>] ls-types: asbr-summary router Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands Address Mask 149.49.54.56 255.255.255.0 Displays information only about the autonomous system boundary router summary LSAs. Optional.
Page 272: Show Ip Ospf Interface
Chapter 3 Avaya P330-ML Layer 3 CLI Commands network network-summary external show ip ospf interface User level: user, privileged, supervisor Use the show ip ospf interface command to display OSPF-related interface information. The syntax for this command is: show ip ospf interface [<interface-name>]...
Page 273: Show Ip Protocols
Invalid after 180 seconds, flushd after 300 Redistributing: rip Default version control: rip version 1 Interface Routing for Networks: Routing Information Sources: Gateway Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands RIP | OSPF. Version Last Update...
Page 274: Show Ip Reverse-Arp
Chapter 3 Avaya P330-ML Layer 3 CLI Commands show ip reverse-arp User level: user, privileged, supervisor Use the show ip reverse-arp command to display the IP address of a host, based on a known MAC address. The syntax for this command is: show ip reverse-arp <mac addr>...
Page 275: Show Ip Route Best-Match
135.0.0.0 255.0.0.0 135.64.0.0 255.255.0.0 149.49.0.0 255.255.0.0 149.49.2.0 255.255.255.0 Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands IP address Mask Interface 255.255.0.0 e-135new The IP address of the routes The ip mask of the routes. Interface e-36...
Page 276: Show Ip Route Summary
Chapter 3 Avaya P330-ML Layer 3 CLI Commands show ip route summary User level: user, privileged, supervisor Use the show ip route summary command to display the number of routes known to the switch. The syntax for this command is:...
Page 277: Show Ip Traffic
Use the show ip traffic command to display the IP traffic statistics counters. The syntax for this command is: show ip traffic Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands Oper State Poll interval ---------- -------------...
Page 278 Chapter 3 Avaya P330-ML Layer 3 CLI Commands Example: Router-N> show ip traffic IP statistics: Received: 1365359 total, 45659 local destination 0 bad hop count, 0 packet header errors 0 unknown protocol, 136786 address errors 1182914 discarded Fragments: 0 reassembled, 0 timeouts...
Page 279: Show Ip Unicast Cache
[[<src addr> <src mask>] <dst addr> <dst mask>} src addr src mask dst addr dst mask Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands The source IP address. The source mask IP address. The destination IP address. The destination mask IP address.
Page 280: Show Ip Unicast Cache Networks
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Example: Router-N> show ip unicast cache Showing 6 Sessions. Source IP =============== ============= 192.168.1.1 192.168.2.1 192.168.2.2 192.168.2.3 192.168.2.4 192.168.2.5 show ip unicast cache networks User level: user, privileged, supervisor Use the show ip unicast cache networks command to display a summary of networks handled by the hardware unicast cache database.
Page 281: Show Ip Unicast Cache Networks Detailed
The syntax for this command is: show ip unicast cache networks detailed[<net addr> <net mask>] net addr net mask Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands Mask Next Hop(s) Total Hosts 16 10.2.0.2 16 0.0.0.0 8 192.168.0.130 24 10.2.0.2...
Page 282: Show Ip Unicast Cache Nexthop
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Example: Router-N> show ip unicast cache networks detailed 192.168.6.0 24 Showing 3 rows NetworkMask ============ 192.168.6.0 show ip unicast cache nextHop User level: privileged, supervisor. Use the show ip unicast cache nextHop command to list the routers that are used as next-hop routers.
Page 283: Show Ip Vrrp
The syntax for this command is: show ip vrrp detail Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands 2621 Filter by VLAN. Filter by virtual router ID (1-255) The virtual router ID. Provide detailed information.
Page 284: Show Policy Type
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Example: Router-N> show ip vrrp detail VRRP is globally enabled Virtual Router on VLAN: Router-id: State: Priority: Advertisement Interval: Last State Change: Override Address Ownership Rule: No Authentication Type: Authentication Key: Master IP Address...
Page 285 (for modules in 'device- mode router'). The syntax for this command is: show policy type Example: Router-N# show policy type Policy type is router Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands...
Page 286: Show Startup-Config
Use the show startup-config command to show configuration loaded at startup. The syntax for this command is: show startup-config Example: Router-N> show startup-config ! Avaya Inc. P333R Switch - Router configuration ! version 4.0.5 hostname "R1-Backup" interface "net" ip vlan name "Default" ip address 149.49.54.56 ip default-gateway 149.49.54.1...
Page 287: Show Upload Status
Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands Number of the module. If you do not specify a number, upload statuses for all modules in the stack are shown.
Page 288: Traceroute
Chapter 3 Avaya P330-ML Layer 3 CLI Commands The syntax for this command is: terminal {width|length} [<characters>] Example: Router-N> terminal width 80 terminal width: 80 traceroute User level: user, privileged, supervisor Use the traceroute command to initiate a traceroute to a remote host.
Page 289 Chapter 3 Avaya P330-ML Layer 3 CLI Commands The validation process may take some time to complete. Avaya P330-ML Reference Guide...
Page 290: Interface Context
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Interface Context You can only access these commands in the “interface” context. Type interface [name] at the command prompt to enter the “interface” context if necessary. default-metric User level: privileged, supervisor. Use the default metric command to set the interface RIP route metric.
Page 291: Ip Address
Example: Router-N(config-if:marketing)# ip admin-state up Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands The IP address assigned to the interface. Mask for the associated IP subnet The administration status – either Up or Down Administrative state of the interface.
Page 292: Ip Bootp-Dhcp Network
Chapter 3 Avaya P330-ML Layer 3 CLI Commands ip bootp-dhcp network User level: privileged, supervisor. Use the ip bootp-dhcp network command to configure the network from which the BOOTP/DHCP server shall allocate an address. Use the no ip bootp-dhcp network command to remove a network.
Page 293: Ip Broadcast-Address
Use the no ip directed-broadcast command to disables net-directed broadcasts on an interface. The syntax for this command is: [no] ip directed-broadcast Example: Router-N(config-if:marketing)# ip directed broadcast Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands The broadcast IP address...
Page 294: Ip Netbios-Rebroadcast
Chapter 3 Avaya P330-ML Layer 3 CLI Commands ip netbios-rebroadcast User level: privileged, supervisor. Use the ip netbios-rebroadcast command to set the NETBIOS rebroadcasts mode on an interface. Use the no ip netbios-rebroadcast command to disable NETBIOS rebroadcasts on an interface.
Page 295: Ip Ospf Cost
Use this command to specify the time interval between OSPF hello messages the router sends. Use no ip ospf hello-interval to set the hello-interval to its default. The default is 10. Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands integer Time in seconds (integer value)
Page 296: Ip Ospf Priority
Chapter 3 Avaya P330-ML Layer 3 CLI Commands The syntax for this command is: [no] ip ospf hello-interval <seconds> seconds Example: Router-N(configure-if:marketing) # ip ospf hello-interval 5 Done! ip ospf priority User level: privileged, supervisor. Use the ip ospf priority command to configure interface priority used in DR election.
Page 297: Ip Redirects
To set the authentication string used on the interface “marketing” to be “hush- hush”. Router-N(configure-if:marketing) # ip rip authentication key hush-hush Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands The authentication string for the interface. Up to 16 characters are allowed.
Page 298: Ip Rip Authentication Mode
Chapter 3 Avaya P330-ML Layer 3 CLI Commands ip rip authentication mode User level: privileged, supervisor. Use the ip rip authentication command to specify the type of authentication used in RIP Version 2 packets. Use the no ip rip authentication command to restore the default value of none.
Page 299: Ip Rip Poison-Reverse
User level: privileged, supervisor. Use the ip rip rip-version command to specify the RIP version running on the interface basis. The syntax for this command is: ip rip rip-version <version> Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands...
Page 300: Ip Rip Send-Receive-Mode
Chapter 3 Avaya P330-ML Layer 3 CLI Commands The possible versions of the RIP packets received and sent on an interface are: Example: To specify that RIP version 2 should be running on the basis of the interface “marketing”: Router-N(configure-if:marketing) # ip rip rip-version 2...
Page 301: Ip Rip Split-Horizon
RT_PRIMARY_MGMT, the IP address used in MSNM is selected randomly. The syntax for this command is: ip routing-mode <mode> mode Example: Router-N(config-if:marketing)#ip routing-mode RT_PRIMARY_MGMT Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands RT_MGMT or RT_PRIMARY_MGMT mode...
Page 302: Ip Srrp Backup
User level: privileged, supervisor. Use the ip srrp backup command to backup an additional interface of the main router using the SRRP application. If the main router fails, the switch takes over its activities on all configured interfaces. The syntax for this command is: ip srrp backup <main router addr>...
Page 303: Ip Vrrp Address
To assign address 10.0.1.2 to virtual router 1: Router-N(configure-if:marketing) # ip vrrp 1 address 10.0.1.2 Done! Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands Virtual Router ID (1-255) Virtual Router ID (1-255) The IP address to be assigned to the virtual router.
Page 304: Ip Vrrp Auth-Key
Chapter 3 Avaya P330-ML Layer 3 CLI Commands ip vrrp auth-key User level: privileged, supervisor. Use the ip vrrp auth-key command to set the virtual router simple password authentication for the virtual router ID. Use the no ip vrrp auth-key command to disable simple password authentication for the virtual router instance.
Page 305: Ip Vrrp Preempt
192.168.66.23 Done! Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands Virtual Router ID (1-255) Virtual Router ID (1-255) Primary IP address of the virtual router. This address should be one of the router addresses on the VLAN.
Page 306: Ip Vrrp Priority
Chapter 3 Avaya P330-ML Layer 3 CLI Commands ip vrrp priority User level: privileged, supervisor. Use the ip vrrp priority command to set the virtual router priority value used when selecting a master router. Use the no ip vrrp priority command to restore the default value.
Page 307: Router Rip Context
The syntax for this command is: [no] redistribute <protocol> protocol Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands The IP address of the network of directly connected networks Wildcard mask address. Exists for compatibility with P550. Either Static or OSPF...
Page 308: Timers Basic
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Example: Router-N(configure router:rip)# redistribute ospf Done! timers basic User level: privileged, supervisor. Use the timers basic command to configure the route timer. Use the no timers basic command to restore the timers to their default values.
Page 309: Router Ospf Context
The default is disabled. The syntax for this command is: network <net addr> [<wildcard-mask> [area <area id>]] net addr wildcard-mask Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands IP address Stub IP address Wildcard mask address...
Page 310: Passive-Interface
Chapter 3 Avaya P330-ML Layer 3 CLI Commands area id Example: Router-N(configure router:ospf)# network 192.168.0.0 Router-N(configure router:ospf)# area 192.168.0.0 0.0.255.255 area 0.0.0.0 passive-interface User level: privileged, supervisor. Use the passive interface command to allow interfaces to be flooded into the OSPF domain as OSPF routes and not external routes.
Page 311: Timers Spf
The syntax for this command is: [no] timers spf <spf-holdtime> spf-holdtime Example: Router-N(configure router:rip)# timers spf 5 Done! Avaya P330-ML Reference Guide Chapter 3 Avaya P330-ML Layer 3 CLI Commands The time in seconds of the delay between runs of OSPF’s SPF calculation.
Page 312: Router Srrp Context
Chapter 3 Avaya P330-ML Layer 3 CLI Commands Router SRRP Context You can only access these commands in the “Router-SRRP” context. Type router srrp at the command prompt to enter the “Router -SRRP” context if necessary. poll-interval User level: user, privileged, supervisor Use the poll-interval command to configure the polling interval in seconds used by SRRP.
Page 313: Clear Cam
221 copy tftp module-config 27 copy tftp stack-config 27 copy tftp SW_image 29 crypto key generate dsa 31 dir 32 Avaya P330-ML Reference Guide disable interface 31 disconnect ssh 33 get time 34 hostname 35 ip http enable 41...
Page 314 114 set snmp trap 114 set snmp trap auth 115 set spantree 116 set spantree priority 118 set system contact 119, 120, 244, 245 set system location 120, 245 set system name 121, 246 Avaya P330-ML Reference Guide...
Page 315 154 show module 154 show module identity 156 show port 157 show port auto-negotiation-flowcontrol 158 Avaya P330-ML Reference Guide Index of Layer 2 CLI Commands show port classification 160 show port flowcontrol 164 show port mirror 166...
Page 316 200 snmp-server engineID 200 snmp-server group 201 snmp-server host 202 snmp-server informs 203 snmp-server remote-user 204 snmp-server user 205 snmp-server view 206 sync time 207 tech 207 telnet 207 terminal 9 username 208 Avaya P330-ML Reference Guide...
Page 317: Index Of Layer 3 Cli Commands
227 help 228 hostname 228 icmp in-echo-limit 229 interface 229 ip access-default-action 230 ip access-group 230 Avaya P330-ML Reference Guide ip access-list 231 ip access-list-cookie 232 ip access-list-copy 232 ip access-list-dscp operation 233 ip access-list-dscp trust 233 ip access-list-name 234...
Page 318 276 show ip unicast cache summary 276 show ip vrrp 277 show ip vrrp detail 278 show policy type 279 show rmon2 auto-learn 283 show rmon2 filters 283 show rmon2 host 281 show rmon2 host-top-n 284 Avaya P330-ML Reference Guide...
Page 319 285 show rmon2 state 280 show rmon2 subnets 282 show rmon2 subnet-top-n 285 show startup-config 286 show system 286 Avaya P330-ML Reference Guide Index of Layer 3 CLI Commands show upload status 287 show vlan 287 terminal 287 timeout 312...
Page 320 Index of Layer 3 CLI Commands Avaya P330-ML Reference Guide...

Avaya P330-ML-ML Reference Manual

Chapter 1 Using the CLI

Chapter 2 Avaya P330-ML Layer 2 CLI Commands

Quick Links

Related Manuals for Avaya P330-ML-ML

Summary of Contents for Avaya P330-ML-ML